Design and experimental study of a micro-groove grinding wheel with spray cooling effect

The effectiveness of grinding fluid supply has a crucial impact on grinding quality and efficiency in high speed grinding. In order to improve the cooling and lubrication, through in-depth research of self-inhaling internal cooling method and intermittent grinding mechanism, a new spray cooling method used in high speed grinding is proposed. By referring to the structure of bowl- shaped dispersion disk, the grinding wheel matrix with atomization ability is designed; through studying heat transfer of droplet collision and the influence of micro-groove on the boiling heat transfer, grinding segment with micro-groove is designed to enhance the heat flux of coolant and achieve maximum heat transfer between droplets and grinding contact zone. High-speed grinding experiments on GH4169 with the developed grinding wheel are carried out. The results show that with the micro-groove grinding wheel just 5.4% of pump outlet flow rate and 0.5% of spindle energy is needed to reduce the grinding temperature to 200℃, which means the developed grinding wheel makes cooling high efficient and low energy consuming.     

Developing a novel radial ultrasonic vibration-assisted grinding device and evaluating its performance in machining PTMCs

Particle-reinforcing titanium matrix composites(PTMCs) exhibit the sharp raising applications in modern industries owing to its extraordinary physical and mechanical properties. However, the poor grindability and unstable grinding processes due to the existence of TiC particles and TiB short fibres inside PTMCs, leading to the sudden grinding burn and low material removal rate.In this work, a novel radial ultrasonic vibration-assisted grinding(RUVAG) device with a special cross structure was dev...     

TC4钛合金高效磨削加工用环形热管砂轮的研制

针对航空航天高强韧性难加工材料TC4钛合金在磨削加工中存在磨削温度高而导致工件表面烧伤的问题,提出利用热管换热技术冷却磨削弧区的新方法.分析了环形热管砂轮在加工中对磨削弧区的强化换热原理,并设计制作出能够用于磨削加工的环形热管砂轮,同时实现了对砂轮基体内环形管腔的密封、抽真空、精确注液与机械式真空封口.最后,在相同磨削工艺条件下,使用环形热管砂轮和无热管砂轮进行TC4钛合金缓进给深切磨削对比试验,验证了环形热管砂轮对磨削弧区温度的控制效果.试验结果表明:设计制作的环形热管砂轮在TC4钛合金高效磨削过程中可以有效降低磨削温度,避免工件表面出现烧伤.     

Thermomechanical coupling effect on characteristics of oxide film during ultrasonic vibration-assisted ELID grinding ZTA ceramics

Ultrasonic vibration-assisted ELID (UVA-ELID) grinding is utilized as a novel and highly efficient processing method for hard and brittle materials such as ceramics. In this study, the UVA-ELID grinding ZTA ceramics is employed to investigate the influence of thermomechanical loading on the characteristics of oxide film. Based on the fracture mechanics of material, the model of internal stress for oxide film damage is proposed. The thermomechanical loading is composed of mechanical force and the thermal stress generating from grinding temperature. The theoretical model is established for the mechanical force, thermal stress and internal stress respectively. Then the finite element analysis method is used to simulate the theoretical model. The mechanical force and grinding temperature is measured during the actual grinding test. During the grinding process, the effect of grinding wheel speed and grinding depth on the thermomechanical force and the characteristics of oxide film is analyzed. Compared with the conventional ELID (C-ELID) grinding, the mechanical force decreased by 25.6% and 22.4% with the increase of grinding wheel speed and grinding depth respectively, and the grinding temperature declined by 10.7% and 12.8% during the UVA-ELID grinding. The thermal stress in the latter decreased by 16.3% and 20.8% respectively, and internal stress reduced by 12.3% and 15.6%. It was experimentally found that the topographies of oxide layer on the surface of the wheel and the machined surface in the latter was better than that in the former. The results indicate that the action of ultrasonic vibration establish a significant effect on the processing. Subsequently, it should be well considered for future reference when processing the ZTA ceramics.     

钛合金TC4电火花诱导可控烧蚀高效磨削技术研究

利用大部分金属尤其是难加工金属的可燃特性,开发一种针对难加工金属材料的新加工工艺——电火花(EDM)诱导可控烧蚀高效磨削技术。采用开槽导电砂轮进行磨削加工,首先利用导电区域与加工材料产生电火花诱导放电并通入助燃氧气,使材料表面产生电火花引燃烧蚀并软化,然后将已烧蚀和软化的材料磨除,对钛合金TC4进行烧蚀磨削试验,并与常规电火花磨削和机械磨削进行对比,分析了材料去除率(RMM)、表面质量和机床主轴电机功率变化等指标。结果表明,在试验条件下,烧蚀磨削在放电利用率提高的同时可获得表面粗糙度为0.59 μm的加工表面,与机械磨削的表面粗糙度值相近,而相同条件下电火花磨削的表面粗糙度为1.29 μm。由于烧蚀后产生了软化层,在切深小于软化层厚度的条件下,相对于电火花磨削和机械磨削状况,烧蚀磨削主轴电机功率相比空载时的增加值分别降低了95.2%和96.8%。此工艺方法可大大提高难加工材料的可磨削性能。     

杯形砂轮铣磨二次曲面的数学模型与误差分析

运用几何方法,推导了杯形砂轮铣磨二次曲面的数学模型和砂轮轨迹的计算公式。分析了加工残留误差,砂轮磨损以及砂轮倾角误差对面形精度的影响。     

Feasibility study of creep feed grinding of 300M steel with zirconium corundum wheel

The ultrahigh strength 300M steel has been commonly used in the manufacture of aircraft landing gear and rotor shaft parts due to its excellent mechanical properties. Creep feed grinding is one of the essential operations during the whole component manufacturing processes. In this work, the feasibility of creep feed grinding of 300M steel by using the hard zirconium corundum wheel was theoretically and experimentally evaluated. A variety of responses including grinding forces, temperature fields...     

航发涡轮叶片气膜孔的磨削加工实验

针对目前航空发动机涡轮叶片气膜孔加工精度低和重熔层难去除的问题,提出了"电火花打孔、磨削扩孔"的新型气膜孔加工工艺,研制出小孔磨削专用微细CBN砂轮并对电火花气膜孔进行了磨削工艺实验。实验结果表明:经磨削加工后气膜孔圆度降低50.9%,孔径尺寸标准差降低90.7%,表面粗糙度降低65.9%,重熔层被全部去除,证明了航发涡轮叶片气膜孔磨削加工的可行性。     

激光宏观结构化金刚石砂轮磨削氧化铝工艺

为了研究砂轮表面结构化对砂轮磨削性能的影响,利用脉冲激光对树脂结合剂金刚石砂轮进行了表面宏观结构化。采用6种不同类型的金刚石砂轮表面宏观结构进行了氧化铝的磨削实验,建立了激光宏观结构化金刚石砂轮的磨削力模型,比较了6种不同激光宏观结构化金刚石砂轮与非结构化砂轮在不同磨削参数下磨削力的差异,分析了砂轮制造后的表面形貌与结构化砂轮的磨损特性。实验结果表明,砂轮宏观结构化对磨削性能有很大影响,激光宏观结构化砂轮的磨削力可以减小2. 5%~24. 5%,砂轮结构化后的表面形貌出现石墨化现象;宏观结构化砂轮沟槽边缘磨损加剧,但沟槽磨损并没有明显加快宏观结构化砂轮的磨损。     

钛合金TC4的超硬磨料柔性抛光轮数控抛光试验研究

航空发动机叶片钛合金材料在数控磨抛加工中容易发生烧伤及黏附现象,针对常用的TC4材料开展了超硬磨料柔性抛光轮数控抛光试验研究。分析了超硬磨料柔性抛光轮抛光参数中转速、进给速度、预压量及行距对抛光去除深度及抛光后试件表面粗糙度的影响规律并通过正交试验分析了各抛光参数影响的主次关系。确认了钛合金试件抛光表面黏附物质成分,并同时分析了表面黏附物的形成原理。给出了TC4钛合金材料在超硬磨料柔性抛光轮数控抛光过程中工艺参数的选择策略,为TC4材料的航空发动机叶片和整体叶盘在超硬磨料柔性抛光轮数控抛光过程中提供理论依据和技术基础。     

Comparative investigation on high-speed grinding of TiCp/Ti–6Al–4V particulate reinforced titanium matrix composites with single-layer electroplated and brazed CBN wheels

In order to develop the high-efficiency and precision machining technique of Ti Cp/Ti–6Al–4V particulate reinforced titanium matrix composites(PTMCs), high-speed grinding experiments were conducted using the single-layer electroplated cubic boron nitride(CBN) wheel and brazed CBN wheel, respectively. The comparative grinding performance was studied in terms of grinding force, grinding temperature, grinding-induced surface features and defects. The results display that the grinding forces and grinding temperature obtained with the brazed CBN wheel are always lower than those with the electroplated CBN wheel. Though the voids and microcracks are the dominant grinding-induced surface defects, the brazed CBN wheel produces less surface defects compared to the electroplated wheel according to the statistical analysis results. The maximum materials removal rate with the brazed CBN wheel is much higher than that with the electroplated one. All above indicate that the single-layer brazed CBN super-abrasive wheel is more suitable for high-speed grinding of PTMCs than the electroplated counterpart.     

钛合金风扇叶片磨抛加工性能试验研究

针对钛合金风扇叶片磨抛加工中砂轮易磨损、工件表面易烧伤的问题,开展了钛合金材料磨抛加工性试验研究,主要考察砂轮选型、磨抛工艺参数等关键因素对钛合金材料磨抛加工性的影响,并对试验结果进行了分析研究。试验结果表明,在保证工件表面加工质量(R_a0.8μm,表面无烧伤)的前提下,普通磨料砂轮GC46L10V磨抛加工钛合金的材料去除率和磨抛比分别可达5000mm~3/min和2.5,超硬磨料陶瓷结合剂CBN砂轮磨抛加工钛合金的材料去除率和磨抛比分别可达2000mm~3/min和4。基于研究结果,针对钛合金风扇叶片开展了砂带磨抛加工验证试验,工件加工质量良好。     

基于碟形砂轮磨齿的面齿轮包络残差研究

介绍了采用碟形砂轮磨削面齿轮的原理及过程,研究了齿廓包络和齿宽包络两种包络方式产生包络残差的机理.分别建立了两种加工方式下包络残差的计算模型和方法,并研究了所产生包络残差的特点.通过数值算例分析了包络过程中刀具周向进给角度、齿宽方向进给量以及碟形砂轮外径对齿面包络残差的影响规律.计算结果表明:齿宽包络比齿廓包络具有更高的效率.进行了以齿廓包络方式的面齿轮磨齿加工实验,当刀具周向进给角度分别取为2°,1°,0.5°及0.2°时,齿面表面粗糙度逐渐明显提高,齿面磨削加工印痕的数目和方向与包络仿真计算结果一致.初步证明根据包络残差计算结果选取合适的进给量参数,可以保证面齿轮磨齿加工的表面粗糙度水平并能提高加工效率.      

飞行器鼻锥凹腔-发散组合冷却数值模拟

尖锐鼻锥冷却方案是可复用式航天飞行器研究领域一个十分重要的课题。传统发散冷却虽然可以有效降低鼻锥结构温度,但是由于驻点外极高的热流、压力,会出现驻点冷却效果差的问题。迎风凹腔结构是一种针对鼻锥驻点区域的减阻防热方案,尖锐唇口的分流作用可以使附近压力、热流降低。因此,提出一种新型冷却结构——凹腔-发散组合冷却,利用迎风凹腔结构对驻点的强化冷却解决发散冷却中驻点难以冷却的问题。以楔形鼻锥为物理模型,对发散冷却、迎风凹腔结构和凹腔-发散冷却3种冷却结构进行数值模拟,并和无冷却的纯鼻锥结构进行对比。结果表明,与传统发散冷却相比,使用凹腔-发散组合冷却可以使结构温度峰值下降16.8%;与没有冷却的纯鼻锥模型相比,鼻锥头部圆弧段表面平均温度降幅可达64%,证实了这种新型冷却结构的可行性和高效性。     

高纯钨磨削加工试验研究

为探究适用于高纯钨磨削加工的砂轮,使用80~#绿碳化硅砂轮和金刚石砂轮开展磨削对比试验,从工件表面粗糙度角度评价上述两种砂料对高纯钨磨削加工表面的影响。试验结果表明,绿碳化硅砂轮对应的工件得到了更理想的表面粗糙度。使用绿碳化硅砂轮开展工艺试验,分析在不同磨削参数下加工表面粗糙度的变化趋势,以此为依据对高纯钨磨削加工工艺参数进行评价与优化。综合考虑加工表面粗糙度以及加工效率,得出适合于钨磨削加工的参数为砂轮线速度v_s=23m/s、磨削深度a_p=8μm、工作台进给速度v_w=10m/min,该参数下得到的表面粗糙度均值为0.336μm。     

Grinding performance evaluation of porous composite-bonded CBN wheels for Inconel 718

For high-efficiency grinding of difficult-to-cut materials such as titanium and nickel alloys, a high porosity is expected and also a sufficient mechanical strength to satisfy the function.However, the porosity increase is a disadvantage to the mechanical strength. As a promising pore forming agent, alumina bubbles are firstly induced into the abrasive layer to fabricate porous cubic boron nitride（CBN） wheels. When the wheel porosity reaches 45%, the bending strength is still high up to 50 MPa with modified orderly pore distribution. A porous CBN wheel was fabricated with a total porosity around 30%. The grinding performance of the porous composite-bonded CBN wheel was evaluated in terms of specific force, specific grinding energy, and grinding temperature, which were better than those of the vitrified one under the same grinding conditions. Compared to the vitrified CBN wheel, clear straight cutting grooves and less chip adhesion are observed on the ground surface and there is also no extensive loading on the wheel surface after grinding.     

缓磨烧伤过程的计算机仿真研究

在关于缓磨时的磨削热 ,接触弧区换热过程以及工件表层非稳态温度场的深入研究的基础上 ,构造了一可用于计算缓磨烧伤前后工件表层温度场畸变历程的数学模型 ,并据此完成了关于缓磨烧伤过程的计算机仿真研究 ,仿真结果与实际吻合良好 ,它率先阐明了缓磨烧伤的热机理并且证明了缓磨烧伤是一具有明显前兆特征的典型渐变过程     

新型刚玉砂轮磨削GH4169镍基高温合金的性能评价研究

镍基高温合金是航空发动机部件的常用材料,其磨削加工存在工具损耗严重、寿命短等难题。针对3种新研制的刚玉砂轮(分别为粒度60#的微晶和单晶混合磨料砂轮、粒度60#的单晶刚玉砂轮,以及粒度70#的单晶刚玉砂轮),开展了GH4169镍基高温合金材料的磨削试验,从磨削力、磨削温度、砂轮磨损以及表面粗糙度等方面对3种砂轮的磨削性能进行了评价。结果表明,3种砂轮磨削GH4169材料在砂轮磨损和表面粗糙度方面未表现出明显差异,而通过对磨削力和磨削温度的综合评价发现粒度60#的单晶刚玉砂轮的磨削性能更优。3种砂轮磨削GH4169材料的磨削比在0.5~3之间。在正常磨削条件下,3种砂轮的磨削表面粗糙度Ra小于0.4μm。同时发现,砂轮磨损(主要包括磨粒的破碎和脱落)是造成磨削表面缺陷形成的重要原因。     

磁流变弹性体砂轮抛光镍基高温合金表面完整性研究

为了改善磨削后镍基高温合金GH4169的表面完整性,本文采用磁流变弹性体砂轮对镍基高温合金GH4169进行抛光试验研究。首先,通过模压成型的方法制备了磁流变弹性体砂轮,并对其表面微观形貌及不同磁场强度下的硬度进行了表征。其次将制备出的磁流变弹性体砂轮用于对镍基高温合金GH4169的抛光工艺试验中,并讨论抛光工艺参数中磁场强度对镍基高温合金表面完整性的影响。试验结果表明：在一定的磁场强度范围内,零件抛光后的表面粗糙度和显微硬度随着磁场强度的增大而减小,同时增大磁场强度也有利于改善零件的表面形貌,减少砂轮的磨损量,降低零件磨削后的亚表面损伤层厚度。     

Analysis of grinding mechanics and improved grinding force model based on randomized grain geometric characteristics

Too high grinding force will lead to a large increase in specific grinding energy, resulting in high temperature in grinding zone, especially for the aerospace difficult cutting metal materials,seriously affecting the surface quality and accuracy. At present, the theoretical models of grinding force are mostly based on the assumption of uniform or simplified morphological characteristics of grains, which is inconsistent with the actual grains. Especially for non-engineering grinding wheel,most g...