带有加权基线长约束的GPS/BDS单历元姿态解算算法研究

研究基于GNSS信号的实时载体动态姿态测量算法具有重要意义,多频多模姿态测量算法是目前的研究热点和难点。本文提出一种基于GPS L1/L2和BDS B1三频点观测数据进行联合定姿的新算法,可实现单历元整周模糊度解算,且该算法对周跳不敏感,克服了单频点定姿可靠性差、精度低的缺点。针对多频多模观测时天线相位中心的差异性问题,采用基于加权基线长度约束和上下边界函数的方法实现整周模糊度搜索空间的压缩,提高了整周模糊度解算的效率。最后基于实际测试数据评估定姿精度,实验表明,采用L1/L2/B1三频点联合估计,航向角和俯仰角的精度可达0.1?/m和0.2?/m,比单频观测的精度高约2倍。     

双星定位系统定姿的建模与仿真研究

以卫星模拟器为基础,介绍了一种双星定位系统定姿的基本原理,以卫星模拟器作为基准得出对应的三个双差观测方程,并且应用长短基线法和序列优化法求解整周模糊度,仿真结果表明,应用双星定位系统进行定姿是可行的.     

多天线/GPS光纤陀螺IMU组合车载定姿系统研究

利用GPS多天线定姿系统与低成本光纤陀螺IMU组合,以PC104作为组合导航计算平台,采用重调式松散组合算法,构建了低成本、高精度、高可靠性的车载航姿保持系统,并成功应用于移动卫星通讯系统。经测试,组合系统静态初始化时间小于2min,动态定姿精度优于0.1度,更新率为100Hz。该项技术可进一步拓展应用于舰载、机载等运动平台,前景可观。     

绳系网捕系统的定位与测姿方法研究

基于双目视觉原理,建立了空间目标的三维坐标计算模型,利用安装在捕获端的摄像头对主星进行观测,建立了捕获端定姿方法.仿真算例验证了所提方法能够以较高的测量精度实现定位和测姿,可以满足绳系卫星捕获端的姿态确定精度需求.     

惯性+星光折射定位组合导航技术研究

由于现有惯性器件精度水平有限,纯惯性导航误差较大,因此需要采用组合导航的方式来提高导航精度。目前,全自主组合导航方式中传统的惯性+星光定姿组合导航方法只能实现定姿,不能实现定位,无法修正加速度表测量误差引起的惯性导航误差,故在精度上可提升空间有限。为此,提出了一种惯性+星光折射定位组合导航方法,重点从星光折射定位原理、大气折射模型、非线性滤波和选星策略几个方面进行论证及分析。通过理论分析与数学仿真相结合的手段,验证了星光折射定位原理的正确性及工程可行性,可将自主导航精度提升至100m,从而为进一步提高自主导航精度提供了一种技术途径。     

导航卫星的短弧运动学定轨

导航卫星在姿轨控和轨道恢复期间,由于观测数据有限,传统的统计定轨理论难以实现导航卫星精密定轨。本文尝试采用一种不依赖轨道动力学的、新的运动学定轨方法来处理短弧和复杂动力学过程中的定轨,提出了基于多项式拟合的短弧运动学定轨算法,并提出2种不同的实现方案。该算法充分利用了高采样率的测轨数据,减少了结果的噪声,其优点在于不需要长时间累积测轨数据,可以实现近实时快速计算,克服了动力学法定轨发散和单点定位无法获得卫星速度信息等不足。对COMPASS M-01导航卫星实测数据的处理表明,10min左右短弧运动学定轨的位置精度可以优于10m,速度精度优于4cm/s,满足了短弧跟踪条件下RDSS对卫星轨道精度的要求,实现了短弧跟踪条件下卫星精密定轨,但从轨道预报精度来看,该方法仅仅适用于短期预报。     

视觉辅助惯性定位定姿技术研究

在利用视觉系统辅助捷联惯性导航系统( SINS)进行定位定姿时,由于两者输出的位置表示方法不同,在信息融合时会存在匹配问题。以相对地理坐标系作为定位定姿系统的导航坐标系,重新对SINS进行了力学编排,分析了其误差传递特性,建立了相对地理坐标系下的状态方程模型,并利用Kalman滤波器实现了视觉辅助惯性定位定姿算法。仿真结果表明,方法避免了信息融合时位置匹配问题,同时降低了系统的计算量,满足了定位定姿系统的精度要求。     

基于PnP和自适应线性卡尔曼滤波的实时位姿估计

针对实时位姿估计中扩展卡尔曼滤波(EKF)线性化引入非线性误差和依赖已知噪声分布的缺点,提出一种基于PnP的自适应线性卡尔曼滤波位姿估计求解方法。将PnP位姿估计求解策略引入卡尔曼滤波观测方程,通过对动态方程误差统计参数实时估计,自适应调节卡尔曼滤波递推参数。所提算法求解精度高,固定了观测方程的观测向量维度,提高了算法实用性。通过仿真试验,比较了该算法与EKF的位姿估计精度,通过量化误差分析,证明了该方法可以提高三维运动位姿估计精度,也验证了该方法的有效性。     

两种多天线GNSS动态定姿方法的比较

针对移动载体对姿态的需求,对两种多天线GNSS动态定姿方法,即直接法和最小二乘迭代法进行了研究.分析了定姿的原理,给出了姿态解算模型.基于车载四天线GNSS的实测数据,分别用两种方法进行了姿态解算,并用同一运动平台高精度惯导给出的姿态作为参考值,对两种定姿方法的精度和可靠性进行了分析和比较.     

航天发射任务星箭分离前调姿段测轨数据定初轨精度分析

在对星箭分离前调姿段各类测轨数据的测量机理及其误差特性研究的基础上,通过仿真数据和实战任务数据计算,分析了调姿段各类测轨数据的常用定轨方法的定轨精度,给出了定轨时各类数据的使用方法和定轨结果的优选原则。     

跨流域高超声速绕流Boltzmann模型方程并行算法

通过对Boltzmann方程碰撞积分进行模型化处理,提出了统一描述各流域复杂高超声速流动输运现象的气体分子速度分布函数控制方程,使用离散速度坐标法对分布函数方程所依赖的速度空间离散降维,构造出直接求解分子速度分布函数的气体动理论耦合迭代数值格式,研制了复杂飞行器高超声速绕流气动热力学计算模型。基于对气体动理论数值计算方法内在并行性、变量依赖关系、数据通信与并行可扩展性的分析研究,使用区域分解并行化方法提出了新型的气体动理论数值算法并行方案;研究了数据的并行分布与并行执行特征,开展了大规模的并行化程序设计,构造了可稳定运行于成千上万CPU的高性能并行算法,用以模拟各流域复杂飞行器的高超声速绕流问题。以稀薄流到连续流环境下不同Knudsen数、不同马赫数的可重复使用类球锥卫星体及翼身组合复杂飞行器等气动力、热绕流问题为研究对象展开大规模并行计算,并进行算法验证,所得计算结果与理论分析、直接模拟蒙特卡罗方法(DSMC)的模拟值及有关实验数据吻合较好,揭示了飞行器跨流域高超声速下的复杂流动机理与变化规律,提供了一条能够可靠模拟高超声速飞行器跨流域气动力及热问题的统一的算法应用研究途径。     

μ理论在电液负载模拟器中的应用

 研究μ理论在电液负载模拟器中的应用，提出电液负载模拟器的鲁棒控制策略。电液负载模拟器是一个复杂的机-电-液复合系统，且是一个强耦合、时变受控对象。综合考虑参数变化、模型变动和干扰等不确定性的影响，利用μ综合控制理论设计电液负载模拟器的鲁棒力控制器，并通过μ分析使用鲁棒力控制器时系统的鲁棒稳定性和鲁棒性能。给出使用鲁棒力控制器和经典力控制器时的实验结果，实验结果表明所设计鲁棒力控制器的有效性和优越性。     

基于圆型限制性三体问题模型的行星卫星逃逸能量研究

 基于由飞行器、行星及其卫星组成圆型限制性三体问题模型，通过庞加莱映射的方法，研究了飞行器从行星卫星附近逃逸的问题。在Jacobi常数确定的前提下，通过逆向积分，飞行器从L1或L2点附近返回近月点，得到近月点速度出发速度。研究结果表明绕飞L1点和L2点逃逸行星卫星需要的最低能量是不同的，从月球表面逃逸所需的速度脉冲分别比开普勒算法节省46.5m/s和42.3m/s，且均小于Villac等人在Hill模型下得到38.9m/s，从而改进了Villac等人的相关工作，同时也给出了从太阳系主要行星卫星表面逃逸所需的最小能量。     

Model Development and Adaptive Imbalance Vibration Control of Magnetic Suspended System

对星载磁悬浮单框架控制力矩陀螺,建立其转子的平动与转动的动力学方程。所建模型反映了转子的动、静不平衡特性,以及转子运动与框架、星体运动的耦合关系。模型是主动磁悬浮控制与动框架效应分析的基础。对动、静不平衡量未知的转子,设计了自适应对中控制器。在分散PD、比例交叉反馈控制器与高低通滤波器的基础上,通过动、静不平衡量的辨识与补偿控制,使转子绕其惯量主轴旋转,衰减角动量交换执行机构高速转子因不平衡而对基座产生的干扰力,消除星上主要颤振源,达到降低卫星姿态抖动的目的。     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

Love Waves in Layered Graded Composite Structures with Imperfectly Bonded Interface

Theoretical analysis and numerical calculations of Love wave propagation in layered graded composites with imperfectly bonded interface are described in this paper. On the basis of WKB method, the approximate analytic solutions for Love waves are obtained. By the interface shear spring model, the dispersion relations for Love waves in layered graded composite structures with rigid, slip, and imperfectly bonded interfaces are given, and the effects of the interface conditions on the phase velocities of Love waves in SiC/Al lay- ered graded composites are discussed. Numerical analysis shows that the phase velocity decreases when the defined flexibility parameter is greater. For the general imperfectly bonded interface, the phase velocity changes in the range of the velocities for the rigid and slip interface conditions.     

Experimental Investigation on Performance of Pulse Detonation Rocket Engine Model

The PDRE test model used in these experiments utilized kerosene as the fuel, oxygen as oxidizer, and nitrogen as purge gas. The solenoid valves were employed to control intermittent supplies of kerosene, oxygen and purge gas. PDRE test model was 50 mm in inner diameter by 1.2 m long. The DDT （deflagration to detonation transition） enhancement device Shchelkin spiral was used in the test model. The effects of detonation frequency on its time-averaged thrust and specific impulse were experimentally investigated. The obtained results showes that the time-averaged thrust of PDRE test model was approximately proportional to the detonation frequency. For the detonation frequency 20 Hz, the time-averaged thrust was around 107 N, and the specific impulse was around 125 s. The nozzle experiments were conducted using PDRE test model with three traditional nozzles. The experimental results obtained demonstrated that all of those nozzles could augment the thrust and specific impulse. Among those three nozzles, the convergent nozzle had the largest increased augmentation, which was approximately 18%, under the specific condition of the experiment.     

Compression Creep Behavior of High Volume Fraction of SiC Particles Reinforced Al Composite Fabricated by Pressureless Infiltration

The compression creep deformation of the high volume fraction of SiC particles reinforced Al-Mg-Si composite fabricated by pressure-less infiltration was investigated. The experimental results show that the creep stress exponents are very high at temperatures of 673 K, 723 K and 773 K, and if taking the threshold stress into account, the true stress exponent of minimum creep strain rate is still approximately 5, although the volume fraction of reinforcements is very high. The creep strain rate in the high volume fraction rein- forced aluminum alloy matrix composites is controlled by matrix lattice diffusion. It is found that the creep-strengthening effect of high volume fraction of silicon carbide particles is significant, although the particles do not form effective obstacles to dislocation motion.     

高超声速飞行器高温流场数值模拟面临的问题

随着高超声速飞行器目标光辐射和电磁散射特性研究的发展和深入,高温流场特性日益引起人们的关注。由于高温流场特性研究中涉及到非常多的复杂气动现象,如气动加热、烧蚀、辐射、燃烧、化学反应以及湍流等,因此其数值模拟面临着诸多挑战。这里基于连续流计算流体力学(CFD)技术和稀薄气体蒙特卡罗直接仿真(DSMC)方法,从化学物理模型建模、方法稳定性与数值求解效率出发,分析了高超声速飞行器外部绕流、尾迹和发动机喷焰三方面的流场特性数值模拟在不同弹道、热防护手段和飞行流域环境下所面临的问题。在此基础上提出了数值求解技术和化学物理模型建模今后需要发展的方向,为有效提高高超声速高温流场特性数值模拟效率、增加流场特性预测精度提供了指导,从而为研究流场对高超声速飞行器目标光辐射和电磁散射特性影响提供有效的基础数据。     

Adaptive Control of Helicopter Ground Resonance with Magnetorheological Damper

The methodology for adaptive control of helicopter ground resonance with magnetorheological （MR） damper is presented. The adaptive inverse control method is used to control the output damping force of MR damper and the range of the damping force is given. Through the adaptive inverse control, the damping force of MR damper is fit to a desired damping force. With the background of applying MR damper to control of helicopter ground resonance, a model of loss force and an adaptive arithmetic for stabilization of the coupled rotor/fuselage system are presented. The simulation shows that the controller presented in this paper can stabilize the rotor/fuselage coupling system quickly and control the helicopter ground resonance effectively.