A new algorithm to optimize Barker code sidelobe suppressionfilters

The authors suggest a new algorithm for binary coding waveform sidelobe reduction after matched filtering and present a general method by which optimized sidelobe suppression filters for Barker codes can be obtained with a peak output sidelobe 2.62 dB lower than the results found in the literature (for 13-b Barker code). This optimization algorithm is also promising for other binary coding waveforms, such as truncated pseudonoise (PN) sequences and concatenated codes. This new approach can readily be applied to sidelobe-reduction filter design for other binary coding waveforms, such as truncated PN sequences, concatenated codes, etc., which often find their applications in radar systems and spread spectrum communication systems     

Optimum Mismatched Filters for Sidelobe Suppression

This paper discusses the application of least-mean-squares approximate inverse filtering techniques to radar range sidelobe reduction. The method is illustrated by application to the 13-element Barker code. The performance of the least-mean-square inverse filter is compared with the matched filter and with the simplified sidelobereducing filters of Rihaczek and Golden. A filter which completely suppresses the range sidelobes of a 13-element Barker sequence is only 0.2 dB worse than a matched filter in noise.     

Modified Barker and Huffman Sequences in Combination Codes

lt is possible that usable combination codes can be obtained if Barker and Huffman sequences are chosen as the inner and outer codes. lt is shown that an improvement in either energy efficiency or time sidelobe structure will result either from a modification of a Huffman sequence or from a modification of a Barker sequence. Results are given for a combination code of length 91, with inner and outer codes of length 7 and 13.     

大多普勒容限巴克码脉压

 本文介绍用补偿式非相干型旁瓣抑制滤波器(SSF)实现13位巴克码脉冲压缩旁瓣抑制的理论计算及实验结果。补偿式非相干型SSF采用最小二乘近似逆滤波方法设计,若子脉冲宽度为0.7μs,峰值旁瓣电平不超过-30dB,这种SSF的多普勒容限能达到-40kHz～+40kHz。理论计算及实验结果都表明,所设计的补偿式非相干型SSF的多普勒容限比具有同样长度冲激响应序列的R-G-ISSF有显著改善。     

Clutter Suppression by Complex Weighting of Coherent Pulse Trains

Uniform coherent pulse trains offer a practical solution to the problem of designing a radar signal possessing both high range and range-rate resolution. The Doppler sensitivity provides some rejection of off-Doppler (clutter) returns in the matched filter receiver. This paper considers the use of a processor in which members of the received pulse train are selectively weighted in amplitude and phase to improve clutter suppression. The techniques described are particularly suitable for rejecting interference entering the processor through ambiguous responses (range sidelobes) of the signal. The complex weights which are derived are optimum in the sense that they produce the maximum clutter suppression for a given detection efficiency. In determining these weights, it is assumed that the distribution of clutter in range and range rate relative to targets of interest is known. Thus, clutter suppression is achieved by reducing the sidelobe levels in specified regions of the receiver response. These techniques are directly applicable to array antennas; the analogous antenna problem would be to reduce sidelobe levels in a particular sector while preserving gain. Complex weighting is most successful when the clutter is limited in both range and velocity.     

Poly-phase codes and optimal filters for multiple user ranging

A technique is introduced to select poly-phase codes and optimal filters of a pulse compression system that have specific temporal and frequency characteristics. In the particular problem under study, multiple vehicles are assigned unique codes and receiver filters that have nearly orthogonal signatures. Narrowband users, that act as interference, are also present within the system. A code selection algorithm is used to select codes which have low autocorrelation sidelobes and low cross correlation peaks. Optimal mismatched filters are designed for these codes which minimize the peak values in the autocorrelation and the cross correlation functions. An adjustment to the filter design technique produces filters with nulls in their frequency response, in addition to having low correlation peaks. The method produces good codes and filters for a four-user system with length 34 four-phase codes. There is considerable improvement in cross and autocorrelation sidelobe levels over the matched filter case with only a slight decrease in the signal-to-noise ratio (SNR) of the system. The mismatched filter design also allows the design of frequency nulls at any frequency with arbitrary null attenuation, null width, and sidelobe level, at the cost of a slight decrease in processing gain     

Effect of Particular Gain Changes upon LFM Sidelobes

The envelope variation of an LFM waveform due to transmitter droop or receiver STC tends to cause range sidelobes. A parametric analysis of the magnitude of the sidelobes has been performed. It is shown that the sidelobes can be quite high at the matched filter output, but are low at the output of the sidelobe reduction filter. 40-dB sidelobes can be achieved even with a 4-dB envelope droop. It is shown that these results are consistent with conventional paired-echo theory. Similar results are shown to hold for droop variations of the filter transfer function.     

Reciprocal radar waveforms

Digitally coded radar waveforms can be used to obtain large time-bandwidth products (pulse compression ratios). It is demonstrated that periodic radar waveforms with zero sidelobes or almost zero sidelobes can be defined. A perfect periodic code is a periodic code whose autocorrelation function has zero sidelobes and whose amplitude is uniform (maximum power efficiency=1). An asymptotically perfect periodic code has the property that as the number of elements in the code goes to infinity the autocorrelation function of the code has zero sidelobes and its power efficiency is one. The authors introduce a class of radar waveforms that are either perfect or asymptotically perfect codes. These are called reciprocal codes because they can be derived through a linear transformation of known codes. The aperiodic performance of the reciprocal code is examined     

Reduction of sidelobe self-interference in an agile beam radar

In an agile beam phased array radar, the beam is often multiplexed over several angular positions, and “listens” in each position only over an instrumented range that may be a fraction of the unambiguous range as determined by the pulse repetition period in each position. After transmitting a pulse in a given direction, the beam is switched, essentially instantaneously, to another position, after the instrumented range delay. In this second position, echoes from the first position, from multiple trips of the instrumented range, enter the one-way angular sidelobes of the first position. This interference is compounded if there are several beam positions in a pulse repetition period. The author proposes a method of phase coding the pulses in such a way that the pulse-to-pulse phase variation in each direction is orthogonal to every other phase code in the other directions. The codes are Walsh functions. These are sets of binary valued (+1 or -1) functions such that all of the functions in the set are mutually orthogonal. Not every possible number N of pulses in each direction and number K of beam positions can be accommodated, but a large variety of such combinations can be accommodated. Several examples are given. The combination of low one-way sidelobes and orthogonality (or near orthogonality) of the phase codes should provide for very stringent sidelobe self interference rejection     

Quasi-Complementary Sequences

A method of constructing digital phase reversal codes which have few nonzero sidelobes and which are available in frequent lengths is given. This is particularly important in the area of longer codes. The codes are a form of combined sequence and, hence, have the desirable property of bandwidth reduction for the outer code. However, only two member codes are required. A major usage of these codes may be in addressing.     

Digital and Analog Subcomplementary Sequences for Pulse Compression

Golay's complementary pairing has been a method to increase the utility of binary sequences, because of the temporal sidelobe suppression in the autocorrelation vector summation. Complementary sets of Tseng and Liu and of Hollis exhibit the same effect when several autocorrelations are combined. These complementary pairs and sets of sequences can be extended into long complementary chains by a simple transformation. This transformation is extended here to all pulse compression waveforms. By this method, even though analog complementary sequences cannot be formed, a new class of waveforms, called subcomplementary waveforms, can be formed. Following these rules, repetition of waveforms such as linear frequency modulation (LFM) or linear stepped frequency modulation (LSFM) in a prescribed manner is possible without creating autocorrelation grating lobes or repetitive sidelobes. This method is equally applicable to all analog or digital pulse compression waveforms.     

Properties of Dolph-Chebyshev Weighting Functions

Dolph-Chebyshev amplitude weighting is used with FFT signal processors and array antennas when a low sidelobe response is required. This particular weighting minimizes the width of the mainlobe response while forcing all of the sidelobes to a specified sidelobe level. As the specified sidelobe level is reduced, the mainlobe width increases, as does the loss in signal-to-noise ratio. This correspondence describes how the Dolph-Chebyshev weights may be easily calculated, and gives design data showing how signal-to-noise loss and mainlobe width vary with the specified sidelobe level.     

两种自适应方向图峰值副瓣控制方法比较

自适应阵列（或称自适应波束形成）目前已广泛应用到雷达、声纳和通信领域中用来抑制各种干扰（有意的干扰，杂波干扰和多用户干扰等）。在雷达应用中，为了减轻脉冲欺骗式干扰或旁瓣目标并利用单脉冲雷达来准确测量目标波达方向．要求自适应方向图具有低副瓣和稳定的主瓣形状。在实际应用中，各种失配误差将降低自适应阵列的性能．这些误差包括由于目标的波达方向不精确引起的信号指向误差，由通道失配和位置扰动引起的阵列校准误差和由小样本教引起的协方差矩阵估计误差。在此情况下，自适应波束形成的性能大大下降（干扰抑制性能变差。主瓣失真和高的副瓣）。已提出了一种基于二次约束的集成峰值副瓣控制（integrated peak sidelobe control，简称IPSC）方法。该方法可以精确地控制峰值副瓣电平并产生具有稳定的主瓣形状的自适应方向图。研究IPSC中目标信号的影响和信号消除方案以进一步提高IPSC的性能。并将IPSC方法和最新提出的基于二阶锥规划（second-order cone programming，简称SOCP）的分布式峰值副瓣控制（distfibuted peak sidelobe control，简称为DPSC）新方法在性能上进行了比较。仿真结果表明。在干扰抑制性能和方向图控制质量方面IPSC比DPSC性能优越。此外IPSC比DPSC计算高效。     

A New Class of Polyphase Pulse Compression Codes and Techniques

A new class of symmetric radar pulse compression polyphase codes is introduced which is compatible with digital signal processing. These codes share many of the useful properties of the Frank polyphase code. In contrast with the Frank code, the new codes are not subject to mainlobe to sidelobe ratio degradation caused by bandlimiting prior to sampling and digital pulse compression. It is shown that bandlimiting the new codes prior to pulse compression acts as a waveform amplitude weighting which has the effect of increasing the mainlobe to sidelobe ratios.     

Minimum Peak Range Sidelobe Filters for Binary Phase-Coded Waveforms

Linear programming techniques are utilized to determine the optimal filter weights for minimizing the peak range sidelobes of a binary phase-coded waveform. The resulting filter is compared with the filter obtained by use of the least square approximation to the ideal inverse filter. For a test case using the 13-element Barker code the linear programming filter is found to have peak sidelobes as much as 5 dB lower than the least squares filter of the same length.     

Sparse frequency transmit-and-receive waveform design

A computationally efficient algorithm derives complex digital transmit and receive ultra-wideband radar and communication waveforms with excellent arbitrary frequency band suppression and range sidelobe minimization. The transmit waveform minimizes a scalar function penalizing weighted spectral energy in arbitrary frequency bands. Near constant power results from another penalty function for deviations from constant power, or constant power is enforced by a phase-only formulation. Next, a least squares solution for the receive waveform minimizes a weighted sum of suppressed band spectral energy and range sidelobes (for pulse and continuous wave operation), with a mainlobe response constraint. Both waveforms are calculated by iterative algorithms whose updates require only linear order in memory and computation, permitting quick calculation of long pulses with thousands of samples.     

Array shape estimation tracking using active sonar reverberation

This paper concerns the problem of array shape estimation and tracking for towed active sonar arrays, using received reverberation returns from a single transmitted CW pulse. Uniform linear arrays (ULAs) deviate from their nominal geometry while being towed due to ship maneuvers as well as ocean currents. In such scenarios, conventional beamforming performed under the assumption of a ULA can sometimes lead to unacceptably high spatial sidelobes. The reverberation leaking through the sidelobes can potentially mask weak targets in Doppler, especially when the target Doppler is close to that of the mainlobe reverberation and the reverberation-to-target ratio (RTR) is very high. Although heading sensors located along the array can be used to provide shape estimates, they may not be sufficiently available or accurate to provide the required sidelobe levels. We propose an array shape calibration algorithm using multipath reverberation returns from each ping as a distributed source of opportunity. More specifically, a maximum likelihood (ML) array shape calibration algorithm is developed, which exploits a deterministic relationship between the reverberation spatial and Doppler frequencies causing it to be low rank in the space-time vector space formed across a single coherent processing interval (CPI). In this application, a sequence of overlapped CPI length snapshots of duration less than the CW pulse is used. The ML estimates obtained for each snapshot are tracked using a Kalman filter with a state equation corresponding to the water pulley model for array dynamics. Simulations performed using real heading sensor data in conjunction with simulated reverberation suggest that 8-10 dB improvement in sidelobe level may be possible using the proposed array shape tracking algorithm versus an algorithm that uses only the available heading information.     

An extended chirp scaling algorithm for spaceborne sliding spotlight synthetic aperture radar imaging

A system impulse response with low sidelobes is critical in synthetic aperture radar（SAR） images because sidelobes contribute to noise and interfere with nearby scatterers. However,the conventional tricks of sidelobe suppression are unable to be exactly applied to the case of spaceborne sliding spotlight SAR due to great azimuth shifts in both time and frequency domains. In this paper, an extended chirp scaling algorithm is presented for spaceborne sliding spotlight SAR data imaging. The proposed algorithm firstly uses the spectral analysis（SPECAN） technique to avoid the azimuth spectrum folding effect and then employs the chirp scaling（CS） algorithm to achieve data focusing, i.e., the so-called two-step approach. To suppress the sidelobe level, an efficient strategy for the azimuth spectral weighting which only involves matrix multiplications and short fast Fourier transformations（FFTs） is proposed, which is a post-process executed on the focused SAR image and particularly simple to be implemented. The SAR image processed by the proposed extended CS algorithm is very precise and perfectly phase-preserving. In the end, computer simulation results verify the analysis and confirm the validity of the proposed algorithm.     

Performance of Sidelobe Blanking Systems

Sidelobe blanking systems are useful in preventing acquisition of strong targets in the antenna sidelobes and also in rejecting pulsed interference originating in the sidelobes. The analysis of a common two-channel system is presented in which the relationship between the probability of main-lobe detection and the probability of sidelobe detection are given in terms of false-alarm probability, signal-to-noise ratio, and the ratio of sidelobe levels of the two channels. The numerical results given provide a basis for the selection of the sidelobe blanking channel antenna gain and threshold levels.     

Range sidelobe reduction for the quadriphase codes

Filters that reduce the sidelobes of the quadriphase-coded waveform are realized by applying the biphase-to-quadriphase transformation to the filter designs that reduce the sidelobes of the prototype biphase code. The mismatch loss is invariant under this transformation, but the resulting peak-to-sidelobe ratio (PSR) can decrease 1.5 dB maximum. An example illustrates the procedure for a compressor composed of a sidelobe reducing filter cascaded with the matched filter and a compressor realized as one mismatched filter