石英纤维增强聚酰亚胺复合材料超低温铣削实验

石英纤维增强聚酰亚胺复合材料是一种非均匀的各向异性材料,采用传统铣削方法对其进行加工时存在刀具磨损严重、切削力较大、加工效率低等问题。为此本文采用超低温冷却铣削方法对石英纤维增强聚酰亚胺复合材料进行铣削实验,并与传统干铣削方式进行了对比,分析了包括加工表面形貌、粗糙度、切削力和刀具磨损等切削性能。结果表明:两种工况下,表面粗糙度随主轴转速的提高而降低,随切深的增加呈先降低后增大趋势;相对于干铣削,不同切削速度下超低温冷却铣削有效抑制了低速干铣削纤维起毛、高速干铣削黏结剂烧蚀缺陷,表面质量都得到改善,刀具耐用度得到提高。超低温冷却引起的复合材料切削力增大,纤维断屑方式的改变以及切削热的有效降低是提高加工质量的主要原因。     

高韧性芳纶纤维铣削表面质量和铣削力

文摘芳纶纤维复合材料(AFRP)在铣削过程中会产生毛边、起毛、撕裂等缺陷,严重影响材料的装配使用。为解决上述问题对刀具结构、主轴转速、进给速度进行正交实验,从铣削力、铣削表面粗糙度以及铣削表面缺陷等方面研究铣削参数和刀具结构对芳纶纤维复合材料铣削表面质量的影响规律。实验结果表明:主轴转速和进给速度对铣削表面粗糙度和铣削力有显著影响,使用鱼鳞铣刀铣削的表面粗糙度比普通四刃立铣刀的表面粗糙度降低28%,并且毛边宽度较小,铣削表面质量最好,更适合于AFRP的铣削加工。     

超声振动磨削C/SiC复合材料的试验研究

采用电镀金刚石砂轮对CVI+PIP综合工艺制备的2.5D正交编织C/SiC陶瓷基复合材料进行了轴向超声振动平面磨削加工试验.通过对超声振动磨削与普通磨削的磨削力、磨削表面三维形貌及粗糙度的分析与测量,对C/SiC复合材料的加工工艺进行了研究.结果表明,磨削过程中材料去除方式以脆性去除为主,碳纤维损伤形式以纤维拉断、剥离...     

旋转超声铣削铝合金切削力及表面粗糙度机理分析

进行了有、无旋转超声下的6061铝合金件铣削对比实验,将测力仪采集到的有、无超声时切削力数据通过MATLAB进行分析,并利用白光干涉仪观测了两种加工方式下的铣削铝件表面粗糙度。实验结果表明旋转超声铣削的切削力和表面粗糙度与普通铣削差别不大,但是旋转超声铣削铝件对抑制刀具黏着有较好的效果。     

CF/PEEK复合材料超声辅助铣削力和表面质量研究

为改善碳纤维增强聚醚醚酮复合材料（CF/PEEK）在铣削加工时所产生的毛刺、分层以及表面凹坑等缺陷，采用超声辅助铣削的加工方式分别沿0°、45°、90°、135°四种纤维方向角对CF/PEEK进行实验，并与传统铣削进行对比研究。结果表明：超声辅助铣削与传统铣削相比，切削力更小且加工质量更优。沿90°纤维方向角对试件进行超声辅助铣削，切削力、表面粗糙度和毛刺高度降幅最显著，分别降低了16.79%、28.9%和71.9%。而且在相同的加工参数下，超声辅助铣削与传统铣削相比，能够有效地改善表面凹坑、分层等表面缺陷。     

钛合金径向超声振动铣削表面粗糙度研究

为提高钛合金零件加工质量,设计了径向超声振动辅助铣削试验装置,研究了切削速度、切削深度、进给速度和超声振动幅值对钛合金零件表面粗糙度的影响规律.试验结果表明,与普通铣削相比,径向超声振动铣削后工件上的刀痕更加平整、分布更加均匀,材料去除更彻底,有效减少了由于钛合金切屑粘刀造成的表面划痕和积屑瘤等现象.在不同的切削参数下,径向超声振动铣削均可以改善钛合金零件的表面粗糙度,这一点在低速切削时更为明显,而超声振动幅值过大或过小都会影响加工质量.对加工系统的切削力进行了分析,发现超声振动辅助铣削时系统的切削力明显减小,有助于提高加工系统的稳定性,从而能够获得较好的表面质量.     

SiC晶须增强铝基复合材料超精密切削试验研究

通过聚晶金刚石刀具对SiC晶须增强铝基复合材料SiCw/LD2的超精密切削试验,并用原子力显微镜AFM对加工表面的微观形貌进行检测分析证明:SiCw/Al铝基复合材料的加工表面粗糙度值可以达到超精密级Ra0.01μm,但比切铝基体材料的表面粗糙度值大一级,且粗糙度值随着切削速度的增加、进给量的减小而减小,而吃刀量的影响不大;晶须的破坏方式对加工表面粗糙度也有直接影响。     

CFRP铣削有限元模型建立及切削力仿真分析

为探索碳纤维增强树脂基复合材料(CFRP)铣削加工过程中切削力与工艺参数之间的映射关系,建立CFRP铣削加工有限元仿真模型并对切削力进行分析。基于ABAQUS软件通过定义材料属性、材料失效模型、纤维铺层数和纤维方向建立了CFRP铣削加工二维有限元仿真模型,并对该模型进行了实验验证。基于该模型,分析了切削力与纤维方向角、铣削速度、每齿进给量和刀具前角等工艺参数之间的映射关系。仿真结果表明:纤维方向角从0°增大到90°,切削力呈现降低趋势,而纤维方向角从90°增大到180°,切削力呈现增大趋势。随着切削速度和每齿进给量的增大,切削力随之增大,而随着刀具前角增大,切削力随之减小。     

铣削参数对7055-T6铝合金耐腐蚀性的影响

文摘研究了铣削工艺参数对切削力、表面粗糙度、轮廓与形貌、自腐蚀电位和电流密度的影响。结果表明:随着切削速度的增大,切削力与表面粗糙度呈现先增大后减小再增大的变化规律;随着轴向切深的增加,切削力与表面粗糙度都呈增大的趋势;铣削后刀面对已加工表面的挤压改善了铝合金的腐蚀性能;切削转速为4 000 r/min,轴向切深为0.25 mm时,加工表面耐腐蚀性能最优;在较大的轴向切深下,已加工表面易产生微裂纹,而导致腐蚀加剧。     

高温合金高速铣削表面形貌及组织研究

为研究高温合金GH4169高速铣削表面完整性,在测量铣削过程中切削力随时间及切削参数变化规律的基础上,分析了高温合金加工表面形貌及微观组织的演化规律.结果表明:在本试验参数范围内,切削力随着切削速度的增加先升高后降低;铣削表面粗糙度随着切削速度增加而下降,随每齿进给量的增加而增加;变质层主要出现在主切削刃形成的切削表面...     

铣削加工参数对SiCp/Al复合材料表面粗糙度的影响

文摘SiC_p/Al复合材料在切削加工中存在严重的表面质量问题。本文设计单因素试验,采用硬质合金涂层刀具对SiC_p/Al复合材料进行铣削加工,研究了加工参数对表面粗糙度的影响。结果表明:表面粗糙度随切削速度的增大先增大后减小,随进给量、径向切深、轴向切深的增大而增大;使用较大的切削速度、较小的进给量和不大于4 mm的径向切深能获得较好的加工表面质量。     

纤维方向角对超低温冷却石英纤维复合材料铣削性能的影响

石英增强聚酰亚胺树脂基复合材料是一种非均匀的各向异性材料,其加工性能高度依赖于纤维铺层方向与加工进给方向所成角度,即纤维方向角。本文通过一系列不同纤维方向角的干切削和超低温冷却铣削实验,研究了纤维方向角对表面形貌、表面粗糙度、铣削力及刀具磨损的影响。结果表明:不同纤维方向角,剪应力形式不同,切削断屑形式也不同。纤维方向角为锐角时铣削表面质量均良好,但当纤维方向角增大到90°时,切削表面质量下降,切削力变化幅度增大。相同铣削时间内,在干切削工况下,刀具磨损严重,涂层脱落面积约为测量面积的70%;而在低温切削工况下,涂层未遭到严重破坏,刀具仍处于稳定磨损阶段,刀具耐用度优于干切削工况。     

Investigation on surface roughness,residual stress and fatigue property of milling in-situ TiB2/7050Al metal matrix composites

For higher efficiency and precision manufacturing, more and more attentions are focused on the surface roughness and residual stress of machined parts to obtain a good fatigue life. At present, the in-situ TiB₂/7050Al metal matrix composites are widely researched due to its attractive properties such as low density, good wear resistance and improved strength. It is of great significance to investigate the machined surface roughness, residual stress and fatigue life for higher efficiency and precision manufacturing of this new kind material. In this study, the surface roughness including two-dimensional and three-dimensional roughness, residual stress and fatigue life of milling in-situ TiB₂/7050Al metal matrix composites were analyzed. It was found from comparative investigation that the three-dimensional surface roughness would be more appropriate to represent the machined surface profile of milling particle reinforced metal matrix composites. The cutting temperature played a great role on the residual stress. However, the effect of increasing cutting force could slow down the transformation from compressive stress to tensile stress under 270 °C. An exponential relationship between three-dimensional roughness and fatigue life was established and the main fracture mechanism was brittle fracture with observation of obvious shellfish veins, river pattern veins and wave shaped veins in fracture surface.     

铣削加工透波性Si3N4陶瓷表面质量研究

为了探索透波性Si3N4陶瓷铣削中加工表面创成机理及加工工艺参数对其影响规律,对加工表面形貌和边缘破损特征,以及加工参数与切削力、表面粗糙度、边缘破损的映射关系等开展了试验研究。首先对加工表面形貌进行了分析,由于存在陶瓷粉末去除和破碎性颗粒去除两种形式,造成加工表面形貌结构一种体现为变化平缓,而另一种包含微裂纹、层状结构体等,且存在凹坑、沟槽等缺陷。其次研究了边缘破损形式及产生机理,当刀具运动到出口棱边处,刀尖应力集中处将产生微裂纹,并向工件侧面扩展,从而在加工表面和加工侧面诱导形成边缘破损。最后基于均匀设计试验,分析了工艺条件对加工性能的影响。结果表明:随着切削深度从0. 2增加到0. 5 mm和切削宽度从1增加到4 mm时,x轴切削力呈耦合增长,y轴切削力呈二次方增长;当切削深度和切削宽度分别为0. 2 mm和1 mm、进给速度为500 mm/min时,加工表面粗糙度值最小;转速为2 000 r/min、切削深度和切削宽度最小时,边缘破损幅值最小。此结果可为提高透波性Si3N4陶瓷铣削加工质量提供技术支撑。     

Effects of in-situ TiB2 particles on machinability and surface integrity in milling of TiB2/2024 and TiB2/7075 Al composites

In-situ ceramics particle reinforced aluminum matrix composites are favored in the aerospace industry due to excellent properties. However, the hard ceramic particles as the reinforcement phase bring challenges to machining. To study the effect of in-situ TiB₂ particles on machinability and surface integrity of TiB₂/2024 composite and TiB₂/7075 composite, milling experiments were performed, and compared with conventional 2024 and 7075 aluminum alloys. In-situ TiB₂ particles clustered at the grain boundaries and dispersed inside the matrix alloy grains hinder the dislocation movement of the matrix alloy. Therefore, the milling force and temperature of the composites are higher than those of the aluminum alloys due to the increase of the strength and the decrease of the plasticity. In the milling of composites, abrasive wear is the main wear form of carbide tools, due to the scratching of hard nano-TiB₂ particles. The composites containing in-situ TiB₂ particles have machining defects such as smearing, micro-scratches, micro-pits and tail on the machined surface. However, in-situ TiB₂ particles impede the plastic deformation of the composites, which greatly reduces cutting edge marks on the machined surface. Therefore, under the same milling parameters, the surface roughness of TiB₂/2024 composite and TiB₂/7075 composite is much less than that of 2024 and 7075 aluminum alloy respectively. Under the milling conditions of this experiment, the machined subsurface has no metamorphic layer, and the microhardness of the machined surface is almost the same as that of the material. Besides, compared with 2024 and 7075 aluminum alloy, machined surfaces of TiB₂/2024 composite and TiB₂/7075 composite both show tensile residual stress or low magnitude of compressive residual stress.     

Diamond wheel grinding characteristics of 3D orthogonal quartz fiber reinforced silica ceramic matrix composite

Fiber-reinforced silica ceramic matrix composites (SiO_2f/SiO₂) have gained extensive attention in recent years for its applications in aeronautics field such as radar radome and window. However, the machining properties and mechanism of the material remain unclear. The features and mechanical properties of the material itself have a significant influence on both its machining characteristics and surface integrity. Thus, a full-factor grinding experiment is conducted using a 3D orthogonal SiO_2f/SiO₂ aiming to obtain its machining characteristics. The effects of grinding parameters and tools on the grinding force, surface roughness, and material damage type are investigated using a dynamometer, Scanning Electron Microscope (SEM), and Acoustic Emission (AE) analysis. The AE frequency band is analyzed, and a semi-analytical force model is established to study the difference between a single grain and wheel grinding. It was found that the changes in surface roughness correlate with the changes in grinding force, with fiber fracture being the main reason behind the increase in grinding force. Finally, the material removal mechanism was studied based on the AE analysis. It was found that the removal mechanism is fiber fracture dominated with matrix crack and debonding, and the primary sources of energy consumption are fiber fracture and friction.     

SiCp/Al复合材料加工损伤及刀具优选研究进展

SiC_p/Al复合材料中增强相SiC颗粒的存在降低了该材料的加工性能,使得其切削加工时产生一系列加工损伤。本文综述了SiC_p/Al复合材料的加工缺陷类型、缺陷形成机理、缺陷控制策略和切削刀具的磨损机理与优选策略,并对今后SiC_p/Al复合材料加工损伤研究进行了展望。     

C/SiC复合材料螺旋铣削与钻削制孔效果对比

采用PCD刀具对C/SiC复合材料螺旋铣削与钻削制孔的制孔效果进行了对比研究。在同等加工效率条件下测量了两种制孔方法产生的切削力及切削热,并观察制孔质量。试验结果表明:螺旋铣孔产生的轴向力小于钻孔,约为钻孔的56.9%;孔壁粗糙度及孔径差均小于钻削;钻孔产生的切削热少于螺旋铣削制孔,约占螺旋铣的58.7%,但螺旋铣产生的切削热对材料及刀具的影响小。