H_∞滤波算法及其在GPS/SINS组合导航系统中的应用

 在对 H∞ 估计问题进行数学描述的基础上,建立了一种 H∞ 次优滤波算法的迭代方程。定性讨论了H∞滤波算法与传统 Kalman滤波器的关系,通过在 GPS/SINS组合系统中的实际应用进一步从精度、鲁棒性等性能指标方面对 H∞ 滤波和 Kalman滤波算法进行了比较。仿真结果表明,在理想条件下,Kalman滤波方法具有较高的精度;但是,当系统模型和外部干扰统计特性发生变化时,H∞ 滤波算法明显具有良好的鲁棒性能,同时,估计精度也较高,有效地克服了 Kalman滤波器存在的局限性。     

Effects of the Fabrication Processes of NC-Si:H Films on Their Mechanical Properties

Studies of nanoindentation were performed on nc-Si:H films to evaluate the effects of the fabrication processes on their mechani-cal properties. It is observed that with the decrease of the SiH4 contents, the grain size of the films increases gradually, and as does the crystalline volume fraction. The smaller the grains become, the more homogeneous the films, and the more even the hardness as well as the modulus will be. The hardness and the modulus will increase with the substrate’s temperature rising. The hardness and the modulus of the nc-Si:H films on the Si substrate prove to be higher than those on the glass substrate given the same technology parameters. How-ever, the films on the glass substrate appear to be more homogeneous.     

Temperature Fluctuations,H II Region Abundances,and Primordial Helium

There is evidence for temperature fluctuations in Planetary Nebulae and in some Galactic H II regions. If such fluctuations occur in the low metallicity, extragalactic H II regions used to probe the primordial helium abundance, the derived 4He mass fraction, YP, could be systematically different from the true primordial value. Although this effect could be large, there are no data which allow us to estimate the size of the temperature fluctuations for the extragalactic H II regions. Therefore, we have explored this effect via Monte Carlo simulations of the data in which the abundances derived from a fiducial data set are modified by T chosen from a distribution with 0 T Tmax where Tmax is varied from 500 K to 4000 K.     

一类有理参数三次曲线的形状分析(英文)

一条有理参数三次 H-样条曲线是由一组控制顶点和两顶点连线上的百分比参数所确定。移动一个顶点仅影响三段曲线。有理 H-样条具有许多类似于 B-样条曲线的性质 ,也有 B-样条不具有的性质。本文是在文 [1 ]基础上的继续和发展 ,主要对有理 H-样条曲线的形状进行分析 ,讨论其诸如拐点和奇点的几何特征 ,给出有理参数平面三次 H-样条曲线在非退化情况下有拐点的充要条件 ,并证明在区间 ( 0 ,1 )内曲线段无奇点的结论。为了便于对参数曲线段的形状控制和几何特征的进一步认识 ,在许多的实际应用中 ,需要分析参数曲线段上有无多余拐点和奇点 ,如果有就要消除它。故本文的研究结果无论对理论或实际应用都非常重要。     

弹性体运载火箭建模及控制器设计

考虑运载火箭飞行过程中的弹性振动特性,对运载火箭进行全量动力学建模以及控制器设计。首先将运载火箭考虑为一维梁模型并建立全量动力学模型,分别引入自适应滤波姿态控制算法和H_2范数鲁棒增益调度控制算法设计控制器。仿真结果表明:在考虑舵机非线性情况下两种控制方法均能够满足精度要求,在具有较大外部扰动情况下,鲁棒增益调度控制算法相较于自适应滤波算法具有较强的鲁棒性。     

基于T-S模糊模型的模糊大系统的混合滤波

针对非线性大系统内部过程参数的检测估计,采用连续模糊大系统模型,利用lyapunov定理和分布式处理方法,给出了模糊大系统的H2/H∞混合滤波器设计方法。该方法在保证滤波误差系统全局稳定的同时,具备了H2/H∞性能。通过求解线性矩阵不等式,可以得到滤波器参数。最后,用一个数值例子验证了该方法的正确性和有效性。     

基于H∞方法的控制系统作动器最优控制仿真研究

在设计控制系统模型时,首先引入了有限差分法(FDM)离散化后的波动方程,然后基于H∞最优控制原理,检查闭环控制系统的稳定性和可探测性,对控制系统传感器和作动器的位置进行优化配置.通过计算闭环反馈系统的范数,最终得到了控制系统的最优控制算法.仿真结果表明,利用波动方程来优化控制系统传感器和作动器位置的算法是可行的,可广泛应用于飞控系统的设计中.     

Cross-sectional deformation behavior of double-ridged rectangular tube with fillers in different stages of H-typed bending

The bent double-ridged rectangular tube (DRRT) with high forming quality is helpful to improve the microwave transmission accuracy. For reducing the cross-sectional deformation in the H-typed bending process, in addition to using rigid mandrel to support the inside of tube, ridge groove fillers are also added to restrict the deformation of ridge grooves. Because of the change of stress and strain state of bent tube in bending, rigid mandrel retracting and specially twice-springback stages, and the springback of fillers, the cross-sectional deformation of tube in each stage may be different. Therefore, based on the ABAQUS platform, the finite element models (FEM) for H-typed bending, mandrel retracting and twice-springback stages of H96 DRRT with fillers were established and validated. It is found that, for the height and width deformation of tube and spacing deformation of ridge grooves, retraction of mandrel can make the distribution of these deformations more uniform along the bending direction. The first springback can reduce these deformations significantly, which should be emphasized. But the second springback only increases them by less amount, which can be ignored. The smaller height deformation of ridge groove and filler can be neglected.     

基于传热反问题方法的N_2O/C_2H_4预混推进剂燃烧室热流测量研究

测量液体火箭发动机的热载荷是获取燃烧室内部信息的重要方法。为了获取N_2O/C_2H_4预混推进剂燃烧室内壁的热载荷,建立了液体火箭发动机的热流计算的反问题方法,该方法基于对燃烧室壁面温度场的直接求解,通过对轴向多个位置测量温度的反演计算得到燃烧室内壁热流和温度。研究表明:应用文中建立的传热反问题方法能够较为准确地获得热流随时间及空间的分布;热电偶的位置对计算准确性有明显的影响,与理论深度偏差在0.2mm以内的随机深度偏差可导致超过4%热流反演误差;N_2O/C_2H_4预混推进剂燃烧室热流及温度沿轴向逐渐降低,表明燃烧室内的反应释热过程主要在燃烧室头部附近发生。     

模具约束条件对H96黄铜双脊矩形管E弯截面变形的影响

 双脊矩形管的绕弯成形受内外侧模具的共同约束,不同模具约束下管坯的受力不同,使得其截面变形情况也不相同,而截面变形严重地影响弯管件的成形质量和使用性能。因此,基于ABAQUS有限元平台建立了双脊矩形管E弯成形三维有限元模型,并通过实验验证了模型的可靠性。采用所建模型,研究了内外侧模具约束条件对双脊矩形管E弯截面变形的影响规律,发现当只有内腹板脊槽受约束时,内腹板脊槽的内缩变形可得到较好的控制,而其他部位的变形则有增大的趋势;当只有外腹板脊槽受约束时,内腹板脊槽宽度变形基本不发生变化,而其他部位的变形则有减小的趋势;当内外腹板脊槽均受约束时,可较好地控制双脊矩形管E弯过程中的截面变形。芯头个数对整管截面高度、宽度、外腹板脊槽宽度与两脊槽底部的间距的变形影响较大,但对内腹板脊槽宽度的变形影响不显著。