钛合金TB6铣削加工硬化实验

研究了使用涂层硬质合金刀具对钛合金TB6进行端铣加工时,铣削参数以及刀具后刀面磨损量对加工硬化（表面硬化率、硬化层深度以及硬化层硬度分布）的影响,以弄清TB6铣削硬化现象及机理.结果表明,在实验参数范围内,刀具无磨损的情况下,硬化率基本保持在107%~112%范围内,硬化层深度范围为18~36 μm;铣削速度增加时,加工硬化程度会有较为明显的降低现象,而进给量与切深对加工硬化的影响并不明显;刀具磨损对加工硬化的影响较为显著,后刀面磨损量低于0.2 mm时,硬化层深度随着磨损增加从30 μm增加至55 μm,而后刀面磨损量为0.35 mm时,硬化层深度达到了130 μm.刀具磨损后在加工表面下较浅位置出现软化区域,而且随着磨损量的增加,软化越来越明显.      

Thick galactic cosmic radiation shielding using atmospheric data

NASA is concerned with protecting astronauts from the effects of galactic cosmic radiation and has expended substantial effort in the development of computer models to predict the shielding obtained from various materials. However, these models were only developed for shields up to about 120 g/cm² in mass thickness and have predicted that shields of this mass thickness are insufficient to provide adequate protection for extended deep space flights. Consequently, effort is underway to extend the range of these models to thicker shields and experimental data is required to help confirm the resulting code. In this paper empirically obtained effective dose measurements from aircraft flights in the atmosphere are used to obtain the radiation shielding function of the Earth's atmosphere, a very thick, i.e. high mass, shield. Obtaining this result required solving an inverse problem and the method for solving it is presented. The results are shown to be in agreement with current code in the ranges where they overlap. These results are then checked and used to predict the radiation dosage under thick shields such as planetary regolith and the atmosphere of Venus.     

Analytical-HZETRN model for rapid assessment of active magnetic radiation shielding

The use of active radiation shielding designs has the potential to reduce the radiation exposure received by astronauts on deep-space missions at a significantly lower mass penalty than designs utilizing only passive shielding. Unfortunately, the determination of the radiation exposure inside these shielded environments often involves lengthy and computationally intensive Monte Carlo analysis. In order to evaluate the large trade space of design parameters associated with a magnetic radiation shield design, an analytical model was developed for the determination of flux inside a solenoid magnetic field due to the Galactic Cosmic Radiation (GCR) radiation environment. This analytical model was then coupled with NASA’s radiation transport code, HZETRN, to account for the effects of passive/structural shielding mass. The resulting model can rapidly obtain results for a given configuration and can therefore be used to analyze an entire trade space of potential variables in less time than is required for even a single Monte Carlo run. Analyzing this trade space for a solenoid magnetic shield design indicates that active shield bending powers greater than ∼15 Tm and passive/structural shielding thicknesses greater than 40 g/cm² have a limited impact on reducing dose equivalent values. Also, it is shown that higher magnetic field strengths are more effective than thicker magnetic fields at reducing dose equivalent.     

Method for the prediction of the effective dose equivalent to the crew of the International Space Station

This paper describes a methodology for assessing the pre-mission exposure of space crew aboard the International Space Station (ISS) in terms of an effective dose equivalent. In this approach, the PHITS Monte Carlo code was used to assess the particle transport of galactic cosmic radiation (GCR) and trapped radiation for solar maximum and minimum conditions through an aluminum shield thickness. From these predicted spectra, and using fluence-to-dose conversion factors, a scaling ratio of the effective dose equivalent rate to the ICRU ambient dose equivalent rate at a 10 mm depth was determined. Only contributions from secondary neutrons, protons, and alpha particles were considered in this analysis.     

基于冷热电一体化的舱外航天服生命保障系统性能

基于质子交换膜燃料电池（PEMFC）和热驱制冷,提出一种舱外航天服生命保障系统冷热电一体化方案.在分别建立金属储氢装置、PEMFC、热驱制冷系统和辐射散热器数学模型的基础上,利用冷热电一体化的热力学分析理论和方法进行了典型案例的计算,并重点分析了核心构件热驱制冷装置的参数对舱外航天服生命保障系统性能的影响.与传统的冷热电分产舱外航天服生命保障系统比较,该系统仅消耗84.6g氢气,且不需要向空间排放工质,能源利用率高达85.29%,在工质消耗与能源利用率上有较大的优势.      

电离辐照诱发面阵电荷耦合器暗信号增大试验

针对电荷耦合器件(CCD)在空间轨道环境中应用时易受到辐射损伤的影响,对面阵CCD的电离辐照损伤效应问题进行了试验研究.首先,通过开展面阵CCD60 Co γ射线电离辐照效应试验,在暗场条件下测试了面阵CCD辐照后输出信号随积分时间的变化,并拟合计算出暗信号斜率.然后,对比分析了不同偏置条件下辐照后暗信号退化的试验规律;分析了不同偏置条件下辐照后暗信号的退火恢复情况;分析了不同积分时间、不同总剂量下的暗信号不均匀性的变化规律.最后,阐述了电离辐照损伤诱发面阵CCD暗信号增大的物理机制.结果表明:面阵CCD对电离辐照损伤很敏感,在进行航天器成像系统设计时,要充分考虑CCD受电离辐照损伤带来的影响.     

我国空间电力线谐波辐射现象分析

研究了利用DEMETER卫星电磁场探测数据辨识电力线谐波辐射(PLHR,Power Line Harmonic Radiation)事件的方法,探讨了我国空间中PLHR事件的特点.通过采用时频分析和Welch功率谱估计法分析了2005-2010年6年我国空间中的全部卫星电场强度探测数据,共发现151例PLHR事件,给出了PLHR事件的统计分析和典型实例.结果表明我国空间PLHR事件的频率分布在1 000~4 500 Hz之间,多为50 Hz的奇数倍,间隔为50/100 Hz.PLHR事件与我国电网发展和变化有密切关系,与地磁活动水平无关,呈现出昼夜差异和季节差异.最后给出了影响PLHR事件探测的可能因素.     

厘米-分米波段Ⅲ型爆发的统计分析

统计分析了太阳第23周期间(2000年7月至2004年9月)在625~1500,MHz,2600~3800,MHz和5200~7600,MHz范围频谱仪观测到的Ⅲ型射电爆发. 给出了Ⅲ型爆发的分布、寿命、频率漂移率、偏振度和频率带宽. 结果显示, 频率漂移率和频率带宽的平均值随频率的增加而增大, 寿命和偏振度的平均值既不是常数也不是在宽频延伸上保持均匀不变的.最多的Ⅲ型爆发分布在625~3800,MHz范围内, 且随频率的增加而增多. 分析表明, 电子加速和能量释放地点主要是在分米波范围内, 这个频率范围的特征可能与分米波段上的磁位形有关, 并且与主耀斑地点附近磁重联区中的电子加速有关. 然而, 还有相当数量的Ⅲ型爆发发生在5200~7600,MHz范围内, 这个特征表明电子加速的地点是在一个日冕的宽范围中. 关于厘米relax-relax 分米波段Ⅲ型爆发的辐射机制最可能包含相干的等离子体辐射或电子回旋脉泽辐射过程.      

典型卫星轨道的位移损伤剂量计算与分析

位移损伤剂量是评估电子元器件在轨发生位移损伤导致性能退化的重要参数。文章首先给出了位移损伤剂量的等效原理和计算方法,即用位移损伤等效注量来表征卫星轨道带电粒子导致的位移损伤剂量;之后分别采用3种不同的太阳质子注量模型,计算了典型大椭圆轨道的位移损伤等效注量,并结合计算结果对不同模型的特点和适用性进行了分析;其后针对4种典型卫星轨道,计算了不同飞行寿命期内的位移损伤等效注量,发现不同轨道的位移损伤剂量有较大差异,并结合空间带电粒子辐射环境分布特点及卫星轨道参数等分析了差异的产生原因;最后,分析不同的太阳质子注量预估方法对位移损伤剂量计算结果的影响,总结了不同轨道、不同飞行寿命情况下卫星经受的带电粒子辐射环境的严酷程度。研究结果可为卫星内部元器件位移损伤效应防护工作提供参考。     

双S弯喷管流动特性及红外辐射特性分析

基于分区控制技术,发展了型面易控的双S弯喷管型面设计方法,用CFD数值模拟技术,对双S弯喷管的流动特性进行了数值模拟.采用信息通道界面(MPI)并行算法编写了基于离散传递法的红外辐射特性计算程序,对双S弯喷管红外辐射特性进行了计算,并与具有相同进出口面积的轴对称收缩喷管的红外辐射特性进行了对比.研究表明:双S弯喷管宽边探测面红外辐射强度低于窄边探测面红外辐射强度,最大幅度为80%;与轴对称收缩喷管相比,双S弯喷管红外辐射强度明显降低,尤其在宽边探测面的30°~40°探测方向上,比轴对称收缩喷管的红外辐射强度低大约30%.