旋翼模型桨叶表面压力测量试验

采用"桨叶表面预先压槽,再粘贴片式压力传感器并粘胶带再开测量孔"的方法测量旋翼模型桨叶表面压力,在8 m x6 m风洞完成了地面悬停和风洞前飞试验,研究了桨叶表面压力测量技术和数据采集处理技术,获得了桨叶表面特征剖面的压力分布,建立了实用的旋翼模型桨叶表面压力测量试验技术.     

Millimeter Radar Instrumentation

Millimeter wavelength radars are used to study plasma effects associated with ionized flow fields of projectiles launched at hypersonic speeds into a free-flight ballistic range. Two CW Doppler radars, at frequencies of 35 and 70 Gc/s, measure the nose-on backscattering radar cross sections during flight. The design and performance of the two radars are described in detail. A signal simulator provides absolute calibration. The purpose is to measure changes that occur in the radar cross sections of hypersonic projectiles caused by highly ionized flow fields. Under certain conditions the nose-on backscattering radar cross section of a blunt-nosed metal projectile decreases drastically when a thin, shock-produced layer of ionized gas covers the projectile. A theoretical analysis of this effect is given. Comparisons between theoretical predictions and experimental data show good correlation.     

Preparation and Microstructure of Highly-Oriented LaNiO_3 Thin Films by RF Sputtering Method

In an attempt of being used as buffer layers and electrodes for the textured BaTiO3 (BTO) ferroelectric thin films, highly (100)-oriented LaNiO3 (LNO) thin films of different thicknesses were deposited directly on Si (100) substrate with radio-frequency (RF) magnetron sputtering method. It is observed that the substrate temperatures and the film thicknesses bring main influences on the micro-structures and orientation of the thin film. The effects of the thicknesses and substrate temperatures on the orientation of the films were studied on the LNO films of different thicknesses. The highly (100)-oriented LNO thin films were obtained at the substrate temperature of 600 ℃. The existence of epitaxially grown BTO films indicates that the oriented LNO thin films obtained in this work could be used as a buffer layer for epitaxial growth.     

Study on the Microstructure and Dielectric Properties of Barium Strontium Titanate Thin Films Prepared by Sol-gel Method

Sr0.5Ba0.5–xBixTiO3 (BST) thin films were fabricated on a Pt/SiO2/Si substrate by the sol-gel method. Then follows an investigation of the influences of bismuth (Bi) on the microstructures and the dielectric properties of Sr0.5Ba0.5-xBixTiO3 (BST) thin films. The micro-structures of the BST thin films were examined by the XRD and the TEM techniques. Tetragonal perovskite crystal grains were observed in BST thin films. Increasing Bi3 doping ration in BST will lead to decrease of the grain size. It is found that Bi3 doping decreases the dielectric loss and improves the frequency dispersion of the BST thin films. Not only is compressed the peak of temperature-dependence of dielectric constant of Bi3 -doped BST thin films but also moves into the low-temperature region. Moreover, the average Curie tem-perature decreases gradually with the Bi3 contents increasing.     

平板表面薄圆柱绕流摩擦力矢量场全局测量

针对壁面摩擦力矢量场测量问题,基于剪切敏感液晶(SSLC)涂层技术建立了一种测量平板表面摩擦力矢量场的方法。该方法基于多视角测量原理,采用六台同步相机从不同方向同时采集SSLC涂层在摩擦力作用下的颜色变化,与采用单台相机相比能够降低测量噪声,并且具有测量非定常流动的摩擦力场的潜力。应用该方法测量了平板表面薄圆柱绕流的摩擦力矢量场,结果表明:(1)SSLC涂层能够以彩色方式定性显示壁面摩擦力信息;(2)通过对不同方向观测的SSLC涂层颜色进行分析处理,该方法能够高分辨率测量薄圆柱绕流的摩擦力矢量场,详细地捕获了流动特征;(3)同一份SSLC涂层可以重复使用并且可用于测量不同的摩擦力矢量场。     

Moment-tensor inversion and decomposition for cracks in thin plates

The knowledge of crack type and dislocation orientation is helpful for the lifetime prediction of thin plates on aircrafts. The moment-tensor inversion utilizes the Acoustic Emission (AE) signals to detect cracks and the source mechanisms can be interpreted by the decomposition of moment tensors. Since the traditional moment-tensor inversion is implemented for the AE sources inside infinite elastic bodies, the inversion needs to be modified for the cracks in thin plates. In this study, the moment tensors of cracks in thin plates are derived and the inversion equation is provided based on the Green's function of second kind. A method of modifying the moment tensors to adapt to the existing decomposition processes and source-type plots is provided. By employing the Finite Element Method (FEM), the wave fields generated by the AE sources are computed. The AE sources continuously changing from pure tensile type (Model I) to shear type (Model II) are achieved in the FE models and the moment tensors are recovered. By the comparison between the reference values and recovered solutions, the source type can be accurately identified in the source-type plot and the applicability of the moment-tensor inversion for cracks in thin plates is confirmed.     

SiO_2溶胶在电沉积法制备CuInS_2薄膜中的作用

针对目前电沉积法制备的CuInS_2(CIS)薄膜存在S元素含量不足以及微观形貌差的问题,通过在普通镀液中加入SiO_2溶胶,采用一步电沉积技术在ITO导电玻璃上制备Cu-In-S预制薄膜,镀液的主要组成为金属盐、硫代硫酸钠和不同浓度SiO_2溶胶.在空气气氛中对Cu-In-S预制薄膜进行退火处理以获得多晶的CIS薄膜,并通过X射线衍射(XRD)、扫描电镜(SEM)、能量色散谱仪(EDS)及开路电位对CIS薄膜的结构、形貌、成分组成及光响应性能进行研究.结果表明:SiO_2溶胶浓度为4 mL/L时,得到的CIS薄膜的结晶度提高,同时,SiO_2溶胶作用下得到的CIS薄膜的表面形貌、成分组成和光响应性能都得到改善.因此,镀液中加入SiO_2溶胶有利于提高CIS薄膜的性能,尤其是浓度为4 mL/L时,性能提高得最为明显.     

光学滤光片薄膜边缘应力研究

以光学滤光片薄膜边缘应力作为对象,研究了Ge/Zn S单、多层光学薄膜应力的变化规律。通过实验研究了离子束轰击能量以及真空退火温度等因素对Ge/Zn S光学薄膜应力类型、大小、变化及其分布的影响规律。Zn S薄膜的应力为压应力,采用离子束辅助工艺后薄膜边缘应力变得均匀;真空退火使Zn S薄膜的应力减小为原来的一半。通过优化沉积参数和张应力、压应力薄膜的组合降低了Ge/Zn S多层光学薄膜的应力,结果表明其平均应力分别为0.1 MPa,而且处于压应力状态。     

薄片状聚酰亚胺多孔材料的研究进展

综述了薄片状聚酰亚胺多孔材料的研究进展,主要介绍了薄片状的聚酰亚胺多孔材料的产品种类、研究单位、性能指标、应用情况及制备方法,并提出了目前对薄片状聚酰亚胺多孔材料研究存在的问题以及研究现状,展望了薄片状聚酰亚胺多孔材料在今后的研究方向和发展趋势.薄片状聚酰亚胺多孔材料,已经作为垫片用在宇宙飞船的多层隔热系统中,甚至会逐渐替代传统的多层隔热系统材料.     

Residual stress determination in friction stir butt welded joints using a digital image correlation-aided slitting technique

This paper presents an incremental cutting method for evaluating the longitudinal residual stresses in a butt welded thin plate via combining the traditional residual stress measurement methods and the advanced optical technique.The proposed approach,which can be called digital image correlation (DIC)-aided slitting technique,introduces a successive extension slot to a speci men and employs the DIC technique to measure the released displacement profiles of the cutting sections after each cutting increment.Then the displacement profiles are used to directly calculate the residual stress distributions up to the slot tip and hence,a stress distribution can be obtained after a cutting increment.Finally,all of the stress distributions are averaged to ultimately determine the original residual stress field.This method does not include any complex experimental operations or tedious derivation,and the resolution of stress variation is greatly improved by the continuous measurement of the released displacements.The presented method has been preliminarily verified by a specimen with residual stress introduced by a four-point bending test.The results show that residual stresses determined by the DIC-aided slitting technique agree well with those from finite element (FE) prediction.The residual stress in a friction stir welded aluminum specimen obtained by the presented technique is also consistent with the evaluations given by X-ray diffraction.Fur thermore,the residual stresses obtained by the DIC-aided slitting technique demonstrate higher accuracy and stability than the evaluations derived by the DIC-aided contour method.     

Effects of Atomic Oxygen Irradiation on Transparent Conductive Oxide Thin Films

作为一种功能薄膜,透明导电氧化物(TCO)薄膜在飞行器的抗原子氧(AO)涂层和太阳能电池领域有着巨大的应用价值。ZnO:Al(ZAO)和In2O3:Sn(ITO)薄膜是目前研究和应用最广泛的TCO。本文对ITO薄膜和ZAO薄膜进行了不同通量的AO辐照。通过对辐照前后样品的X射线衍射、扫描电镜及霍耳效应的表征及测试,研究了AO辐照对这两种TCO薄膜的结构、性能及电学特性的影响。研究表明AO辐照对ZAO薄膜表面有明显的侵蚀作用,但对其结构和导电性能没有明显影响。对于ITO薄膜,随着AO通量的增大,其载流子浓度逐渐下降从而导致了电阻率的提高,电阻率的最大变化达到了21.7%。     

纳米薄膜脉冲激光沉积技术

简要介绍了脉丫激光薄膜沉积（PLD）技术的物理原理、独具的特点，介绍了在PLD基础上结合分子束外延（MBE）特点发展起来的激光分子束外延（L－MBE），以及采用L－MBE技术制备硅基纳米PtSi薄膜的结果。     

薄膜太阳能电池光电转换材料研究进展

在对太阳能电池基本原理进行介绍的基础上,综述了近年来光电转换材料的发展情况,重点对各种材料的优缺点、制备方法以及未来的发展趋势进行探讨。     

SiO2溶胶在电沉积法制备CuInS2薄膜中的作用

 针对目前电沉积法制备的CuInS2(CIS)薄膜存在S元素含量不足以及微观形貌差的问题,通过在普通镀液中加入SiO2溶胶,采用一步电沉积技术在ITO导电玻璃上制备Cu In S预制薄膜,镀液的主要组成为金属盐、硫代硫酸钠和不同浓度SiO2溶胶。在空气气氛中对Cu In S预制薄膜进行退火处理以获得多晶的CIS薄膜,并通过X射线衍射（XRD）、扫描电镜（SEM）、能量色散谱仪（EDS）及开路电位对CIS薄膜的结构、形貌、成分组成及光响应性能进行研究。结果表明：SiO2溶胶浓度为4 mL/L时,得到的CIS薄膜的结晶度提高,同时,SiO2溶胶作用下得到的CIS薄膜的表面形貌、成分组成和光响应性能都得到改善。因此,镀液中加入SiO2溶胶有利于提高CIS薄膜的性能,尤其是浓度为4 mL/L时,性能提高得最为明显。     

多弧离子镀Cr/Cr2O3薄膜红外及可见光谱特性

采用多弧离子镀制备了具有不同色彩的Cr/Cr2O3薄膜,利用紫外-可见光分光光度计研究了薄膜在可见和红外波段的光谱特性,利用SEM进行薄膜表面结构和形貌的分析,利用四探针测阻仪测试了样品的方块电阻,利用红外发射率测量仪测试了样品的红外发射率。结果表明:Cr/Cr2O3薄膜具有丰富的色彩,在可见光区有明显的反射峰,可见光区光谱特性主要受膜厚的影响,方块电阻随膜厚增加而有变大,样品的红外发射率主要取决于金属层,平均红外发射率最小降至0.371。     

连续离子层吸附反应法制备超薄功能膜及应用

阐述了液相法中制备超薄功能膜的新方法——连续离子层吸附反应法(Successive Ionic Layer Adsorption and Reaction,SILAR)。探究了它的薄膜生长机理、工艺参数影响以及应用现状,指出了尚需深入研究的问题。     

某带分流叶片的亚声速离心压气机叶轮CFD结果确认及分析

为了研究数值模拟结果的准确性,使用计算流体动力学(CFD)软件Numeca,采用Spalart-Allmaras(S-A)模型和shear stress transport(SST)模型对某压比为1.5的亚声速离心压气机叶轮的性能进行了计算,并将4个不同截面上的速度分布等计算结果和实验数据进行了对比.结果表明:S-A模型和SST模型的计算结果几乎完全相同,误差小于1%;整体性能的模拟计算结果和实验值吻合较好,在设计工况点,误差在2%以内,在非设计工况点,误差也小于6%;不同截面上速度分布的计算结果和实验值相差较大,在轮毂附近,最大误差在20%左右,在轮缘附近,部分截面最大误差高于100%,不能真实反映轮缘附近的流动情况.      

[001]取向DD6单晶合金的薄壁试样持久性能与断裂行为

采用薄壁试样研究了温度为980℃、应力为250MPa条件下［001］取向DD6单晶合金的薄壁持久失效行为,结果表明:薄壁试样的持久寿命低于标准圆棒试样,表现出显著的薄壁效应。薄壁试样的厚度和持久寿命之间存在函数关系。薄壁试样持久断口边缘区域氧化严重,内部区域为微孔聚集型断裂,持久断裂模式为“表面氧化-裂纹萌生-扩展”和“内部蠕变损伤”共同作用,且试样越薄,表面氧化程度越大,持久寿命越短。      

不同进口截面下液力透平非定常压力脉动计算

为了研究不同进口截面对液力透平内压力脉动的影响,利用CFX软件对一单级液力透平进行非定常数值计算,通过设置监测点,计算各监测点在不同进口截面下的压力脉动,通过快速傅里叶变换将其压力脉动计算结果做相应分析,分析各监测点处压力脉动的时域和频域分布.结果表明:蜗壳内在大蜗壳进口下,随着蜗壳进口直径的增加,每个监测点处的压力逐渐增加,而在小蜗壳进口下,每个监测点处的压力逐渐减小.在距离蜗壳收缩管较远处,大蜗壳进口下的压力脉动较小,而在距离收缩管较近处,小蜗壳进口下的压力脉动较小.在叶轮内不同进口截面压力脉动的差异在同一时刻从进口到出口逐渐减小.尾水管内在小蜗壳进口下尾水管进口处的压力脉动最大.      

Aerodynamic Characteristics of Thin Cylindrical and Conical Shells in the Incompressible Flow

The paper presents aerodynamic characteristics of thin cylindrical and conical shells in the incompressible flow. Experimental data and results of numerical simulation in the OpenFoam software are compared. It is shown that the aerodynamic characteristics of the thin shells differ from the aerodynamic characteristics of the corresponding solid bodies and depend on the shell geometry parameters.