TC4钛合金高效磨削加工用环形热管砂轮的研制

针对航空航天高强韧性难加工材料TC4钛合金在磨削加工中存在磨削温度高而导致工件表面烧伤的问题,提出利用热管换热技术冷却磨削弧区的新方法.分析了环形热管砂轮在加工中对磨削弧区的强化换热原理,并设计制作出能够用于磨削加工的环形热管砂轮,同时实现了对砂轮基体内环形管腔的密封、抽真空、精确注液与机械式真空封口.最后,在相同磨削工艺条件下,使用环形热管砂轮和无热管砂轮进行TC4钛合金缓进给深切磨削对比试验,验证了环形热管砂轮对磨削弧区温度的控制效果.试验结果表明:设计制作的环形热管砂轮在TC4钛合金高效磨削过程中可以有效降低磨削温度,避免工件表面出现烧伤.     

Suppression of Surface Burn in Grinding of Titanium Alloy TC4 Using a Self-inhaling Internal Cooling Wheel

Based on analysis of surface average temperature and burn degree, this article obtains the threshold temperature of surface burn in grinding titanium alloy with cup wheels. Meanwhile, the impact of the burn degree on the metallographic structure of workpiece surface and metallurgical phase transformations is investigated. In order to reduce the grinding temperature and improve the grinding efficiency, a self-inhaling structure cup segmented wheel is developed to generate internal cooling effect. The internal cooling technology is compared with traditional cooling conditions in the grinding experiments on TC4 (Ti-6Al-4V). The results indicate that the self-inhaling internal cooling wheel can reduce the grinding surface temperature by 30% or more, and the grinding efficiency doubles. Utilizing water-based semi-synthetic coolant, the segmented wheel with the self-inhaling structure can further reduce the grinding temperature by about 50%.     

Grindability and Surface Integrity of Cast Nickel-based Superalloy in Creep Feed Grinding with Brazed CBN Abrasive Wheels

The technique of creep feed grinding is most suitable for geometrical shaping, and therefore has been expected to improve effectively material removal rate and surface quality of components with complex profile. This article studies experimentally the effects of process parameters (i.e. wheel speed, workpiece speed and depth of cut) on the grindability and surface integrity of cast nickel-based superalloys, i.e. K424, during creep feed grinding with brazed cubic boron nitride (CBN) abrasive wheels. Some important factors, such as grinding force and temperature, specific grinding energy, size stability, surface topography, microhardness and microstructure alteration of the sub-surface, residual stresses, are investigated in detail. The results show that during creep feed grinding with brazed CBN wheels, low grinding temperature at about 100 °C is obtained though the specific grinding energy of nickel-based superalloys is high up to 200-300 J/mm³. A combination of wheel speed 22.5 m/s, workpiece speed 0.1 m/min, depth of cut 0.2 mm accomplishes the straight grooves with the expected dimensional accuracy. Moreover, the compressive residual stresses are formed in the burn-free and crack-free ground surface.     

Analysis of grinding mechanics and improved grinding force model based on randomized grain geometric characteristics

Too high grinding force will lead to a large increase in specific grinding energy, resulting in high temperature in grinding zone, especially for the aerospace difficult cutting metal materials,seriously affecting the surface quality and accuracy. At present, the theoretical models of grinding force are mostly based on the assumption of uniform or simplified morphological characteristics of grains, which is inconsistent with the actual grains. Especially for non-engineering grinding wheel,most g...     

Thermomechanical coupling effect on characteristics of oxide film during ultrasonic vibration-assisted ELID grinding ZTA ceramics

Ultrasonic vibration-assisted ELID (UVA-ELID) grinding is utilized as a novel and highly efficient processing method for hard and brittle materials such as ceramics. In this study, the UVA-ELID grinding ZTA ceramics is employed to investigate the influence of thermomechanical loading on the characteristics of oxide film. Based on the fracture mechanics of material, the model of internal stress for oxide film damage is proposed. The thermomechanical loading is composed of mechanical force and the thermal stress generating from grinding temperature. The theoretical model is established for the mechanical force, thermal stress and internal stress respectively. Then the finite element analysis method is used to simulate the theoretical model. The mechanical force and grinding temperature is measured during the actual grinding test. During the grinding process, the effect of grinding wheel speed and grinding depth on the thermomechanical force and the characteristics of oxide film is analyzed. Compared with the conventional ELID (C-ELID) grinding, the mechanical force decreased by 25.6% and 22.4% with the increase of grinding wheel speed and grinding depth respectively, and the grinding temperature declined by 10.7% and 12.8% during the UVA-ELID grinding. The thermal stress in the latter decreased by 16.3% and 20.8% respectively, and internal stress reduced by 12.3% and 15.6%. It was experimentally found that the topographies of oxide layer on the surface of the wheel and the machined surface in the latter was better than that in the former. The results indicate that the action of ultrasonic vibration establish a significant effect on the processing. Subsequently, it should be well considered for future reference when processing the ZTA ceramics.     

原位自生TiB_2/Al复合材料磨削表面质量研究

原位自生TiB_2/Al复合材料具有密度小,比强度高,比模量大等特点,在航空航天领域具有广泛的应用前景。为探索原位自生TiB_2/Al复合材料的磨削加工性能,选用单晶刚玉SA砂轮、白刚玉WA砂轮和CBN砂轮在不同磨削参数下对TiB_2/Al复合材料进行磨削试验。首先研究了砂轮材质、转速、工件速度、磨削深度对工件表面粗糙度的影响规律;其次通过对工件表面形貌、磨屑形态、砂轮磨损的观测分析,探索了原位自生TiB_2/Al复合材料磨削表面成形机制;最后基于试验数据,给出了TiB_2/Al复合材料磨削工艺参数优选域。本研究可为颗粒增强金属基复合材料磨削加工提供基础理论支撑。     

Grinding performance evaluation of porous composite-bonded CBN wheels for Inconel 718

For high-efficiency grinding of difficult-to-cut materials such as titanium and nickel alloys, a high porosity is expected and also a sufficient mechanical strength to satisfy the function.However, the porosity increase is a disadvantage to the mechanical strength. As a promising pore forming agent, alumina bubbles are firstly induced into the abrasive layer to fabricate porous cubic boron nitride（CBN） wheels. When the wheel porosity reaches 45%, the bending strength is still high up to 50 MPa with modified orderly pore distribution. A porous CBN wheel was fabricated with a total porosity around 30%. The grinding performance of the porous composite-bonded CBN wheel was evaluated in terms of specific force, specific grinding energy, and grinding temperature, which were better than those of the vitrified one under the same grinding conditions. Compared to the vitrified CBN wheel, clear straight cutting grooves and less chip adhesion are observed on the ground surface and there is also no extensive loading on the wheel surface after grinding.     

Feasibility study of creep feed grinding of 300M steel with zirconium corundum wheel

The ultrahigh strength 300M steel has been commonly used in the manufacture of aircraft landing gear and rotor shaft parts due to its excellent mechanical properties. Creep feed grinding is one of the essential operations during the whole component manufacturing processes. In this work, the feasibility of creep feed grinding of 300M steel by using the hard zirconium corundum wheel was theoretically and experimentally evaluated. A variety of responses including grinding forces, temperature fields...     

开槽砂轮缓磨时射流冲击强化换热的研究

提出了运用磨削弧区强化换热技术开发高效磨削潜力的创新构想,并在开槽砂轮的基础上研制开发了能够实现磨削弧区沿砂轮径向定向高压水射流冲击强化换热的新型磨削液供液装置;完成了关于开槽砂轮缓磨时弧区定向高压水射流冲击强化换热效果的理论计算和实验研究,计算结果与实验结果基本吻合。     

Interference and grinding characteristics in ultra-precision grinding of thin-walled complex structural component using a ball-end grinding wheel

As for ultra-precision grinding of difficult-to-process thin-walled complex components with ball-end grinding wheels, interference is easy to occur. According to screw theory and grinding kinematics, a mathematical model is established to investigate the interference and grinding characteristics of the ball-end wheel. The relationship between grinding wheel inclination angle, C axis rotation angle, grinding position angle and grinding wheel wear are analyzed. As the grinding wheel inclination angle increases, the C axis rotatable range decreases and the grinding position angle increases. The grinding position angle and wheel radius wear show a negative correlation with the C axis rotation angle. Therefore, a trajectory planning criteria for increasing grinding speed as much as possible under the premise of avoiding interference is proposed to design the grinding trajectory. Then grinding point distribution on the ball-end wheel is calculated, and the grinding characteristics, grinding speed and maximum undeformed chip thickness, are investigated. Finally, a complex structural component can be ground without interference, and surface roughness and profile accuracy are improved to 40.2 nm and 0.399 μm, compared with 556 nm and 3.427 μm before ultra-precision grinding. The mathematical model can provide theoretical guidance for the analysis of interference and grinding characteristics in complex components grinding to improve its grinding quality.     

旋转状态下涡轮叶片复合冷却结构

采用三维流固耦合换热计算研究了旋转状态下涡轮叶片冷却结构的复合冷却性能,讨论了辐射换热和转速对综合冷却效果的影响.结果表明:结构1叶根处出现局部高温区,低冷却效率范围大,叶片整体温度分布不均匀,结构2通过更合理的气膜流量分配提高了前缘附近冷却效率,降低了叶片表面最高温度,结构3采用内部蛇形通道使吸力面冷却效率显著提高,叶片整体冷却效率分布较为均匀；考虑壁面辐射换热时叶片表面温度升高,当表面发射率为1时局部温升超过50K,壁面辐射换热的影响不能被忽略；压力面综合冷却效率随转速增大而升高,3种结构的局部冷却效率最高分别能提升15.6%，13.4%和16.4%,吸力面上除弦中区冷却效率随转速升高有所降低外,其余位置冷却效率变化不大.      

离心力场下多孔介质中热驱动换热的实验

以涡轮叶片新型超级冷却技术的研究为背景,在具有冷却通道的新型冷却结构中加入多孔介质,用实验的方法,模拟了离心力场下该新型冷却结构的热驱动换热现象,并与无多孔介质的情况进行了比较。实验结果表明:随着旋转速度、热流密度和冷气进口速度的增大,装有多孔介质的新型冷却结构的热驱动换热能力逐渐增强。同时实验研究发现,加入多孔介质后该新型冷却结构比未加多孔介质时具有更好的换热效果。      

断续缓磨射流冲击强化磨削弧区换热的实验研究

通过深切缓磨时磨削烧伤机理的分析,提出高压射流冲击强化磨削弧区换热新构想,并通过断续缓磨射流侧向冲击弧区的磨削实验显示其换热效果．     

高纯钨磨削加工试验研究

为探究适用于高纯钨磨削加工的砂轮,使用80~#绿碳化硅砂轮和金刚石砂轮开展磨削对比试验,从工件表面粗糙度角度评价上述两种砂料对高纯钨磨削加工表面的影响。试验结果表明,绿碳化硅砂轮对应的工件得到了更理想的表面粗糙度。使用绿碳化硅砂轮开展工艺试验,分析在不同磨削参数下加工表面粗糙度的变化趋势,以此为依据对高纯钨磨削加工工艺参数进行评价与优化。综合考虑加工表面粗糙度以及加工效率,得出适合于钨磨削加工的参数为砂轮线速度v_s=23m/s、磨削深度a_p=8μm、工作台进给速度v_w=10m/min,该参数下得到的表面粗糙度均值为0.336μm。     

高马赫数涡轮发动机射流预冷特性研究

射流预冷涡轮基发动机在高空高马赫数工作时对冷却水和液氧具有迫切的需求。本文以气液相变冷却机制为切入点，开展高空模拟试验进气预冷段内水-液氧射流冷却的数值分析，考虑真实雾滴颗粒运动的热力现象，基于欧拉-拉格朗日多相流方法解析气液两相热质传输过程，分析水-液氧混合射流对高马赫数涡轮发动机预冷段内流动及换热特性的影响规律。结果表明，水-液氧射流雾化蒸发的效果具有即时性，基于水雾-水蒸汽比热大和汽化焓高的特点，水雾浓度对主流总温降和总压恢复占主导性；而液氧浓度有利于降低湿空气的热流密度。在射流浓度2%-8%时，预冷段总压降系数为0.84%-1.27%，总温降系数范围为2.15%-15.12%，即温降范围为12.92K-90.89K。为平衡高空高马赫数时冷却水和液氧的需求，需控制水-液氧的射流比例，液氧射流量建议小于60%的总射流浓度。在“40%水-60%液氧”的射流比例时预冷段内流动和传热特性达到局部最优。在发动机物理转速不变时，射流冷却后预冷段内湿空气来流质量流量增幅0.22%-9.39%，其中空气和水蒸气含量的贡献份额分别约为71.8%和28.2%。因此，射流预冷有利于涡轮发动机在高马赫数时具有更高的加速度。     

激光宏观结构化金刚石砂轮磨削氧化铝工艺

为了研究砂轮表面结构化对砂轮磨削性能的影响,利用脉冲激光对树脂结合剂金刚石砂轮进行了表面宏观结构化。采用6种不同类型的金刚石砂轮表面宏观结构进行了氧化铝的磨削实验,建立了激光宏观结构化金刚石砂轮的磨削力模型,比较了6种不同激光宏观结构化金刚石砂轮与非结构化砂轮在不同磨削参数下磨削力的差异,分析了砂轮制造后的表面形貌与结构化砂轮的磨损特性。实验结果表明,砂轮宏观结构化对磨削性能有很大影响,激光宏观结构化砂轮的磨削力可以减小2. 5%~24. 5%,砂轮结构化后的表面形貌出现石墨化现象;宏观结构化砂轮沟槽边缘磨损加剧,但沟槽磨损并没有明显加快宏观结构化砂轮的磨损。     

航发涡轮叶片气膜孔的磨削加工实验

针对目前航空发动机涡轮叶片气膜孔加工精度低和重熔层难去除的问题,提出了"电火花打孔、磨削扩孔"的新型气膜孔加工工艺,研制出小孔磨削专用微细CBN砂轮并对电火花气膜孔进行了磨削工艺实验。实验结果表明:经磨削加工后气膜孔圆度降低50.9%,孔径尺寸标准差降低90.7%,表面粗糙度降低65.9%,重熔层被全部去除,证明了航发涡轮叶片气膜孔磨削加工的可行性。     

ELID成形磨削实验研究与表面粗糙度预测

为了探究ELID成型磨削中磨削参数和电解参数对表面粗糙度的影响规律,基于未变形切屑厚度模型,考虑砂轮上磨粒出刃高度的随机性以及ELID磨削中氧化膜的影响,建立了针对ELID磨削的表面粗糙度预测模型。单因素实验研究了ELID成形磨削电源参数对表面粗糙度的影响规律,并探讨了电解电流与氧化膜厚度之间的关系。全因子实验以工件转速、砂轮转速和进给切深为影响因素,研究了磨削参数对表面粗糙度的影响规律,并对预测模型进行了验证。结果表明:磨削参数中,其他条件一定时,表面粗糙度随砂轮转速的增大而减小,随工件转速和切深的增大而增大;同时对于粗糙度的预测误差达到了8.75%,预测模型有效可靠。     

Simulation of the secondary air system of turbofan engines: Insights from 1D-3D modeling

Focusing on the internal flow and heat transfer analysis, a platform for the performance evaluation of the Secondary Air System (SAS) is developed. A multi-fidelity modeling technique has been developed in a turbofan engine model under different flight conditions. A turbine blade cooling model which integrates external heat transfer calculations and coolant side modeling with common components is proposed. In addition, the Computational Fluid Dynamics (CFD) method is selected to capture the complex flow field structure in the preswirl system. The validity of the SAS models is compared with publicly available data. An elaborately designed cooling system for the AGTF30 engine is analyzed through three main branches. It is found that the 1D-3D modeling technique can provide more accurate predictions of the SAS for the AGTF30 engine. The results demonstrate the versatility and flexibility of the SAS models, thereby indicating the capacity of meeting most of the demands of flow and thermal analysis of the SAS.     

基于数值模拟的内斜齿轮成形磨削 砂轮修形方法

针对内斜齿轮数控成形磨削中较难解决的磨削干涉问题,研究了内斜齿轮成形磨削的砂轮修形方法.在建立内斜齿轮成形磨削数学模型的基础上,用截圆法得到磨削内斜齿轮时砂轮与齿槽接触点所满足的条件方程组,通过牛顿迭代法解此方程组求出砂轮廓形.用数值法模拟出所求砂轮的实际磨削齿形并与理论渐开线齿形作比较,以检验磨削是否干涉及砂轮半径和安装角的选取是否正确.基于 Visual C++ 6.0 编制内斜齿轮砂轮修形及误差分析软件,通过仿真正确选择砂轮安装角、砂轮半径,并输出数控砂轮修整程序.最后通过磨削和检测实例,验证了理论的正确性和软件的可行性.