基于一类含极少运动副四支链两转一移三自由度并联机构的五轴混联机器人

首先提出了一类含较少运动副四支链两转一移三自由度（2R1T）并联机构（PMs）2RPU-UPR-RPR和2UPR-RPU-RPR，然后提出了极限约束力螺旋系的概念，分析四支链2R1T并联机构末端的极限约束力螺旋系，对所提出的四支链2R1T并联机构是否同类机构中含运动副最少进行了论证。基于提出的四支链并联机构构造了一种五自由度混联机器人机构，建立了2-RPU-UPR-RPR并联机构的位置反解模型，并将其等效成一个三自由度串联机构RPR，进而对整个混联机器人机构进行了位置正反解分析，建立得到了混联机器人机构位置反解的显式解析表达式，并用加工球面轨迹的算例对所建运动学模型的正确性进行验证。提出的五自由度混联机器人含有极少的运动副，且所有转动自由度均具有连续转轴，能够得到解析的位置模型表达式，很容易实现轨迹规划与运动控制，具有良好的应用前景。     

改进Delta并联机构运动可靠性分析

 运动精度是评价机构质量的重要考核指标。以往并联机构运动精度分析中,往往不考虑输入误差的随机性,造成评价结果不准确。首先应用齐次坐标变换,推导了改进Delta并联机构的位置反解公式。基于位置反解和一阶泰勒展开,建立了包含机构尺寸误差、转动副间隙误差和驱动误差的机构位置误差计算模型。利用该误差模型,考虑各个原始输入误差的随机性,推导了机构运动可靠性数学模型,给出了评价机构运动可靠性高低的量度和计算方法。运动可靠性是机构运动精度高低的更本质的衡量指标。运动可靠性分析是机构优化设计和误差补偿的基础。     

含旋转铰间隙平面运动机构可靠性灵敏度分析

基于时变运动机构可靠性灵敏度分析方法,考虑机构杆件旋转铰间隙对运动精度的影响,发展出一种计算含旋转铰间隙平面运动机构全局灵敏度指标的分析方法。该方法首先基于该种运动机构的误差函数构建其包络函数,进而解析推导其可靠性计算公式,在此基础上结合时变运动机构全局灵敏度分析方法,求得含旋转铰间隙平面运动机构各全局灵敏度指标的计算公式。最后,将本文所提方法应用到两个具体机构算例,所得结果数据与蒙特卡罗法计算结果相比吻合度高,具有较高的精确度;同时,计算成本也大大降低。     

应用于飞机装配的并联机构技术发展综述

并联机构的闭链结构使其具有良好的精度、刚性及动态性能，可满足飞机装配的精度、效率需求，因此，以并联机构为构型主体的自动化装配装备正越来越多地应用于飞机装配中。首先，概述了当前并联机构发展现状及飞机装配体现出的新特点，分析了并联机构应用于飞机装配的优势。其次，从飞机装配零部件加工和飞机零部件装配调姿定位两个方面综述了应用于飞机装配并联机构的国内外发展现状。然后，探讨了并联机构主要的前沿研究问题，从并联机构可重构设计、性能评价及优化设计、精度建模和力/位协同控制等4个方面，详细分析了并联机构应用于飞机装配中的关键技术。最后，对并联机构应用在飞机装配中未来的发展方向和机遇做了展望。     

一种共轴式直升机操纵机构的运动学建模与分析

 共轴式直升机操纵机构的输入/输出运动学关系复杂、非线性严重,不同通道间控制耦合大,其中航向采用全差动的操纵机构最为复杂。为了分析用比例关系简化建模所引起的误差及利用逆运动学进行操纵系统线性化,必须对操纵机构运动学进行精确建模。针对一种航向全差动操纵机构,首先,运用机构学原理,通过去除过约束、局部自由度对机构进行简化,计算得到操纵机构自由度;然后,将操纵机构分为3个子模块,通过对每个模块应用空间机构位置分析方法进行正向、逆向运动学推导,建立系统完整的运动学模型;利用光学测量原理设计了测试系统,并通过实验验证了所建模型的正确性;最后给出了所建模型在共轴式直升机建模、操纵解耦及线性化方面的应用方法。     

可重构混联机械手——Tricept的自标定方法

由于并联构型装备难于实现全闭环反馈控制,使运动学标定成为一项具有显著经济价值并十分有效的提高并联构型装备精度的手段,通常包括误差建模、测量、辨识和补偿4个环节。基于以上因素,以5自由度混联机械手Tricept为对象,研究一种基于内部传感器检测信息的运动学标定方法。首先建立传感器测量值与影响末端可补偿位姿误差的几何误差源的映射关系。在此基础上,讨论了几何误差的可辨识性。通过计算机仿真验证了所提方法的可行性和有效性。     

Accuracy enhancement of the spherical actuator with a two-level geometric calibration method

This paper presents a two-level geometric calibration method for the permanent magnet （PM） spherical actuator to improve its motion control accuracy. The proposed actuator is com- posed of a stator with circumferential coils and a rotor with multiple PM poles. Due to the assembly and fabrication errors, the real geometric parameters of the actuator will deviate from their design values. Hence, the identification of such errors is critical for the motion control tasks. A two-level geometric calibration approach is proposed to identify such errors. In the first level, the calibration model is formulated based on the differential form of the kinematic equation, which is to identify the geometric errors in the spherical joint. In the second level, the calibration model is formulated based on the differential form of torque formula, which is to calibrate the geometric parameters of the magnetization axes of PM poles and coils axes. To demonstrate the robustness and availability of the calibration algorithm, simulations are conducted. The results have shown that the proposed two-level calibration method can effectively compensate the geometric parameter errors and improve the positioning accuracy of the spherical actuator.     

Influence of deformation zone length on bending radius of SS304 tubes with small diameters manufactured via free bending-based active motion

In three and six-axis free-bending equipment, the deformation zone length(A) is a fixed mechanical structure parameter modified when the relevant structure is redesigned and manufactured. In this study, a six degree of freedom(6-DOF) parallel mechanism was used as the control mechanism of the bending die, and a new method of changing the deformation zone length(A)was proposed. Firstly, an idealized geometric model of free bending-based active motion was established. Then, the influence of the de...     

高分影像辅助下的航空高光谱严密几何检校方法

 惯性测量单元(IMU)与传感器视准轴的偏心角和偏心矢量是造成航空线阵列高光谱数据几何校正误差的主要原因之一。在分析偏心角与偏心矢量误差来源之后提出该误差由IMU主轴与传感器主轴的角度偏差、测区固定偏差、GPS中心与传感器投影中心相对偏差组成,在此基础上建立了较为严密的检校模型。针对模型解算时需要大量高精度控制点的问题,提出了一种高分影像辅助下的亚像元精度控制点自动提取方法。通过多地区、多传感器高光谱航测实验表明,亚像元精度控制点能有效提高模型解算精度。新检校模型可获得亚像元校正精度,推扫式传感器——应用型机载成像光谱仪(AISA)建模中误差约为0.39个像元,摆扫式传感器——实用型模块化成像光谱仪(OMIS)建模中误差约为0.23个像元,校正后的影像可直接进行拼接。     

平面磨削形状误差的分析

提出了平面磨削形状误差的产生模型,并通过实验验证了其模型的合理性,同时揭示了各种要素对形状误差的影响规律,选定了能使形状误差最小的磨削加工条件。     

面向再入目标跟踪的估计与辨识联合优化算法

准确的弹道系数辨识和精确的目标状态估计是再入目标高精度跟踪与高可靠识别的关键。一方面,状态估计的误差会造成模型参数(弹道系数)的辨识风险;另一方面,模型参数的辨识偏差又会导致模型失配从而降低目标状态的估计精度。因此,需要实现再入目标的状态估计和参数辨识的联合优化。针对再入目标弹道系数未知情形,提出了一种基于期望最大化(EM)框架并采用粒子滤波(PF)平滑器实现的PF-EM联合优化算法。在E步基于粒子平滑器得到目标状态的后验平滑估计,M步采用数值优化算法更新上一次迭代的弹道系数,通过E步和M步的不断迭代,以保证状态估计和弹道系数辨识的一致性。算法仿真对比表明:所提算法的状态估计和参数辨识精度均优于传统的状态增广算法。     

Fuzzy adaptive robust control for space robot considering the effect of the gravity

Space robot is assembled and tested in gravity environment, and completes on-orbit service（OOS） in microgravity environment. The kinematic and dynamic characteristic of the robot will change with the variations of gravity in different working condition. Fully considering the change of kinematic and dynamic models caused by the change of gravity environment, a fuzzy adaptive robust control（FARC） strategy which is adaptive to these model variations is put forward for trajectory tracking control of space robot. A fuzzy algorithm is employed to approximate the nonlinear uncertainties in the model, adaptive laws of the parameters are constructed, and the approximation error is compensated by using a robust control algorithm. The stability of the control system is guaranteed based on the Lyapunov theory and the trajectory tracking control simulation is performed. The simulation results are compared with the proportional plus derivative（PD） controller, and the effectiveness to achieve better trajectory tracking performance under different gravity environment without changing the control parameters and the advantage of the proposed controller are verified.     

基于3RRS-Bricard复合空间捕获系统运动学分析

面向跨尺度、目标多样化的空间捕获任务,融合Bricard和3RRS机构的折展特性和几何特点对复合捕获系统运动学进行了分析。基于捕获系统的自由度和构型特点分析,通过构建Bricard与3RRS间的转换关系实现了捕获系统各机构间的运动学解耦。根据六棱柱模型,引入Bricard虚拟顶点,设计了面向复合空间捕获系统的运动学求解方法。在仿真环境下搭建捕获系统的运动学和动力学模型,并开展针对动态捕获目标的轨迹跟随实验。通过与基于闭环约束的阻尼最小二乘法（DLS）对比,验证了该运动学求解算法的有效性和先进性。实验结果表明,捕获系统可实现平稳的协同控制,运动过程中位置跟随精度优于4 mm,姿态精度优于0.035 rad。     

Multipath Fluctuation Effects in Track-While-Scan Radar

A theoretical model of diffuse multipath reflections from rough surfaces is applied to the prediction of multipath power distribu tions in radar coordinates: elevation angle, time delay, and Dop pler frequency. These distributions are used to predict radar tracking errors in elevation angle, for both monopulse and scan ning antenna systems, and typical results are presented. These show a small increase in tracking error for scanning systems, on radially approaching targets, caused by sensitivity of these trackers to amplitude scintillation of the composite direct-plus multipath signal. Effects of knife-edge diffraction and of vegetation ion are briefly considered.     

偏置式Delta并联机构的运动学分析

 具有3 个平移自由度的Delta 并联机构因所有运动副均采用转动铰链而愈来愈引起研究者的重视。偏置量的存在虽降低了加工、制造、装配的难度,但其运动学分析的难度大大增加。本文利用消元法对偏置式Delta 并联机构的正逆运动学进行了深入分析,求出了所有数值解。并采用几何图解法验证了位置正逆解的正确性。在运动学分析过程中引入了矢量分析,使得消元法求解过程十分简便。通过偏置式Delta 并联机构的运动学分析可以证明,某些观点并不准确。     

Configuration synthesis of planar folded and common overconstrained spatial rectangular pyramid deployable truss units

Compared with non-overconstrained deployable units, overconstrained deployable units are widely used in space missions for their higher stiffness characteristics. Besides the performance of a three-step topological structural analysis and design of the rectangular pyramid deployable truss unit(PDTU), conducting a structural synthesis of an overconstrained deployable unit requires the determination of the relative position and direction of each kinematic axis. The structural synthesis of an overconstrained deployable unit is investigated based on screw theory and its topological structure. The possible overconstrained cases of the rectangular PDTUs are analyzed, and corresponding screw expressions are obtained. Thus, the rectangular PDTUs, which can be folded into a plane, are synthesized systemically, and a series of overconstrained rectangular PDTUs is obtained. Furthermore, the feasibility of the folded and deployed motions under one degree of freedom for those deployable units is verified in dynamical simulation by using ADAMS 2010.     

Systematic Geometric Error Modeling for Workspace Volumetric Calibration of a 5-axis Turbine Blade Grinding Machine

A systematic geometric model has been presented for calibration of a newly designed 5-axis turbine blade grinding machine. This machine is designed to serve a specific purpose to attain high accuracy and high efficiency grinding of turbine blades by eliminating the hand grinding process. Although its topology is RPPPR (P: prismatic; R: rotary), its design is quite distinct from the competitive machine tools. As error quantification is the only way to investigate, maintain and improve its accuracy, calibration is recommended for its performance assessment and acceptance testing. Systematic geometric error modeling technique is implemented and 52 position dependent and position independent errors are identified while considering the machine as five rigid bodies by eliminating the set-up errors of workpiece and cutting tool. 39 of them are found to have influential errors and are accommodated for finding the resultant effect between the cutting tool and the workpiece in workspace volume. Rigid body kinematics techniques and homogenous transformation matrices are used for error synthesis.     

捕获轨迹系统并联机构地面标定方法

捕获轨迹系统（CTS）是一种先进的预测外挂物投放轨迹的试验系统，普遍采用六自由度（6-DoF）串联机构作为其运动机构，串联机构因惯性力大和关节累积误差大使其定位精准度不足。相比串联机构，并联机构具有惯性力小和关节误差不累积等优点。采用6-PTRT并联机构作为CTS试验系统的六自由度运动机构，在空间受限的风洞环境中对CTS并联机构进行地面标定：提出动平台位姿的测量和计算方法，建立包含直线驱动平台安装夹角修正的标定模型，并基于非线性最小二乘法辨识结构参数。辨识后CTS并联机构的位移定位准度优于0.1 mm，姿态定位准度优于0.05°，最后以CTS并联机构和常规攻角机构进行8#标模的对比风洞试验。风洞试验结果表明，CTS并联机构的风载定位准度满足测力试验精准度要求。     

相控阵雷达长时跟踪波束调度与波形优化策略

针对相控阵雷达多目标跟踪波束调度和波形参数优化控制的问题，本文提出了一种基于马尔可夫决策过程（MDP）的相控阵雷达跟踪波束调度与波形参数优化策略，该方法以无迹卡尔曼滤波（UKF）算法为基础来估计目标的状态。首先将本文的序列决策问题建模为马尔可夫决策过程，定义了资源的效费比和长期回报率，然后与当前实际跟踪误差综合考虑作为MDP的回报函数，进而给出了调度的优化模型，最后将长时决策问题转化为动态规划算法结构进行求解，并且提出了一种并行混合遗传粒子群优化算法来求解各决策时刻的最优策略。仿真结果表明了长时策略的先进性以及寻优算法的优越性，与传统的短时策略相比，跟踪精度可提高11.17%。     

The Scientific Measurement System of the Gravity Recovery and Interior Laboratory (GRAIL) Mission

The Gravity Recovery and Interior Laboratory (GRAIL) mission to the Moon utilized an integrated scientific measurement system comprised of flight, ground, mission, and data system elements in order to meet the end-to-end performance required to achieve its scientific objectives. Modeling and simulation efforts were carried out early in the mission that influenced and optimized the design, implementation, and testing of these elements. Because the two prime scientific observables, range between the two spacecraft and range rates between each spacecraft and ground stations, can be affected by the performance of any element of the mission, we treated every element as part of an extended science instrument, a science system. All simulations and modeling took into account the design and configuration of each element to compute the expected performance and error budgets. In the process, scientific requirements were converted to engineering specifications that became the primary drivers for development and testing. Extensive simulations demonstrated that the scientific objectives could in most cases be met with significant margin. Errors are grouped into dynamic or kinematic sources and the largest source of non-gravitational error comes from spacecraft thermal radiation. With all error models included, the baseline solution shows that estimation of the lunar gravity field is robust against both dynamic and kinematic errors and a nominal field of degree 300 or better could be achieved according to the scaled Kaula rule for the Moon. The core signature is more sensitive to modeling errors and can be recovered with a small margin.