石英玻璃的等离子体抛光技术研究现状

具有耐腐蚀、热膨胀系数低等诸多优良物理化学特性的石英玻璃在高性能光学系统中被广泛使用。要求元件达到纳米级别的表面粗糙度，而且没有损伤层和残余应力，因此精加工之后的超精密抛光工序尤为重要。本文介绍了气囊、磁流变、弹性发射、离子束等几种石英玻璃的精密抛光方法，侧重阐述了国内外等离子体的抛光技术，包括等离子体辅助化学刻蚀、等离子体喷射加工、等离子化学蒸发加工研究进展及取得的成果；且对等离子体的未来发展进行概述。     

基于等效电路模型与CDKF的锂离子电池荷电状态(SOC)估计

锂离子电池在社会生产各领域应用广泛,由于其复杂的电化学系统,状态检测难度较大,给供电保障带来不利影响.结合Thevenin等效电路与中心差分卡尔曼滤波法(CDKF),构建了一种聚合物锂离子电池的荷电状态(SOC)估计模型.MATLAB仿真验证表明,该模型能有效防止安时计数误差累积,电池SOC估计误差不超过5%.     

NiCrAl/Diatomite可磨耗封严涂层制备及性能

分别利用大气等离子喷涂技术制备了Ni/Al粘结底层、火焰喷涂技术制备了NiCrAl/Diatomite可磨耗封严涂层，研究了喷涂距离、送粉速率、火焰气体总流量、喷涂角度和氧燃比等喷涂参数对生长速率和涂层硬度的影响。结果表明，在较低的氧燃比条件下（O₂∶C₂H₂<1.6），随着喷涂距离的增大，涂层生长速率逐渐下降，硬度先保持不变后逐渐上升；当O₂∶C₂H₂>1.6时，涂层的生长速率会随着喷涂距离的增大先增大后减小，硬度随之逐渐下降。随着喷枪对基体相对移动速度的增大，涂层生长速率略微下降，硬度略有上升。气体总流量的增大使得涂层的生长速率明显上升，硬度明显下降。随着送粉量的增大，涂层生长速率明显提高，硬度随之先上升后下降。     

Crystal orientation and morphology of a lamellae in wrought titanium alloys: On the role of microstructure evolution in b processing

To obtain high-quality aviation forgings of titanium alloys, b forging is an essential processing step which must be considered throughout a production process. In this work, the effect of b forging on the crystal orientation and morphology of lamellar a was experimentally investigated in a two-phase titanium alloy. Strong dynamic recovery during b working resulted in the formation of low-angle grain boundary(LAGBb) inside b grains. The lamellar a can penetrate through the LAGBb, leading to similar intra a LAGBs on subgrain boundaries. Deformation banding occurs at high strain rates, and both diffusive and sharp boundaries of deformation bands can be observed.A continuous change of the b orientation in diffusive boundaries results in the formation of fine and disordered a lamellae without intra-lamellar boundary to hold the Burgers orientation relationship(OR). On sharp boundaries, it is prone to producing continuous grain boundary a(aGB) with a highly similar orientation along the boundaries. Meanwhile, there may exist several lower-angle boundaries within the grain boundary a for a smoother orientation change on the b grain boundary.     

RTK model and positioning performance analysis using Galileo four-frequency observations

This paper proposes a real-time kinematic (RTK) model that uses one common reference satellite for the Galileo system with four frequency observations. In the proposed model, the double-differenced (DD) pseudorange and carrier phase biases among the different frequencies are estimated as unknown parameters to recover the integer features of the DD ambiguities among the different frequencies for ambiguity resolution and precise positioning. Analysis results show that the E5a, E5b, and E5 frequencies have virtually the same performance in terms of the positioning accuracy, observation residuals, and ratio values of ambiguity resolution. However, the E1 frequency performs worse than the E5a, E5b, and E5 frequencies. The RTK results for the combination of multiple frequencies are much better than those for a single-frequency observation, the coordinates’ standard deviation is improved about 20–30%, and the ambiguity fix time is improved about 10%.     

基于未知输入观测器的四旋翼无人机故障诊断与模型参考容错控制

对四旋翼无人机（Unmanned aerial vehicle， UAV）姿态控制系统的执行器故障诊断问题进行了研究，在系统模型方面全面地考虑了模型的非线性和四旋翼无人机在飞行过程中受到外部干扰的情况。由于未知输入观测器可以将干扰、误差等作为未知输入进行处理，对干扰不敏感而对故障比较敏感，故设计了一种新的未知输入观测器进行故障诊断。同时为了保持四旋翼无人机在故障发生后的稳定性或者仍然可以按照预定轨迹运动，在得到准确的故障估计后为四旋翼无人机姿态控制系统设计了模型参考容错控制器，使其可以跟踪给定的参考模型。仿真结果证明了本文提出的故障诊断与容错控制方法的有效性。     

期望状态序列导向的深空探测器规划修复方法

Aiming at the challenges caused by the persistence, concurrency and energy consumption of probe actions, a plan repair method of deep space probe based on the expected state sequence is proposed. In this method, the expected state sequence is formed of the expected effect of the unfinished action and the expected precondition of the unexecuted action in the pre designed plan, according to the execution status of the action. The expected state sequence is an ordered set of states with mixed logic and energy, providing subgoals for plan repair and also transforming the plan repair problem into the state transition path searching problem. During the search, the plan repair strategy with energy supply priority is proposed, which separates the logic repair from energy repair to reduce the difficulty of solving the problem. And this method enables the probe to recover from plan failure autonomously. Finally, the effectiveness and rationality of the proposed method are verified through simulation by taking the Mars Orbiter as an example.     

速率模式飞轮姿态控制系统飞轮组合平稳切换方法

对速率模式飞轮姿态控制系统的能控性、稳定性和飞轮组合切换过程进行了研究，揭示了在飞轮组合切换过程中引起卫星姿态抖动的原因，提出了通过对残余角动量进行卸载并将卸载函数同时前馈到系统输入的方法，以保持卫星姿态的稳定度。从理论上证明了可引入残余角动量进行卸载，将卸载函数同时前馈到系统输入，并且不改变原系统的能控性和稳定性。给出了某卫星飞轮切换应用实例，说明了飞轮组合平稳切换方法的有效性。     

基于ESO的高超声速飞行器解耦控制

针对高超声速飞行器三通道具有强耦合的问题，提出一种基于扩张状态观测器的全通道解耦控制方法。该方法不需要根据耦合项特点设计耦合补偿模型，而是通过设计扩张状态观测器，将高超声速飞行器耦合项视为扰动，利用扩张状态观测器具有实时跟踪估计扰动的能力，将耦合项扰动估计出来。通过补偿控制来消除耦合的影响，从而完成解耦控制。进一步，通过LQR控制方法完成姿态控制系统的闭环反馈控制律设计，最终实现一种工程上实用的高超声速飞行器解耦控制方法，并通过数学仿真验证了该控制方法的正确性和有效性。