双流制窄轨电力机车用异步牵引电机设计

将牵引电机应用于双流制窄轨电力机车时,由于窄轨机车轨距小,所以牵引电机安装空间异常狭小,比一般牵引电机在安装空间、电机结构、电磁负荷等方面的要求更加苛刻。针对窄轨双流制电力机车的运用特点和特殊要求进行了分析,提出了牵引电机的设计要求和关键技术难点,并对关键技术难点给出了相应的分析和解决措施。对该牵引电机的制造过程及电机试验测试情况进行了论述。试验结果表明,该牵引电机达到了设计预期,完全能满足设计要求。     

基于6SPS并联机构标定新方法

系统研究6SPS并联机构标定的方法。研究中应用激光跟踪仪测量、基于并联机构正解和定位误差旋量的计算,正交试验进行试验设计,应用非线性最小二乘参数辨识。仿真验证辨识的几何误差可以等于假定值,试验验证位姿精度提高了10倍。     

ZYTC600专用镗床精密转台微调机构设计与分析

为解决框架类零件的高位置度孔的精密镗削加工问题,研发了ZYTC600专用镗削机床.其精度指标优于现有的通用镗床(包括进口镗床),尺寸在500mm范围内,同轴度优于2μm,垂直度优于5μm,其中的关键部件双回转轴系分度精密转台采用了一套精密调整机构,可以实现0.2s”的精密调整,通过有限元分析得到其驱动刚度可达到800N/μm,可以满足加工需求.     

前向数据接入方式对导航星座网络通信性能的影响分析

对采用时分多址轮询建链体制的导航星座星间链路网络，为了指导星间链路网络地面前向数据接入的应用，分析了不同地面前向数据接入方式的星-星-地联合数据交互机制及其对网络通信性能的影响，并结合应用代价给出了综合评价和使用建议。以前向数据最快路径接入方式和固定节点接入方式为代表，分析了星间链路网络与地面间星 星 地联合数据交互机制的特点，明确了两种方式下星间链路网络拓扑路由规划策略的制定原则。通过构建Walker 24/3/1导航星座星间链路网络数据处理模型及典型星地运行场景，对两种地面前向数据接入方式仿真分析了星间链路通信容量和传输时延等网络通信性能，比较分析了通信容量及数据拥塞规律，得出前向数据最快路径接入方式相比于固定节点接入方式在通信性能上有较明显优势的结论。最后，综合给出了两种星 星 地联合数据交互机制的应用性评价,同时给出了在通信容量较低且通信时延要求不高、但可靠性要求较高的应用条件下，可适度采用固定节点接入方式的建议。     

一种卫星信道的反馈优化接入机制

提高卫星信道资源利用率，探索高效可行的端站接入机制是卫星通信发展亟待解决的问题之一。当前卫星通信DVB-RCS标准基于带宽预先规划的接入机制与端站随遇接入的需求矛盾凸显，因此提出一套信道反馈优化接入机制，综合考虑各端站数据业务需求，在不改变原有协议信令特征的基础上，探索性地引入谦虚度激励方法，创造性地构造动态协商反馈模型并加以求解，达到提高端站接入数量、满足随遇接入需求、提升信道利用效率、最大化整体带宽通信业务效益的目的。通过试验验证，带宽分配反馈优化机制比传统模式提高近1倍接入率，最大端站数接入时算法耗时约只有0.67s，可为卫星信道使用提供技术参考。     

Geometric error analysis of an over-constrained parallel tracking mechanism using the screw theory

This paper deals with geometric error modeling and sensitivity analysis of an overconstrained parallel tracking mechanism. The main contribution is the consideration of overconstrained features that are usually ignored in previous research. The reciprocal property between a motion and a force is applied to tackle this problem in the framework of the screw theory. First of all, a nominal kinematic model of the parallel tracking mechanism is formulated. On this basis, the actual twist of the moving platform is computed through the superposition of the joint twist and geometric errors. The actuation and constrained wrenches of each limb are applied to exclude the joint displacement. After eliminating repeated errors brought by the multiplication of wrenches, a geometric error model of the parallel tracking mechanism is built. Furthermore,two sensitivity indices are defined to select essential geometric errors for future kinematic calibration. Finally, the geometric error model with minimum geometric errors is verified by simulation with SolidWorks software. Two typical poses of the parallel tracking mechanism are selected, and the differences between simulation and calculation results are very small. The results confirm the correctness and accuracy of the geometric error modeling method for over-constrained parallel mechanisms.     

热处理对FeCo-2V-0.5Cr软磁合金力学与磁学性能的影响

针对FeCo-2V-0.5Cr软磁合金,研究了真空热处理时间对其微观组织结构、力学与磁学性能的影响规律,发现在800℃下热处理时间为2h左右时,合金的抗拉强度和延伸率达到最佳,同时仍保持良好的软磁性能,抗拉强度、延伸率以及矫顽力分别为867.8MPa、10.4%以及2.0Oe。进一步对该合金进行附加磁场下的真空热处理,重点研究了合金的交流损耗与矫顽力随附加磁场方式包括磁场撤除温度与磁场下保温时间的变化规律,发现适当的磁场热处理对合金相关力学性能影响不大,但由于合金中产生了单轴各向异性而使合金矫顽力进一步降至1.6Oe。     

An experimental system for release simulation of internal stores in a supersonic wind tunnel

Aerodynamic parameters obtained from separation experiments of internal stores in a wind tunnel are significant in aircraft designs. Accurate wind tunnel tests can help to improve the release stability of the stores and in-flight safety of the aircrafts in supersonic environments.A simulative system for free drop experiments of internal stores based on a practical project is provided in this paper. The system contains a store release mechanism, a control system and an attitude measurement system. The release mechanism adopts a six-bar linkage driven by a cylinder, which ensures the release stability. The structure and initial aerodynamic parameters of the stores are also designed and adjusted. A high speed vision measurement system for high speed rolling targets is utilized to measure the pose parameters of the internal store models and an optimizing method for the coordinates of markers is presented based on a priori model. The experimental results show excellent repeatability of the system, and indicate that the position measurement precision is less than0.13 mm, and the attitude measurement precision for pitch and yaw angles is less than 0.126°, satisfying the requirements of practical wind tunnel tests. A separation experiment for the internal stores is also conducted in the FL-3 wind tunnel of China Aerodynamics Research Institute.     

HED-21S数控综合实验台画笔自动控制机构设计

以数控系统的PLC控制为基础,设计HED-21S机械笔控制系统结构,它可控制电磁铁的动作,执行画笔的上下运动。这支笔在X、Z型十字窗格可以绘制任意几何形状,该设计符合要求的快速定位数控直线移动,及圆弧插补功能,有助于提高数控编程效率和数控教学质量。     

空间光学相机调焦技术研究

调焦技术是空间光学相机研制的关键技术之一,对于保证相机成像质量具有重要作用.文章阐述了造成相机离焦的主要因素,在调研分析国内外空间光学相机调焦方式的基础上,对相机调焦方式的选用原则进行了归纳,并介绍了常用调焦机构的基本结构形式和优缺点,以及具有发展前景的调焦光学元件,可为相机调焦技术的研究提供借鉴和帮助.