直线模拟加载系统的研究进展与发展趋势

直线模拟加载系统是一种用于在实验室条件下模拟承载对象工作时所受直线负载力的半实物仿真系统，可用于模拟各类飞行器关键部件在工作过程中所受的气体阻力载荷。针对目前常用的机械式、电液式和电动式直线模拟加载系统，分析其基本加载原理和研究进展，结合自行研制的电动式直线模拟加载系统进行了深入探讨。针对多余力抑制方法的关键问题，详细论述了直线负载模拟器的结构补偿方法和控制策略。最后，展望了直线模拟加载系统的发展趋势，归纳了电动式直线模拟加载系统的高精度、大载荷发展方向。     

基于有限Fourier级数的航天器转移轨迹设计

针对航天器小推力转移轨迹的初始设计问题，利用基于三阶Fourier级数的设计方法实现了航天器小推力的多圈转移。同时，基于有限Fourier级数的形状法，对具有多个约束条件的小推力多圈转移轨迹进行了优化设计。选取了共面同轴同偏心率的初始和末端轨道位置，对所提出的方法进行了仿真验证。结果表明：与改进逆五阶多项式形状法相比，所提出的方法虽然增加了转移时间，但当转移圈数为5圈、有限Fourier级数的项数为10时，可减少将近75%的转移速度增量，同时大大减小了所需的最大推力加速度的值。     

Cutting path-dependent machinability of SiCp/Al composite under multi-step ultra-precision diamond cutting

Particle-tool interactions, which govern the synergetic deformation of SiC particle reinforced Al matrix composites under mechanical machining, strongly depend on the geometry of particle position residing on cutting path. In the present work, we investigate the influence of cutting path on the machinability of a SiCp/Al composite in multi-step ultra-precision diamond cutting by combining finite element simulations with experimental observations and characterization. Be consistent with experimentally characterized microstructures, the simulated SiCp/Al composite is considered to be composed of randomly distributed polygonally-shaped SiC particles with a volume fraction of 25vol%. A multi-step cutting strategy with depths of cut ranging from 2 to 10 μm is adopted to achieve an ultimate depth of cut of 10 μm. Intrinsic material parameters and extrinsic cutting conditions utilized in finite element simulations of SiCp/Al cutting are consistent with those used in corresponding experiments. Simulation results reveal different particle-tool interactions and failure modes of SiC particles, as well as their correlations with machining force evolution, residual stress distribution and machined surface topography. A detailed comparison between numerical simulation results and experimental data of multi-step diamond cutting of SiCp/Al composite reveals a substantial impact of the number of cutting steps on particle-tool interactions and machined surface quality. These findings provide guidelines for achieving high surface finish of SiCp/Al composites by ultra-precision diamond cutting.     

小卫星侦察星座性能评估研究

针对小卫星侦察星座性能评估问题，从覆盖、成本和弹性三方面对小卫星侦察星座的性能指标进行研究，分别构建了考虑存储容量约束的覆盖能力评估模型、成本估计模型以及弹性能力评估模型。在覆盖能力评估模型中，将卫星存储容量作为约束条件，结合卫星覆盖几何模型分析了卫星对地侦察的工作条件，提出考虑存储容量的覆盖指标计算方法；通过小卫星成本模型(small satellite cost model,SSCM)对星座各分系统的成本进行估计；在弹性评估模型中，提出了星座性能损失率指标，并根据星座失效状态概率函数确定了不同失效状态下星座性能损失率的权重。将上述模型应用于SkySat和吉林一号星座的性能评估过程中，结果表明SkySat比吉林一号覆盖能力强、成本低，弹性差。提出的三个模型可用于评价星座优劣，为小卫星侦察星座的建设和性能评估工作提供参考。     

飞秒激光系统图像调焦装置以及方法

飞秒激光直写技术在复杂三维微结构加工领域具有显著优势，而调焦是否精准直接影响了所加工结构的完整度.提出了在光路中临时置入调焦光源和物的图像调焦技术，通过调节物的位置使其成像面与激光聚焦面一致，从而通过清晰可分辨的成像状态间接反映激光聚焦状态.利用Zemax软件模拟分析了原飞秒激光光路与加入调焦光源和物的调焦光路，二者可实现相同加工物镜后工作距离与良好成像质量，证明了该方法的可行性.通过分析得到该过程的成像误差主要由成像镜头焦深(3.9 μm)引起，我们获得的理想调焦精度可达到1/2焦深以内.设计了单层高度为5 μm的二层圆柱结构，通过多次实验验证了所加工元件高度误差在1.5 μm范围以内，与理论分析一致，满足飞秒激光系统的调焦要求.     

考虑根铰间隙的空间框架展开机构动力学分析

利用Kane法多体动力学基本理论并考虑根铰间隙影响因素，建立适用于空间柔性太阳电池阵的多框架展开机构多体系统动力学模型，对框架展开机构的展开方式和展开过程进行仿真分析，获得了机构组成部件在展开过程中的几何位置、速度、加速度等动力学特性，分析了框架展开机构各个关节点运动特性、铰链间隙与外部驱动力的相互作用规律。结果表明：合理控制框架展开机构各运动部件的驱动力矩是保证框架按照确定规律展开的必要条件；根铰间隙对太阳电池阵框架展开机构角加速度影响较为明显，进而影响到展开框架展开过程的稳定性，对转角和角速度几乎没有影响；在进行空间太阳电池阵框架展开机构设计时应严格控制铰链轴间隙，并通过动力学仿真校核间隙对太阳电池阵展开过程的影响；研究结果为空间柔性太阳电池阵多模块框架展开机构设计提供指导。     

A novel architecture of electro-hydrostatic actuator with digital distribution

To address the flow imbalance rapidly of the asymmetric Electro-Hydrostatic Actuator (EHA), this paper presents a novel architecture of asymmetric EHA with the Digital Distribution (EHA-DD). It also improves the flow nonlinearity and control accuracy of the pump, especially in the low-speed condition. The digital distribution with two High-Speed on–off Valves (HSVs) not only balances flow instead of the check valves, but also replaces the pump at the low-speed to control output flow by adjusting the PWM signal. The pump and HSVs are the crucial components to control flow output. Firstly, the flow calculation models of the pump and the duty ratio inversed model of the HSV are obtained through experimental tests and the identification method. To get the control input signal for the required flow, the pump speed and PWM duty ratio for the HSVs are inversed to compensate for flow output. Further, a multimode digital flow distribution control method based on pump speed, mainly including the pump-controlled mode for large flow demand and valve-controlled mode for little flow demand, is proposed to control the accurate flow output actively. The step extension experiments based on the flow calculation models are conducted on the EHA-DD prototype under elastic, opposite varying load. The results demonstrate that the EHA-DD realizes little position error by accurate flow control, and it is also beneficial to improve the service life of the pump.     

同步双小行星系统共振轨道设计

研究了同步双小行星系统中共振轨道的设计方法及演化规律。首先，基于双椭球模型建立探测器运动方程，并给出共振轨道初值选取方法。然后，利用改进并行打靶法，提出一种双小行星系统平面共振轨道两步修正方法。同时结合稳定性理论及分岔理论，给出双小行星系统三维共振轨道生成和延拓方法；最后，以双小行星系统1999KW4为例，设计了共振比为1∶1,1∶2,1∶3,1∶4,2∶3的平面和空间共振轨道族，并分析了共振轨道的特性及轨道周期和轨道能量的变化规律。给出的双小行星系统中共振轨道的设计方法具有普适性，对未来双小行星系统探测任务中的轨道设计具有一定的参考意义与借鉴价值。     

Inverse identification of constitutive parameters of Ti2AlNb intermetallic alloys based on cooperative particle swarm optimization

Ti₂AlNb intermetallic alloy is a relatively newly developed high-temperature-resistant structural material, which is expected to replace nickel-based super alloys for thermally and mechanically stressed components in aeronautic and automotive engines due to its excellent mechanical properties and high strength retention at elevated temperature. The aim of this work is to present a fast and reliable methodology of inverse identification of constitutive model parameters directly from cutting experiments. FE-machining simulations implemented with a modified Johnson-Cook (TANH) constitutive model are performed to establish the robust link between observables and constitutive parameters. A series of orthogonal cutting experiments with varied cutting parameters is carried out to allow an exact comparison to the 2D FE-simulations. A cooperative particle swarm optimization algorithm is developed and implemented into the Matlab programs to identify the enormous constitutive parameters. Results show that the simulation observables (i.e., cutting forces, chip morphologies, cutting temperature) implemented with the identified optimal material constants have high consistency with those obtained from experiments, which illustrates that the FE-machining models using the identified parameters obtained from the proposed methodology could be predicted in a close agreement to the experiments. Considering the wide range of the applied unknown parameters number, the proposed inverse methodology of identifying constitutive equations shows excellent prospect, and it can be used for other newly developed metal materials.     

SSPS-OMEGA超大型球形聚光器结构拓扑构型与设计

为同时兼顾千米量级尺度空间太阳能电站聚光系统的在轨发射安装难度、光学收集效率、稳定性及结构工艺等多方面的因素，提出采用基于球面正多面体的经纬线划分法模块化构建球形聚光器。该方法不仅可实现基础划分单元分布均匀、规格种类少，降低在轨构建与运载发射难度。而且只要合理控制弧高等分数和基础划分单元的口径就可以同时保证聚光系统的光学收集效率。理论与仿真结果显示，当弧高等分数为24时，该划分法共有25种基础单元件，整个球面被分成5762块。并且此时模块化构建的实际球形聚光器的光学收集效率与理想球面相比基本保持不变，解决了太阳能电站聚光系统设计中存在的关键问题。