PCD刀具车削不同颗粒含量SiCp/Al复合材料试验研究

碳化硅铝基复合材料具有优良的导热性、较高的比强度和比刚度,在航空航天领域具有广泛的应用前景。由于此复合材料中含有增强相,导致材料的切削加工性能变差。通过试验分析了不同颗粒体积分数(纳米级5%、微米级25%)SiCp/Al复合材料和切削参数(切削速度、背吃刀量、进给量)对刀具磨损和工件表面质量的影响,并对刀具磨损机理进行了研究。试验结果表明,车削微米级25%SiCp/Al材料时聚晶金刚石PCD(Polycrystalline Diamond)刀具磨损更严重,且工件表面质量更差。随着进给量和背吃刀量的增大,工件表面粗糙度值增大,刀片前刀面磨损严重;随着切削速度的增大,工件表面粗糙度值减小,刀片前刀面磨损量增大。选取本文切削参数进行SiCp/Al复合材料的切削加工时,发现刀具磨粒磨损、微崩刃是PCD刀具后刀面磨损的主要成因,且刀具前刀面也会产生积屑瘤。研究结果可为SiCp/Al复合材料PCD车削工艺的优化提供理论基础。     

SiC_p/Al复合材料高速铣削切削力模型建立

使用聚晶金刚石(PCD)刀具并采用正交试验设计法,对含不同体分比的碳化硅颗粒增强铝基复合材料(SiCp/2009Al)进行高速铣削试验。在测量切削力和切屑厚度的基础上,建立了剪切角、剪切应力和摩擦角的预测模型,并结合金属切削基本理论公式建立了切削力的预测模型。该模型包含铣削速度、每齿进给量、径向切宽、增强颗粒体分比等重要参数,模型对进给方向最大铣削力预测值的平均误差为5.9%,对铣刀径向切深方向最大铣削力预测值的平均误差为9.2%,皆高于普通经验公式的预测精度,从而可对SiCp/2009Al复合材料高速铣削时的铣削力进行有效预测。     

Cutting force model and damage formation mechanism in milling of 70wt% Si/Al composite

High-mass fraction silicon aluminium composite(Si/Al composite) has unique properties of high specific strength, low thermal expansion coefficient, excellent wear resistance and weldability. It has attracted many applications in terms of radar communication, aerospace and automobile industry. However, rapid tool wear resulted from high cutting force and hard abrasion, and damaged machined surfaces are the main problem in machining Si/Al composite. This work aims to reveal the mechanisms of milli...     

Effects of in-situ TiB2 particles on machinability and surface integrity in milling of TiB2/2024 and TiB2/7075 Al composites

In-situ ceramics particle reinforced aluminum matrix composites are favored in the aerospace industry due to excellent properties. However, the hard ceramic particles as the reinforcement phase bring challenges to machining. To study the effect of in-situ TiB₂ particles on machinability and surface integrity of TiB₂/2024 composite and TiB₂/7075 composite, milling experiments were performed, and compared with conventional 2024 and 7075 aluminum alloys. In-situ TiB₂ particles clustered at the grain boundaries and dispersed inside the matrix alloy grains hinder the dislocation movement of the matrix alloy. Therefore, the milling force and temperature of the composites are higher than those of the aluminum alloys due to the increase of the strength and the decrease of the plasticity. In the milling of composites, abrasive wear is the main wear form of carbide tools, due to the scratching of hard nano-TiB₂ particles. The composites containing in-situ TiB₂ particles have machining defects such as smearing, micro-scratches, micro-pits and tail on the machined surface. However, in-situ TiB₂ particles impede the plastic deformation of the composites, which greatly reduces cutting edge marks on the machined surface. Therefore, under the same milling parameters, the surface roughness of TiB₂/2024 composite and TiB₂/7075 composite is much less than that of 2024 and 7075 aluminum alloy respectively. Under the milling conditions of this experiment, the machined subsurface has no metamorphic layer, and the microhardness of the machined surface is almost the same as that of the material. Besides, compared with 2024 and 7075 aluminum alloy, machined surfaces of TiB₂/2024 composite and TiB₂/7075 composite both show tensile residual stress or low magnitude of compressive residual stress.     

SiC_(f)/SiC复合材料铣削加工表面质量北大核心CSCD

使用PCD立式铣刀对聚合物浸渍裂解法(PIP)制备的SiC_(f)/SiC复合材料开展单因素铣削试验,通过对加工中产生的切削力和加工后的表面粗糙度进行测量,分析了铣削工艺参数对其的影响;对加工表面、纤维断口进行SEM分析,讨论了SiC_(f)/SiC复合材料加工表面的形成。研究结果表明,表面粗糙度与切削力的变化趋势相同,高主轴转速和小切削宽度有利于得到表面粗糙度较小的加工表面;近孔洞区域与远离孔洞区域的材料去除方式不同;材料中纤维发生面内偏移和层间屈曲,纤维存在多种去除方式。     

SiCp/Al复合材料切削仿真研究

文摘针对SiC_p/Al复合材料的难加工性,建立了二维有限元切削模型,利用ABAQUS完成复合材料正交切削的动态物理仿真。通过仿真与实验结果的比较,验证模型的准确性。同时,利用该切削模型分析颗粒分布形式、直径及刀尖圆弧半径对切削力的影响。结果表明,SiC颗粒的分布形式对切屑形态和切削力具有明显的影响,颗粒形成团簇不利于复合材料加工。切削力随颗粒直径的增大而减小,随刀尖圆弧半径的增大而增大。     

微结构表面超精密加工中切削条件的影响分析

介绍了微结构功能表面加工中的问题,以同轴调制锯齿波微结构的金刚石超精密加工为例阐述了其加工原理,结合试验对刀具刀尖圆弧半径、被加工材料和切削液等切削条件与金刚石超精密切削加工后的微结构功能表面之间的关系进行了分析与讨论,并对主轴转速和刀具进给速度等切削用量与金刚石超精密切削出的微结构功能表面之间的关系进行了分析与讨论.     

高体积分数SiCp/Al复合材料高温压缩界面研究

采用无压浸渗制备出高体积分数SiCp/Al多功能复合材料。对该复合材料进行了高温(高于基体熔点)压缩实验。利用XRD和TEM观察了SiCp/Al复合材料的界面结构,分析了高温压缩对复合材料界面的影响,研究了复合材料的复合机理。结果表明:高温压缩后的SiCp/Al复合材料的界面过渡层连续且厚度均匀,过渡层宽度减小了一个数量级;复合材料SiCp/Al界面结合机制包括扩散、位向和反应结合机制,复合材料SiCp/Al界面的这些结合机制,导致了增强相与基体之间很强的界面结合;复合材料的断裂方式为颗粒断裂,SiC增强颗粒与Al基体结合良好。     

Elliptical vibration cutting of large-size thin-walled curved surface parts of pure iron by using diamond tool with active cutting edge shift

Large-size thin-walled curved surface parts of pure iron are crucial in aerospace, national defense, energy and precision physical experiments. However, the high machining accuracy and surface quality are difficult to achieve due to the serious tool wear and deformation when machining the parts with conventional cutting tools. In this paper, an elliptical vibration cutting (EVC) with active cutting edge shift (ACES) based on a long arbor vibration device is proposed for ultra-precision machining the pure iron parts by using diamond tool. Compared with cutting at a fixed cutting edge, the influence of ACES on the EVC was analyzed. Experiments in EVC of pure iron with ACES were conducted. The evolutions of the surface roughness, surface topography, and chip morphology with tool wear in EVC with ACES are revealed. The reasonable parameters of ultra-precision machining the pure iron parts by EVC with ACES were determined. It shows that the ACES has a slight influence on the machined surface roughness and surface topography. The diamond tool life can be significantly prolonged in EVC of pure iron with ACES than that with a fixed cutting edge, so that high profile accuracy and surface quality could be obtained even at higher nominal cutting speed. A typical thin-walled curved surface pure iron part with diameter ∅240 mm, height 122 mm, and wall thickness 2 mm was fabricated by the presented method, and its profile error and surface roughness achieved PV 2.2 μm and Ra less than 50 nm, respectively.     

SiC晶须增强铝基复合材料超精密切削试验研究

通过聚晶金刚石刀具对SiC晶须增强铝基复合材料SiCw/LD2的超精密切削试验,并用原子力显微镜AFM对加工表面的微观形貌进行检测分析证明:SiCw/Al铝基复合材料的加工表面粗糙度值可以达到超精密级Ra0.01μm,但比切铝基体材料的表面粗糙度值大一级,且粗糙度值随着切削速度的增加、进给量的减小而减小,而吃刀量的影响不大;晶须的破坏方式对加工表面粗糙度也有直接影响。     

C/SiC复合材料AUAG加工机理及实验研究

对C/SiC复合材料沿纤维分布方向超声磨削加工AUAG展开研究,对超声加工C/Si C复合材料的表面微观结构以及机械性能进行了评估,对表面质量随加工参数的变化而变化展开了研究。结果表明通过AUAG超声磨削加工参数的优化设计,可以得到较好的表面质量。     

SiCp/Al复合材料加工损伤及刀具优选研究进展

SiC_p/Al复合材料中增强相SiC颗粒的存在降低了该材料的加工性能,使得其切削加工时产生一系列加工损伤。本文综述了SiC_p/Al复合材料的加工缺陷类型、缺陷形成机理、缺陷控制策略和切削刀具的磨损机理与优选策略,并对今后SiC_p/Al复合材料加工损伤研究进行了展望。     

SiCp/Al复合材料界面控制与评价新方法

尝试了一种控制 Si Cp/Al复合材料界面状态与性能的新途径 ,并首次应用声发射检测技术及其信号的小波分析新方法对控制效果进行了系统地评价。结果表明 :界面控制新方法的采用 ,使 Si Cp/Al复合材料损伤、断裂过程中的 Si C颗粒拔出模式发生了转变 ,进而显著提高了材料的整体力学性能 ;小波分析特别适合于提取此类复合材料断裂所致声发射信号的深层特征 ,并可望成为反映颗粒增强金属基复合材料界面区力学行为、评价其界面性能的有效手段     

A review of friction stir joining of SiCp/Al composites

SiCp/Al composites have excellent comprehensive properties and have been widely used in aerospace, automotive industry and other fields. Due to the huge difference in performance between SiC particles and matrix alloys, traditional fusion welding methods are difficult to meet the join requirements of SiCp/Al composites. Friction stir joining (friction stir welding), as a solid phase joining process, has been proved to be a new technology with fine prospect in joining SiCp/Al composites compared with fusion welding process. Although some progress has been made in recent years, there are still full of challenges. In this paper, the research status of friction stir joining of SiCp/Al composites in recent years is expatiated, including the weldability of SiCp/Al composites, the macrostructure and the microstructure of joints, mechanical properties of joints, and tool wear and monitoring. Furthermore, the existing challenges of friction stir joining of SiCp/Al composites are summarized and the future development directions are prospected.     

C/SiC复合材料的制备及加工技术研究进展

碳纤维增强碳化硅陶瓷基(C/SiC)复合材料由于其强度高、硬度大、耐磨损,被广泛应用于工业、航空航天等领域,然而C/SiC复合材料难以被稳定地去除加工。本文综述C/SiC复合材料的常见制备方式及其材料的性能特点。概述C/SiC复合材料的传统机械加工、超声辅助加工、激光加工等加工方法,分析了各种加工方法的材料去除机理、加工精度、常见缺陷及加工过程中存在的问题。传统的机械加工需进一步优选切削刀具材料;超声辅助加工需探究超声振动的刀具与材料之间的耦合作用机制、振动作用下的材料去除机理;激光加工要进一步研究2.5维及3维C/SiC复合材料的激光加工去除机理。在这些研究的基础上进一步采用复合加工的方法,探寻C/SiC复合材料高效、精密、稳定和无损加工的可能性。     

中低体积分数SiCp / Al 在航空航天领域的应用与发展

基于中低体积分数SiCp/Al的性能特点,对比中低体积分数SiCp/Al铝合金及钛合金的力学物理性能,讨论中低体积分数SiCp/Al的性能优势,总结了中低体积分数SiCp/Al在航空航天领域应用情况及目前的发展现状,并提出未来的发展方向.     

使役条件下SiC_p/Al复合材料的建模拟实

基于有限元方法,通过Python语言开发了SiC_p/Al复合材料的参数化建模程序,利用ABAQUS图形用户界面(GUI)完成了建模过程的可视化,搭建了颗粒的大小、形状、体积含量和分布可控的快速建模拟实平台。利用此平台建立了SiC_p/Al复合材料基于微细观的代表性体积单元(RVE)有限元模型,并先后引入了颗粒的弹脆性断裂行为、基体的弹塑性断裂损伤行为和界面的拉伸-开裂行为,实现了SiC_p/Al复合材料的变形和断裂的全过程模拟。为研究使役条件下SiC_p/Al复合材料的构效关系,建立了颗粒体积含量为7%和14%的复合材料有限元模型,首先研究了拉伸过程中颗粒体积含量对复合材料变形和损伤行为的影响;然后将体积含量为7%的复合材料模拟压缩过程与拉伸过程进行对比,分析了在不同载荷条件下复合材料的变形和损伤机理。实践证明,所建立的SiC_p/Al复合材料参数化建模平台可用于颗粒增强金属基复合材料基于微细观的有限元建模,对复合材料强韧化机理分析和构效关系研究具有重要的价值。     

SiCp/Al复合材料在太阳电池阵展开机构上的应用

介绍了SiCp/Al复合材料的机械性能、热力学性能、加工性能，以及在太阳电池阵展开机构中的应用情况。分析认为采用SiCp/Al复合材料，充分发挥了其高比模量、高比强度和良好的耐磨性能，其管材、型材已达到了应用阶段。     

超声磨料对TC4钛合金电火花加工表面质量的影响

为改善TC4钛合金电火花加工表面质量,减少表面微裂纹、重熔层等表面缺陷,提出了基于电极振动的超声磨料电火花复合加工方法。在煤油工作液中混入12g/L的SiC磨料粉,进行了有无超声磨料作用的窄脉冲(脉宽小于1μs)电火花加工的表面粗糙度对比实验研究。实验结果表明:SiC磨料的超声振动作用使零件表面粗糙度Ra由0.5μm降到0.2μm左右;重熔层厚度、表面裂纹的扫描电子显微镜(SEM)照片显示,超声磨料作用使重熔层厚度减薄20～30μm,表面微裂纹得到有效控制;机理分析认为工作液高频振动及磨料对工件的冲击作用,是改善TC4钛合金电火花加工表面质量的主要原因。研究表明磨料的超声振动作用可显著改善TC4钛合金电火花加工的表面质量。     

超声振动切削金属基复合材料的刀具磨损

用实验提示超声复合加工含有硬脆强化相如SiCp、Al2O3p、SiCw等的金属基复合材料,当比例较低时,能有效地减少刀具磨损,提高刀具的耐用度;比例较高时,效果不明显.