Sidelobe blanking with integration and target fluctuation

In radar systems, sidelobe blanking (SLB) is used to mitigate impulsive interference that enters the radar through sidelobes of the main antenna. SLB employs an auxiliary antenna channel with the output being compared with that of the main antenna channel and a decision is then made as to whether or not to blank the main channel output. SLB performance determination involves the evaluation of several probability functions. Based on the classical Maisel SLB architecture, this work extends previous performance results, in which detection was limited to the case of a single radar pulse with either Marcum or Swerling I target fluctuation. Probability expressions have been generalized to include both an arbitrary number of integrated pulses and target fluctuation models based on the gamma distribution. The Swerling fluctuation models are all special cases of the gamma distribution. Results are derived in terms of two generalized probability functions, one for detection and the other for blanking. With these generalized probability functions, the SLB design and performance results can be determined. Examples are presented and discussed.     

A new CFAR sidelobe canceler algorithm for radar

Signal or target detection is sometimes complicated by the presence of strong interference. When this interference occurs mainly in the sidelobes of the antenna pattern, a solution to this problem is realized through a sidelobe canceler (SLC) implementation. Since the false-alarm probability is a system parameter of special importance in radar, an interference-canceling technique for radar application should maintain the false-alarm probability constant over a wide range of incident interference power. With the requirements of sidelobe interference cancellation and constant false alarm rate (CFAR), a new algorithm for radar detection in the presence of sidelobe interference is developed from the generalized likelihood ratio test of Neyman-Pearson. In this development, the received interference is modeled as a nonstationary but slowly varying Gaussian random process. Cancellation of the sidelobe interference is based upon a `synchronous' estimate of the spatial covariance of the interference for the range gate being tested. This algorithm provides a fixed false-alarm rate and a fixed threshold which depend only upon the parameters of the algorithm     

Fluctuating Target Detection in Clutter Using Sidelobe Blanking Logic

In an earlier paper, Maisel [6] considered two-channel detection systems using a sidelobe blanking logic when a nonfluctuating target was present. This paper is an extension of the earlier work to include fluctuating targets. The Swerling I, II, III, and IV models are considered when single-pulse detection is of interest. An adaptive threshold procedure is also briefly discussed whereby the probability of false alarm at any given resolution cell is maintained constant, even though the input clutter level may vary from cell to cell or from beam position to beam position. Useful data are presented for detection probabilities in the range 0.5 to 0.9, for false alarm probabilities in the range 104 to 10-8, and for a false detection probability of 0.1 for a sidelobe target yielding an apparent signal to total noise power density ratio of 13.0 dB in the main beam receiver.     

Clutter Suppression by Complex Weighting of Coherent Pulse Trains

Uniform coherent pulse trains offer a practical solution to the problem of designing a radar signal possessing both high range and range-rate resolution. The Doppler sensitivity provides some rejection of off-Doppler (clutter) returns in the matched filter receiver. This paper considers the use of a processor in which members of the received pulse train are selectively weighted in amplitude and phase to improve clutter suppression. The techniques described are particularly suitable for rejecting interference entering the processor through ambiguous responses (range sidelobes) of the signal. The complex weights which are derived are optimum in the sense that they produce the maximum clutter suppression for a given detection efficiency. In determining these weights, it is assumed that the distribution of clutter in range and range rate relative to targets of interest is known. Thus, clutter suppression is achieved by reducing the sidelobe levels in specified regions of the receiver response. These techniques are directly applicable to array antennas; the analogous antenna problem would be to reduce sidelobe levels in a particular sector while preserving gain. Complex weighting is most successful when the clutter is limited in both range and velocity.     

Radar Performance Review in Clear and Jamming Environments

The performance of electronically scanned radar systems is evaluated for clear and barrage jamming environments. Radar figures of merit in jamming are derived for search and track modes and are directly related to antenna pattern relative sidelobe levels. A random sidelobe model is analyzed with various numbers of independent jammers. Probability distributions of detection probability are derived to determine detection performance versus average jamming level and number of jammers.     

On a Specific Performance Limitation of Partially Adaptive Antennas

An analysis shows the performance degradation of a sidelobe cancellation system as the consequence of a basic property of partially adaptive antennas when neighboring interference directions are weighted differently in sign by the radar antenna sidelobes.     

Range Sidelobe Suppression for Barker Codes

The utility of Barker-type phase-reversal codes is extended by the use of sidelobe suppression techniques that can be easily implemented in digital form. It is shown that sidelobe suppression techniques can be found where the tapped delay line used to reduce the sidelobes has only a few distinct tap weights, in which case the complexity of the digital processor is greatly reduced. An example is given where the technique is applied to Barker codes with positive sidelobes, specifically, the 13-element Barker code. If higher pulse compression factors are desired than are obtainable with Barker codes, multistage Barker codes may be used. The sidelobes then may be suppressed for any one or all of the different coding stages.     

Robust SVA method for every sampling rate condition

Linear apodization, or data weighting, is the traditional procedure to improve sidelobe levels in a finite sampled signal at the expense of resolution. New apodization methods, such as spatially variant apodization (SVA), apply nonlinear filtering to the signal in order to completely remove sidelobes without any loss of resolution. However, the results are strongly influenced by signal sampling rate. Some variations which improve results have been previously published, but sidelobe cancellation gets worse since sampling frequency is not settled at Nyquist (or a multiple). This paper presents a new and efficient technique based on SVA that drastically reduces sidelobe levels for every sampling rate condition. The algorithm is, essentially, a parameter optimization of a variant filter for each pixel of the image. A one-dimensional case and a two-dimensional generalization are presented, as well as some applications to target detection capability in a synthetic aperture radar (SAR) system.     

Range sidelobe reduction for the quadriphase codes

Filters that reduce the sidelobes of the quadriphase-coded waveform are realized by applying the biphase-to-quadriphase transformation to the filter designs that reduce the sidelobes of the prototype biphase code. The mismatch loss is invariant under this transformation, but the resulting peak-to-sidelobe ratio (PSR) can decrease 1.5 dB maximum. An example illustrates the procedure for a compressor composed of a sidelobe reducing filter cascaded with the matched filter and a compressor realized as one mismatched filter     

Properties of Dolph-Chebyshev Weighting Functions

Dolph-Chebyshev amplitude weighting is used with FFT signal processors and array antennas when a low sidelobe response is required. This particular weighting minimizes the width of the mainlobe response while forcing all of the sidelobes to a specified sidelobe level. As the specified sidelobe level is reduced, the mainlobe width increases, as does the loss in signal-to-noise ratio. This correspondence describes how the Dolph-Chebyshev weights may be easily calculated, and gives design data showing how signal-to-noise loss and mainlobe width vary with the specified sidelobe level.     

A Practical PRSD System for Multiple Target Detection

A block diagram of a practical system using the sequential detection technique for radar detection of multiple targets is given. The system is designed to obtain better detection probability with a lower value of signal-to-noise ratio for a given false-alarm probability and average transmitted power. The total pulse duration is divided into a number of range elements which are tested for the presence or absence of a target before switching the antenna beam to the next position.     

两种自适应方向图峰值副瓣控制方法比较

自适应阵列（或称自适应波束形成）目前已广泛应用到雷达、声纳和通信领域中用来抑制各种干扰（有意的干扰，杂波干扰和多用户干扰等）。在雷达应用中，为了减轻脉冲欺骗式干扰或旁瓣目标并利用单脉冲雷达来准确测量目标波达方向．要求自适应方向图具有低副瓣和稳定的主瓣形状。在实际应用中，各种失配误差将降低自适应阵列的性能．这些误差包括由于目标的波达方向不精确引起的信号指向误差，由通道失配和位置扰动引起的阵列校准误差和由小样本教引起的协方差矩阵估计误差。在此情况下，自适应波束形成的性能大大下降（干扰抑制性能变差。主瓣失真和高的副瓣）。已提出了一种基于二次约束的集成峰值副瓣控制（integrated peak sidelobe control，简称IPSC）方法。该方法可以精确地控制峰值副瓣电平并产生具有稳定的主瓣形状的自适应方向图。研究IPSC中目标信号的影响和信号消除方案以进一步提高IPSC的性能。并将IPSC方法和最新提出的基于二阶锥规划（second-order cone programming，简称SOCP）的分布式峰值副瓣控制（distfibuted peak sidelobe control，简称为DPSC）新方法在性能上进行了比较。仿真结果表明。在干扰抑制性能和方向图控制质量方面IPSC比DPSC性能优越。此外IPSC比DPSC计算高效。     

Effect of Particular Gain Changes upon LFM Sidelobes

The envelope variation of an LFM waveform due to transmitter droop or receiver STC tends to cause range sidelobes. A parametric analysis of the magnitude of the sidelobes has been performed. It is shown that the sidelobes can be quite high at the matched filter output, but are low at the output of the sidelobe reduction filter. 40-dB sidelobes can be achieved even with a 4-dB envelope droop. It is shown that these results are consistent with conventional paired-echo theory. Similar results are shown to hold for droop variations of the filter transfer function.     

Resolution in Doppler and Acceleration with Coherent Pulse Trains

The resolution properties and clutter performance of a simultaneous Doppler and acceleration measurement are investigated in detail with particular emphasis given to coherent pulse trains. The analysis is based on the concept of a matched-filter receiver, although receiver weighting of the type that reduces Doppler sidelobes is also analyzed in detail. Near the main lobe of the acceleration response is a pedestal-ike sidelobe region, the height of which is about 1/N of the main response lobe power where N is the number of pulses in the train. The extent of this pedestal along the acceleration axis is proportional to N. The acceleration measurement in a clutter environment is best performed when both targets and clutter are confined to this pedestal region, since some response sidelobes outside of this region are extremely large.     

相控阵雷达天线模型及仿真

阐述了相控阵天线仿真的重要性,指出了相控阵天线仿真的主要困难。提出了一种利用阵因子、方向性因子和旁瓣抑制因子分别解决仿真波束形状、天线增益、方向图旁瓣及其变化等3大问题,并进行综合建模和仿真,给出了综合后的仿真模型。该仿真模型保证了理论方面的精度,优化和减少了仿真计算步骤和计算量。利用该仿真模型,给出了宙斯盾系统的AN／SPY-1D雷达天线的仿真计算实例。     

On the Perfomance of Air Traffic Control Radar Beacon System

The sidelobe suppression and improved sidelobe suppression mode performance of terminal and enroute air traffic control radar beacon systems using the existing antenna and a typical improved antenna in the presence of perfectly dielectric flat ground are investigated theoretically. Necessary analytical expressions for various quantities characterizing the system performance have been derived. A general purpose computer program has been developed for the computation and tabulation of these quantities as functions of the elevation angle of the observation point and for different combinations of heights of the directional and omnidirectional antennas of the beacon. Although the discussions given here apply to some specific antenna configurations, the theoretical method developed has more general application in evaluating quantitatively the performance of the beacon system in a given situation.     

Poly-phase codes and optimal filters for multiple user ranging

A technique is introduced to select poly-phase codes and optimal filters of a pulse compression system that have specific temporal and frequency characteristics. In the particular problem under study, multiple vehicles are assigned unique codes and receiver filters that have nearly orthogonal signatures. Narrowband users, that act as interference, are also present within the system. A code selection algorithm is used to select codes which have low autocorrelation sidelobes and low cross correlation peaks. Optimal mismatched filters are designed for these codes which minimize the peak values in the autocorrelation and the cross correlation functions. An adjustment to the filter design technique produces filters with nulls in their frequency response, in addition to having low correlation peaks. The method produces good codes and filters for a four-user system with length 34 four-phase codes. There is considerable improvement in cross and autocorrelation sidelobe levels over the matched filter case with only a slight decrease in the signal-to-noise ratio (SNR) of the system. The mismatched filter design also allows the design of frequency nulls at any frequency with arbitrary null attenuation, null width, and sidelobe level, at the cost of a slight decrease in processing gain     

Array shape estimation tracking using active sonar reverberation

This paper concerns the problem of array shape estimation and tracking for towed active sonar arrays, using received reverberation returns from a single transmitted CW pulse. Uniform linear arrays (ULAs) deviate from their nominal geometry while being towed due to ship maneuvers as well as ocean currents. In such scenarios, conventional beamforming performed under the assumption of a ULA can sometimes lead to unacceptably high spatial sidelobes. The reverberation leaking through the sidelobes can potentially mask weak targets in Doppler, especially when the target Doppler is close to that of the mainlobe reverberation and the reverberation-to-target ratio (RTR) is very high. Although heading sensors located along the array can be used to provide shape estimates, they may not be sufficiently available or accurate to provide the required sidelobe levels. We propose an array shape calibration algorithm using multipath reverberation returns from each ping as a distributed source of opportunity. More specifically, a maximum likelihood (ML) array shape calibration algorithm is developed, which exploits a deterministic relationship between the reverberation spatial and Doppler frequencies causing it to be low rank in the space-time vector space formed across a single coherent processing interval (CPI). In this application, a sequence of overlapped CPI length snapshots of duration less than the CW pulse is used. The ML estimates obtained for each snapshot are tracked using a Kalman filter with a state equation corresponding to the water pulley model for array dynamics. Simulations performed using real heading sensor data in conjunction with simulated reverberation suggest that 8-10 dB improvement in sidelobe level may be possible using the proposed array shape tracking algorithm versus an algorithm that uses only the available heading information.     

A Detection Algorithm for Optical Targets in Clutter

There is active interest in the development of algorithms for detecting weak stationary optical and IR targets in a heavy opticalclutter background. Often only poor detectability of low signal-to-noise ratio (SNR) targets is achieved when the direct correlation method is used. In many cases, this is partly obviated by using detection with correlated reference scenes [1, 2].This paper uses the experimentally justified assumption that most optical clutter can be modeled as a whitened Gaussian randomprocess with a rapidly space-varying mean and a more slowlyvarying covariance [2]. With this assumption, a new constant falsealarm rate (CFAR) detector is developed as an application of the classical generalized maximum likelihood ratio test of Neyman and Pearson. The final CFAR test is a dimensionless ratio. This test exhibits the desirable property that its probability of a false alarm(PFA) is independent of the covariance matrix of the actual noiseencountered. When the underlying noise processes are complex intime, similar considerations can yield a sidelobe canceler CFARdetection criterion for radar and communications. Performance analyses based on the probability of detection (PD)versus signal-to-noise ratio for several given fixed false alarm probabilities are presented. Finally these performance curves are validated by computer simulations of the detection process which use real image data with artificially implanted signals.     

Antenna sidelobes in the presence of flat reflectors

Reflecting surfaces near the antenna may produce surprisingly large sidelobes even if the designed free-space sidelobes in the directions of these surfaces are very small. Calculations of such sidelobes are presented for an example of a linear aperture with a parabolic weighting function for the received signal amplitude