Range Dependent Waveform of an Active Weighted Pulse Compression Receiver

This paper presents the output waveform of a correlation techniquewhich incorporates time domain amplitude weighting and matchedfiltering. This scheme may be used in pulse compression radars wherefine target detail is desired over an increment of range, the rangewindow. Analytic expressions describing the amplitude, phase, andfrequency modulation of the output waveform are obtained for thecosine-squared weighted spectrum, truncated Taylor weighted spectrum,and cosine-cubed weighted spectrum with weighting mismatchas a parameter. The effects of such mismatches on the amplitude,phase, and frequency modulation of the compressed waveform areplotted. However, the methods used to obtain these results are generalenough to obtain output waveforms of other weighting functions similarlymismatched.     

Ambiguity Functions for Quadratic Phase-Coded Pulse Trains

The matched filter ambiguity function is presented for a burst waveform composed of repeated subbursts, each one of which consists of N pulses in which the phase is varied quadratically from pulse to pulse. The resulting ambiguity function exhibits small residual ambiguities along the delay axis separated by the reciprocal of the pulse repetition frequency (PRF). A cross-ambiguity function is derived which reduces these ambiguities to zero amplitude. A third cross-ambiguity function is presented for a receiver matched to a generalized Hamming weighted repeated quadratic burst. The location in the delay/Doppler plane of the waveform ambiguities for these waveforms is compared with that of an uncoded pulse burst.     

Harmonic Radar Systems for Near-Ground In-Foliage Nonlinear Scatterers

The radar transmission equation for a harmonic radar operating over a planar, finite dielectric Earth through foliage is derived for an interesting class of nonlinear scatterers. The received power can typically depend on range to the (-14) power for small objects near the ground. The maximum detection range of a ground-based system is related to all major system parameters: it is most sensitive to polarization, transmit antenna height, and transmit wavelength; moderately sensitive to transmit power and transmit antenna area; and least sensitive to receive antenna area, harmonic scattering cross section, and mode of data processing. For example, there is seen to be a best apportionment of total available aperture area into disjoint transmit and receive apertures which can be well approximated by the equal gain condition. Also, there is seen to be a critical path distance through foliage; at distances less than this, small wavelengths are desirable and, conversely, the upper transmit frequency limit may be set by nonlinear scatterer response. Airborne synthetic aperture radar systems are discussed and quantification of harmonic noise and effects of scatterer fluctuation are made. A useful phenomenological model of a nonlinear scatterer is given that is consistent with some observations and predicts a frequency dependence. Nonlinear scatterer effects on range resolution are discussed.     

Generation Schemes for Wind Power Plants

This paper reviews various electric generation schemes for wind energy conversion suitable for interconnection with a power grid. The schemes can be generally classified as constant speed constant frequency (CSCF) and variable speed constant frequency (VSCF) systems. Historically, only CSCF systems have been used for large power generation in wind power plants. However, with the advent of power electronics and the availability of solid state devices capable of handling large amounts of power, VSCF systems are becoming competitive. Various schemes under each classification are discussed and compared. It is stressed, however, that the optimum choice of the generating scheme is not decided by considering the generator alone. The optimum choice is one which minimizes the cost of energy generated by the wind power plant.     

Design and implementation of an AC active load simulator circuit

An AC active load simulator circuit which can simulate a desired load impedance with a power factor from zero to unity (leading or lagging) for the tested AC source is realized and tested. An interface circuit is designed to compute the simulated current waveform for the load-driver circuit according to the specified program of the system control unit and the measured source frequency and voltage amplitude. Both inductive and capacitive loads can be simulated by adjusting the phase difference between the voltage and current waveforms. A software feedback control approach is employed to adjust the current amplitude and the power factor for the purpose of maintaining the impedance value constant regardless of the variation of the source voltage amplitude     

Radar Waveforms for Suppression of Extended Clutter

A common problem in waveform design is to adapt the transmitted signal to the target environment in order that the interference from extended fields of scatterers is reduced. This problem is investigated here for the special case of detection of a single target in the ``vicinity' of an extended clutter space. The paper considers the possibility of confining the matched-filter response in delay and Doppler, or ambiguity function, to a narrow strip with arbitrary orientation in the delay-Doppler plane. It is shown that strict confinement of the response is achievable only with waveforms that are unlimited in both time and frequency domain. With practical waveforms, which are necessarily of finite extent, one merely can trade close-target separability against detectability in the background clutter. Thus, one form of the resolution problem is exchanged against the other. The paper examines these effects quantitatively.     

New correlated MIMO radar covariance matrix design with low side lobe levels and much lower complexity

In this paper, a new correlated covariance matrix for Multi-Input Multi-Output (MIMO) radar is proposed, which has lower SideLobe Levels (SLLs) compared to the new covariance matrix designs and the well-known multi-antenna radar designs including phased-array, MIMO radar and phased-MIMO radar schemes. It is shown that Binary Phased-Shift Keying (BPSK) waveforms that have constant envelope can be used in a closed-form to realize the proposed covariance matrix. Therefore, there is no need to deploy different types of radio amplifiers in the transmitter which will reduce the cost, considerably. The proposed design allows the same transmit power from each antenna in contrast to the phased-MIMO radar. Moreover, the proposed covariance matrix is full-rank and has the same capability as MIMO radar to identify more targets, simultaneously. Performance of the proposed transmit covariance matrix including receive beampattern and output Signal-to-Interference plus Noise Ratio (SINR) is simulated, which validates analytical results.     

Waveform fusion in sonar signal processing

In active sonar systems, proper selection of the transmitted waveform is critical for target detection and parameter estimation, especially with the existence of clutter (reverberation). Two commonly used waveforms (constant frequency (CF) and linear frequency modulated (LFM)) are studied. Their characteristics are complementary both with respect to their accuracies and their sensitivity to the blind zero-Doppler ridge. Several fusion schemes of the two kinds of waveforms are explored and fusion results are studied both analytically and from simulation. It is concluded that fusion of the information of different waveforms can be not only more robust, but in some cases outright preferable, in term of detection probability and estimation accuracy.     

功率约束下低相关旁瓣的通导一体化波形研究

通信导航一体化是未来无线系统的发展趋势，可以更加充分地利用频谱资源。设计了一种新的一体化波形，在实现通信符号传递的同时，利用其进行时延测距进而实现相应的定位导航功能。一种联合的优化目标函数被提出，其中以星座图上的范数误差衡量通信性能，以自相关函数的加权积分旁瓣电平衡量波形的定时性能。结合一体化系统的实际，在问题求解时同时考虑了波形总功率约束和波形恒模约束，并采用变量交替迭代优化的算法进行迭代求解。最后利用数值仿真验证了算法的有效性。     

功率约束下低相关旁瓣的通导一体化波形研究

通信导航一体化是未来无线系统的发展趋势,可以更加充分地利用频谱资源。设计了一种新的一体化波形,在实现通信符号传递的同时,利用其进行时延测距进而实现相应的定位导航功能。一种联合的优化目标函数被提出,其中以星座图上的范数误差衡量通信性能,以自相关函数的加权积分旁瓣电平衡量波形的定时性能。结合一体化系统的实际,在问题求解时同时考虑了波形总功率约束和波形恒模约束,并采用变量交替迭代优化的算法进行迭代求解。最后利用数值仿真验证了算法的有效性。     

Dwelltime Minimization for Radar Target Detection in the Clear

Consider the design of a minimum dwelltime set of coherent, range-unambiguous pulse bursts that will provide a specified target detection performance in a clutter-free ("clear") range interval [Rmin,Rmax]. Practical procedures are presented here for finding these optimal waveform sets versus Rmax/Rmin, subject to a peak transmit power constraint. It is always possible to design a multiple-PRF clear mode that achieves the same effective use of energy as a single-PRF waveform with a 33 percent duty ratio. Slightly higher effective duty ratios can be achieved if the radar is capable of transmitting and processing two interleaved pulse bursts at the same PRF.     

Pseudorandom Frequency Modulation in Range-Doppler Radar

In many radar systems, efficient use of transmitter power requires the transmission of a constant-amplitude signal for a substantial fraction of time; for a monotonic transmission, however, the range resolution is restricted by the length of the transmitted pulse. Linear frequency modulation removes this constraint for targets with negligible, or known, radial velocities; it is not suitable, however, for simultaneous observations of range and radial velocity (Doppler shift). This paper describes a class of waveforms suitable for simultaneous measurement of range and Doppler shift. These waveforms are characterized by a uniform distribution in frequency and by pseudorandom frequency changes. Uniform frequency distribution is attained by a uniform spacing of frequencies with each frequency present for an identical length of time. Frequency changes are effected by sequencing the frequencies with a pseudorandom number generator. Ambiguity functions are computed for pseudorandom frequencymodulated waveforms designed for ionospheric backscatter studies. By suitable choice of parameters, the ambiguity function becomes a narrow central peak surrounded by a plateau whose height varies randomly between zero and approximately twice its average. Waveform generation by means of a digital frequency synthesizer and data reconstruction considerations are described.     

Transmit Beamforming for MIMO Radar Systems using Signal Cross-Correlation

Proposed next-generation radar systems will have multiple transmit apertures with complete flexibility in the choice of the signals transmitted at each aperture. Here we propose the use of multiple signals with arbitrary cross-correlation matrix R, and show that R can be chosen to achieve or approximate a desired spatial transmit beampattern. Two specific problems are addressed. The first is the constrained optimization problem of finding the value of R which causes the true transmit beampattern to be close in some sense to a desired beampattern. This is approached using convex optimization techniques. The second is the problem of designing multiple constant-modulus waveforms with given cross-correlation R. The use of coded binary phase shift keyed (BPSK) waveforms is considered. A method for finding the code sequences based on random signaling with a structured correlation matrix is proposed. It is also shown that by restricting the class of admissible waveforms one reduces the set of possible signal correlation matrices.     

基于OTR和SHT的射频隐身雷达信号设计

为了提高雷达的射频(RF)隐身性能,结合最优匹配照射-接收机(OTR)理论与序贯假设检验(SHT)方法,提出了一种新的射频隐身雷达信号设计方法。通过发射信号了解外界环境信息,然后反馈这些信息给雷达系统,系统根据这些信息自适应设计雷达发射信号,形成一个闭环系统。以雷达目标识别为具体应用,实验仿真表明,设计的雷达信号自适应变化,减小了信号间的相关性,并且减少了照射次数,降低了辐射功率,从而实现了雷达系统的射频隐身性能。     

小束斑电子束脉冲轰击偏压电源的研制

为了获得一种性价比较高的电子束表面处理技术,采用定频调压电路,研制出一种新型偏压脉冲电源。这种电源由偏压主电路拓扑、偏压变压器和偏压整流滤波电路组成,其中偏压主电路由偏压基值发生电路和偏压脉冲发生电路组成。偏压基值发生电路控制偏压脉冲基值,偏压脉冲发生电路控制偏压脉冲频率和占空比。脉冲偏压电源的脉冲基值、脉冲频率、占空比均连续可调,相应实现脉冲束流的幅值、束流频率和占空比的调节。检测分析了脉冲偏压电源的输出电压波形,带载时的输出束流波形,并观察分析了电子束轰击后钨合金组织变化规律。结果表明所研制的脉冲偏压电源输出电压稳定、可调性好,能满足小束斑脉冲电子束轰击工艺的要求。     

A Domestic Satellite Design

This paper deals with the design parameters of a communications satellite which would be capable of providing domestic telephony, data, and television distribution services. Certain important aspects of the design are discussed, including satellite antenna beam coverage, transponder bandwidth, and transponder radiated power for a given weight range. A baseline satellite design is then presented which has 24 transponders (with 4000 watts radiated power on-axis and 34-MHz radio-frequency bandwidth) fully accessible from the 48 contiguous United States. The design uses crossed linear polarization to reuse the satellite transmit and receive frequency spectrum.     

Design of Optimal Radar Signals Subject to a Fixed Amplitude Constraint

The problem of designing finite-pulse-train radar signals and receivers to maximize the detectability of targets masked by thermal noise and clutter returns is considered in this paper. A practical constraint is introduced: the amplitude of each subpulse in the transmit waveform is taken to be fixed. The need for such a constraint is dictated in most radar applications, because the transmitter is most efficiently utilized by saturating its amplifying tube. An algorithm for generating optimal waveforms subject to this new constraint is presented, and the performance of the resulting waveforms is compared with those obtained using existing optimization techniques.     

Design of Zigzag FM Signals

Since no practical method is available for synthesizing radar waveforms, a sizable effort has been directed into studies of the matched-filter response, or ambiguity function, of many waveforms. In this paper, we investigate the class of FM signals whose instantaneous frequency varies in a zigzag pattern. The waveforms thus consist of linear FM segments and are relatively easy to generate and process. The paper discusses the relation between the characteristics of the waveform and the features of the associated ambiguity function. The effects studied include those of signal repetition, changes in the FM slope, phase-shift and frequency-shift coding, and staggering of frequency step and segment duration. Ambiguity functions of interesting waveforms illustrate the general results. These ambiguity functions are computer-plotted projections of the three-dimensional surface above the delay-Doppler plane.     

Radar/Sonar Signal Design for Bounded Doppler Shifts

In many detection and estimation problems, Doppler frequency shifts are bounded. For clutter or multipath that is uniformly distributed in range and symmetrically distributed in Doppler shift relative to the signal, detectability of a point target or a communication signal is improved by minimizing the weighted volume of the magnitude-squared autoambiguity function. When clutter Doppler shifts are bounded, this volume is in a strip containing the range axis on the range-Doppler plane. For scattering function estimation, e.g., for weather radar, Doppler flow meters, and distributed target classifiers, it is again relevant to minimize ambiguity volume in a strip. Strip volume is minimized by using a pulse train, but such a signal has unacceptably large range sidelobes for most applications. Other waveforms that have relatively small sidelobe level within a strip on the range-Doppler plane, as well as small ambiguity volume in the strip, are obtained. The waveforms are composed of pulse pairs that are phase modulated with Golay complementary codes.