模具约束条件对H96黄铜双脊矩形管E弯截面变形的影响

 双脊矩形管的绕弯成形受内外侧模具的共同约束,不同模具约束下管坯的受力不同,使得其截面变形情况也不相同,而截面变形严重地影响弯管件的成形质量和使用性能。因此,基于ABAQUS有限元平台建立了双脊矩形管E弯成形三维有限元模型,并通过实验验证了模型的可靠性。采用所建模型,研究了内外侧模具约束条件对双脊矩形管E弯截面变形的影响规律,发现当只有内腹板脊槽受约束时,内腹板脊槽的内缩变形可得到较好的控制,而其他部位的变形则有增大的趋势;当只有外腹板脊槽受约束时,内腹板脊槽宽度变形基本不发生变化,而其他部位的变形则有减小的趋势;当内外腹板脊槽均受约束时,可较好地控制双脊矩形管E弯过程中的截面变形。芯头个数对整管截面高度、宽度、外腹板脊槽宽度与两脊槽底部的间距的变形影响较大,但对内腹板脊槽宽度的变形影响不显著。     

Cross-sectional deformation of H96 brass double-ridged rectangular tube in rotary draw bending process with different yield criteria

Different yield criterion has great difference in predicting the deformation of tube with different material. In order to improve the prediction accuracy of the cross-sectional deformation of the double-ridged rectangular tube (DRRT) during rotary draw bending (RDB) process, Mises isotropic yield criterion, Hill’48 and Barlat/Lian anisotropic yield criteria commonly used in practical engineering are introduced to simulate RDB of DRRT. The inverse method combining uniaxial tensile test of whole tube and response surface methodology was proposed to identify the parameters of Hill’48 and Barlat/Lian yield criteria of small-sized H96 brass extrusion DRRT as well. Then based on ABAQUS/Explicit platform, the FE models of RDB process of DRRT considering Mises, Hill’48 and Barlat/Lian yield criteria were built. The results show that: The variation trend of cross-sectional deformation ratio is same when using different yield criteria. The cross-sectional deformation ratio by using Mises yield criterion is close to that by using Hill’48 yield criterion. However, there is a quite difference between by using Barlat/Lian yield criterion and by using Mises or Hill’48 yield criteria. The prediction values of cross-sectional height deformation by using three yield criteria all underestimate the experiment ones, and the prediction values of cross-sectional width deformation overestimate the experiment ones. By comparing the simulation results of cross-sectional deformation of the DRRT with different yield criteria and experiment ones, Barlat/Lian yield criterion is found to be suitable for describing the RDB process of DRRT.     

‘Size effect’ related bending formability of thin-walled aluminum alloy tube

Aluminum alloy (Al-alloy) thin-walled (D/t > 20, diameter D, wall thickness t) bent tubes have attracted increasing applications in many industries with mass quantities and diverse specifications due to satisfying high strength to weigh ratio requirements of product manufacturing. However, due to nonlinear nature of bending with coupling effects of multiple factors, the similarity theory seems not applicable and there occurs a challenge for efficient and reliable evaluation of the bending formability of thin-walled tube with various bending specifications. Considering the unequal deformation and three major instabilities, the bending formability of thin-walled Al-alloy tube in changing tube sizes such as D and t are clarified via both the analytical and FE modeling/ simulations. The experiments of rotary draw bending are conducted to validate the theoretical models and further confirm ’size effect’ related bending formability. The major results show that (1) The anti-wrinkling capability of tube decreases with the larger D and smaller t, and the effect significance of t is larger than that of D even under rigid supports; (2) The wall thinning increases with the larger D and smaller t, and this tendency becomes much more obvious under rigid supports; (3) The cross-section deformation increases with the larger D and smaller t according to the analytical model obtained intrinsic relationship, while this tendency becomes opposite due to the nonlinear role of mandrel die; (4) The size factor D/t can be used as a nondimensional index to evaluate both the bending formability regarding the wall thinning and cross-section deformation.     

动压气浮球轴承承载力分析

 本文采用曲面间的保角变换,将球面润滑问题变换为平面润滑问题,导出等角螺线槽球形轴承的承载能力和气膜刚度的近似解析表达式和最佳槽型参数。本文结果适用于小压缩数和小偏心的情况。     

弯管成形理论和技术研究进展与发展趋势(英文)

As one kind of key components with enormous quantities and diversities,the bent tube parts satisfy the increasing needs for lightweight and high-strength product from both materials and structure aspec...     

A Study on Multi-defect Constrained Bendability of Thin-walled Tube NC Bending Under Different Clearance

Thin-walled tube numerical control (NC) bending is a tri-nonlinear physical process with multi-defect and multi-die constraints. The clearance on each contact interface is the major factor to indicate the contact conditions. A three-dimensional-finite element (3D-FE) model is established to consider the realistic dynamic boundary conditions of multiple dies under ABAQUS/Explicit platform. Combined with experiment, numerical study on bending behavior and bendability under different clearance between tube and various dies is conducted in terms of wrinkling, wall thinning and cross section deformation. The results show that (1)with smaller clearance of tube-wiper die and tube-mandrel, the wrinkling can be restrained while the wall thinning It and cross-section deformation Id increase; while excessive small clearance blocks tube materials to flow past tangent point and causes piles up, the onset of wrinkling enhances It and Id. (2)Both It and Id decrease with smaller clearance of tube-pressure die; the wrinkling possibility rises with larger clearance on this interface if the mandrel’s freedom along Y-axis is opened; smaller clearance of tube-bend die prevents wrinkling while increases It, and the clearance on this interface has little effect on Id. (3)A modified Yoshida buckling test (YBT) is used to address the wrinkling mechanisms under normal constraints in tube bending: the smaller clearance may restrain wrinkling efficiently; the smaller wall thickness, the less critical clearance needed; the critical clearance for tube bending 38 mm×1 mm×57 mm (tube outer diameter×wall thickness×centerline bending radius) equals about 20% of initial wall thickness.     

Deformation Behavior of Medium-strength TA18 High-pressure Tubes During NC Bending with Different Bending Radii

To improve the forming quality and forming limit of the numerical control (NC) bending of high-pressure titanium alloy tubes, in this study, using three-dimensional (3D) finite element method, deformation behavior of medium-strength TA18 high-pressure tubes during NC bending with different bending radii is investigated. The results show that the cross-sectional deformation and the wall thickness variation during NC bending of TA18 tubes using a small bending radius (less than 2 times of tube outside diameter) are clearly different from that using a normal bending radius (between 2 and 4 times of tube outside diameter). For bending with a normal bending radius, with or without a mandrel, the distribution of the flattening in the bending area resembles a platform and an asymmetric parabola, respectively. For bending with a small bending radius, with or without a mandrel, the flattening both distributes like a parabola, but the former has a stable peak which deflects toward the initial bending section, and the latter has a more pronounced peak with a bending angle and deflects slightly toward the bending section. The wall thickness variations with a normal bending radius, with and without a mandrel, both resemble a platform when the bending angle exceeds a certain angle. For the bending with a small radius, the distribution of the wall thickness variation without a mandrel follows an approximate parabola which increases in value as the bending angle increases. If a mandrel is used, the thickening ratio increases from the initial bending section to the bending section.     

空心涡轮叶片复杂陶芯弯扭变形分析方法比较

陶芯作为熔模铸造空心涡轮叶片的内腔转接件,其弯扭变形程度直接关系到空心涡轮叶片的壁厚尺寸精度。为了研究陶芯制造过程中出现的弯曲和扭曲变形,首先,借鉴叶片给出了陶芯弯曲变形和扭曲变形的定义,并根据陶芯结构特点研究了陶芯弯扭变形的计算方法,包括基于轮廓线的弯扭变形计算方法:主动轮廓模型法和样条拟合轮廓线法,与基于数据点的弯扭变形计算方法:凸包算法、二维配准算法和距离权值算法。然后,分别通过仿真与实测数据比较了5种算法,结果表明:样条拟合轮廓线法具有更高的稳定性和精度。     

薄壁管数控弯曲过程中失稳起皱的主要影响因素

 针对薄壁管数控弯曲精确成形过程在多因素交互作用下可能发生失稳起皱这一复杂物理问题, 基于起皱能量准则和有限元方法相结合, 提出了预测该过程起皱发生的能量( 数值) 方法, 研究了影响薄壁管数控弯曲成形过程起皱发生的主要因素及影响机制。结果表明, 弯曲半径、相对管径、芯棒伸长量和摩擦因素是影响薄壁管数控弯曲精确成形过程起皱发生的主要因素, 而材料的应力强度系数和加工速度等对起皱发生影响较小。研究结果为薄壁管数控弯曲精确成形过程参数的确定和优化创造了条件。     

一种基于有限元法和弹性接触理论的齿轮啮合刚度改进算法

提出了一种将有限元法和弹性接触理论相结合的齿轮啮合刚度计算方法.该方法利用子结构法提取齿面原始柔度矩阵并分离出接触点弯曲变形,根据线弹接触变形解析公式计算接触变形,通过求解非线性变形协调方程得到齿轮时变啮合刚度和齿面载荷分布.以一对齿轮副为例,计算的啮合刚度与航空标准计算结果相差在6%以内.该方法发挥了有限元法在预测物体整体变形方面的优势,同时结合弹性接触理论能够准确计算局部接触变形的优点,与常规有限元法相比,能够有效地提升计算效率.由于接触变形问题的非线性,啮合刚度随总啮合力增加呈现非线性增大的趋势.      

Plastic deformation analysis and forming quality prediction of tube NC bending

Plane strain assumption and exponent hardening law are used to investigate the plastic deformation in tube bending. Some theoretical formulae including stress, curvature radius of neu-tral layer, angle of neutral layer deviation, bending moment, wall thickness variation and cross-section distortion, are developed to explain the phenomena in tube bending and their magnitudes are also determined. During unloading process, the springback angle is deduced using the virtual work principle, and springback radius is also given according to the length of the neutral layer which remains unchanged before and after springback. The theoretical formulae are validated by the experimental results or the validated simulation results in literature, which can be used to quickly predict the forming quality of tube numerical control (NC) bending.     

铝合金型材柔性垫弯曲成形实验研究

进行两种典型铝合金型材的弯曲实验,研究主要工艺参数对弯曲过程的影响.结果表明,型材的截面形状、相对厚度及抗弯截面系数等是决定弯曲性能的主要因素.压辊的压入深度、柔性垫的性能以及型材的约束方式等是影响弯曲半径、截面变化的关键.对实验中主要缺陷和质量问题的产生及其控制进行分析和讨论.     

低速轴流压气机周向单槽机匣处理扩稳实验研究

周向槽机匣处理作为一种有效的扩稳措施得到了广泛应用,但是缺乏对其机理的深入理解和认识。为此,在一台低速单转子轴流压气机上考察了周向单槽机匣处理随轴向位置变化的扩稳效果。实验中获得了单槽不同轴向位置的扩稳规律,在该台压气机上得出了扩稳效果最好的槽位于40%~60%轴向弦长,而当单槽位于27%轴向弦长附近时,其扩稳效果最差。在此基础上,选取了最优扩稳槽位和最差扩稳槽位进行详细的壁面非定常流场测量和尾迹测量,对比分析了光壁条件与各单槽处理机匣对叶顶间隙泄漏流和转子尾迹的影响。结果表明,采用扩稳效果最优槽位之后,周向单槽能推迟叶顶间隙泄漏流与主流交界面前移,以及减弱叶顶间隙泄漏流非定常性,且能明显增强尾迹区1BPF(叶片通过频率)的能量,同时减弱0.5BPF的能量,达到扩稳的目的。而对于扩稳效果最差槽位而言,叶顶间隙泄漏流与主流交界面直到失速前也无法跨过单槽从叶片前缘溢出,周向单槽改变了叶顶间隙内部诱发突尖失速先兆的扰动传播方式;另外,其对转子尾迹区0.5BPF和1BPF的影响也比较小,从而使得其扩稳效果减弱。     

Impact of bending dies with different friction forms on forming force and quality of tubes manufactured by free bending technology

In the 3D free bending forming system, the bending die can be designed either in a sliding type or rolling friction type. Bending die-based sliding friction type is often called normal bending dies; however, the bending dies-based rolling friction type includes bending die-based roller type and ball type in structure. In the current study, the impact of three bending dies on the forming force, and the bent tube quality was investigated. The obtained results showed that the tangential stresses and strains of the tubes formed by the bending die-based roller type were the smallest among the three bending dies. Besides, the spherical bearing force P_U was reduced drastically after using the roller type and ball type compared to the sliding friction type. Moreover, the uniformity of the wall thickness distribution of the tubes formed by the roller type and ball type was better than those obtained from the sliding friction type. In addition, the cross-section distortion rate was reduced by 2.8% using the roller type, and 1.8% using ball-type compared to the sliding friction type.     

凹槽对涡轮叶片前缘换热特性影响的实验研究

为了探究带有凹槽造型的涡轮叶片前缘结构的换热特性,采用瞬态热色液晶技术研究了凹槽对涡轮叶片前缘外表面换热系数的影响,获得了不同主流雷诺数以及湍流度下涡轮叶片原始前缘结构及带两种不同深度凹槽的前缘结构外表面的换热系数分布数据,并采用努塞尔数评估对比了三种结构下的换热特性。实验结果表明：原始前缘结构存在高换热系数区,随着湍流度的增大,高换热核心区显著增大；由于凹槽对滞止区域的流动产生了影响,带凹槽的前缘结构在不同工况下均表现出将原始结构高换热核心区分割为凹槽两侧突出边缘的高换热区和槽内低换热区的分布特征；凹槽可以显著降低前缘表面的换热强度,带浅凹槽的前缘结构在前缘表面的面平均努塞尔数相比原始前缘结构降低约7.9%~14.5%,带深凹槽的前缘结构相比原始前缘结构降低约9.1%~20.9%；与Reg=200,000相比,当Reg=150,000时,带凹槽的前缘结构相比原始结构的低换热优势更强。     

引入材料参数的弯管中性层偏移解析模型

中性层偏移是表征管材弯曲内外侧不均匀变形程度的关键参数。基于弯管截面力矩平衡条件,建立了引入材料参数的管材弯曲变形中性层偏移解析模型,针对管材数控绕弯和压弯过程对所建模型从多个方面进行了评估,研究了不同几何和材料等管材本征参数下的管材弯曲中性层偏移规律。结果表明:应用于TA18钛管数控绕弯,发现所建解析模型与已有解析方法预测精度相当,但能考虑材料参数影响,且相较于有限元模拟,本文解析模型更接近实验结果;应用于A6063铝合金管和AZ31镁合金管压弯过程,并与Hasegawa解析方法相较,发现本文解析模型能够准确预测拉压不对称对压弯中性层偏移的影响;弯曲半径减小,弯管直径增大,中性层向弯曲内侧移动;拉压屈服强度比减小,厚向异性指数增大,中性层向弯曲内侧移动。     

Structurally coupled characteristics of rotor blade using new rigid-flexible dynamic model based on geometrically exact formulation

In rotor dynamics, blades are normally modelled as a slender beam, in which elastic deformations are coupled with each other. To identify these coupling effects, new rigid-flexible structural model for helicopter rotor system is proposed in this paper. Finite rotations of the whole blade(on flapwise, lagwise, and torsional) are described as three global rigid degrees of freedom.The nonlinear deformation geometrics of the beam is built on geometrically exact beam theory.New expressions for blade ...     

纤维缠绕角度对CFRP-Al混合圆管横向受载性能影响

基于准静态横向弯曲试验对缠绕工艺下制备的CFRP/Al混合圆管进行抗弯性能和吸能特性研究,分析了混合圆管的破坏模式,基于不同纤维缠绕角度的碳纤维复合材料-铝合金混合圆管三点弯曲试验结果,通过有限元仿真方法研究了内层纤维缠绕角度对其横向抗弯与吸能特性的影响。试验结果表明,CFRP-Al混合圆管横向载荷下的失效形式、损伤模式与纯铝管基本保持一致,但受纤维缠绕角度的影响失效形貌略有差异。纤维缠绕角度越小,CFRP-Al混合圆管的抗弯性能和吸能性越好,同时压溃效率(CFE)明显降低。基于验证的有限元模型,研究不同角度纤维缠绕内层对于表层纤维层的应力传递影响,小角度缠绕内层对于管件的轴向拉伸变形抑制增加了管件整体峰值载荷与吸能作用,大角度缠绕内层对于管件环向刚度的提升增加了整体压溃效率。依此分析可为合理设计CFRP-Al混合管提供有效依据。     

大型客机柔性后缘增升装置气动机构一体化优化设计

增升装置的设计对于大型客机来说是十分重要的,柔性可变弯的增升装置是未来大型客机的发展趋势,也是当前的研究热点。以某大型宽体客机内段翼型为研究对象,在襟翼内部的柔性变弯机构的带动下,可以使襟翼的后50%部分实现柔性变弯。在原始刚性襟翼的基础上,柔性变弯后的襟翼可使襟翼后缘增加8°的偏角。之后在三维后缘铰链襟翼机构的带动下,同时襟翼内部使用柔性变弯机构,采用"前缘下垂+后缘襟翼柔性变弯+后缘简单铰链襟翼联合扰流板下偏",进行起飞和着陆构型的二维气动/机构一体化优化设计,优化出来的结果与原始不柔性变弯的翼型相比,起飞构型的最大升力系数的增加量为0.119,着陆构型的最大升力系数的增加量为0.162,且着陆最优构型推迟1°迎角失速。