侧载及加热方位对槽道内临界热流密度影响

为了研究侧载以及加热方位对矩形窄缝槽道内临界热流密度特性的影响,在旋转平台上进行了两相流的超重力实验.以蒸馏水为工质,通过改变质量流速、入口温度、侧载大小以及加热方位,获得了发生临界换热现象时的质量流速、实验段压降和壁温的变化趋势,考察了侧载和加热方位对临界热流密度的影响规律,并对侧载下两相流不稳定性进行了简析.实验表明:发生临界换热时,壁温迅速上升,有效加热热流开始减少,关闭加热电源后,实验段压降下降、质量流速回升较明显;侧载以及不同的加热方位对临界热流密度有明显影响;临界热流密度发生前后,蒸汽回流导致进口温度上升,增加了流动的不稳定性.      

非正交弧线齿面齿轮齿面设计及根切研究

非正交弧线齿面齿轮是以端面渐开线弧线齿圆柱齿轮为假想刀具包络展成的面齿轮。根据面齿轮啮合原理推导了非正交弧线齿面齿轮齿面方程,结合Matlab数学模型和根切理论研究了该种面齿轮的根切现象,计算出面齿轮不产生根切的最大内径,并通过Catia仿真滚齿来验证计算的准确性。该研究旨在提出一种新型非正交面齿轮,通过理论推导及仿真模拟来研究该种面齿轮的根切现象,在此基础上探究非正交弧线齿面齿轮的内径影响因素。研究结果表明:在同等参数下,当位置参数增大时,刀具渐开线截面高度和内径逐渐减小,当刀具圆弧半径增大时,内径逐渐减小,刀具渐开线截面高度逐渐增大。     

Cross-sectional deformation behavior of double-ridged rectangular tube with fillers in different stages of H-typed bending

The bent double-ridged rectangular tube (DRRT) with high forming quality is helpful to improve the microwave transmission accuracy. For reducing the cross-sectional deformation in the H-typed bending process, in addition to using rigid mandrel to support the inside of tube, ridge groove fillers are also added to restrict the deformation of ridge grooves. Because of the change of stress and strain state of bent tube in bending, rigid mandrel retracting and specially twice-springback stages, and the springback of fillers, the cross-sectional deformation of tube in each stage may be different. Therefore, based on the ABAQUS platform, the finite element models (FEM) for H-typed bending, mandrel retracting and twice-springback stages of H96 DRRT with fillers were established and validated. It is found that, for the height and width deformation of tube and spacing deformation of ridge grooves, retraction of mandrel can make the distribution of these deformations more uniform along the bending direction. The first springback can reduce these deformations significantly, which should be emphasized. But the second springback only increases them by less amount, which can be ignored. The smaller height deformation of ridge groove and filler can be neglected.     

某型飞机机翼整体油箱工艺研究

介绍了某型机机翼整体油箱的研制过程,针对总体气动、结构和使用维护等对整体油箱提出的性能要求,工程部门相应采用严格的环境措施、确保协调精度的预装配措施以及湿连接、密封装配措施等,解决了研制过程中诸多关键难题,保证了整体油箱的研制进度和产品质量,经各种试验检测和试飞考核,该整体油箱质量稳定可靠,性能良好。     

Optimum parameter matching obtained by experiments for coring drilling into lunar simulant

This paper performs a series of ground experiments (on the Earth) to obtain optimum parameter matching for a future core drill on the Moon. Three common stages, I, II, III, are recognized with respect to the cut per revolution (CPR), which is defined as the ratio between the feeding speed and the rotating speed. The optimum matching between the feeding speed and the rotating speed for drills locates at the boundary position between Stage II and Stage III, where the coring rate saturates and the weight on the bit and the driving torque are still low. Further data analysis of the ground experiments reveals that the optimum matching signifies a proportional relation between the maximum conveying rate (MCR) by the groove of the auger and its rotating speed. The kinetic analysis in an ideal condition without gravity, the friction from the auger groove and the pressure at the bit confirm a similar proportion. The correlation between the proportions needs further study to determine whether the optimum matching obtained on the ground can be directly applied to future drills on the Moon.     

多跑道内水平障碍物限制面边界确定方法

对机场多跑道系统的障碍物限制面——内水平面的边界确定方法进行了系统研究。通过将N条（N≥3）复杂构形跑道简化为2N个点集，根据国际民航组织内水平面障碍物限制面形成原理并利用多边形凹凸性几何特征，给出了内水平面边界的确定方法和计算步骤。     

Design and experimental study of a micro-groove grinding wheel with spray cooling effect

The effectiveness of grinding fluid supply has a crucial impact on grinding quality and efficiency in high speed grinding. In order to improve the cooling and lubrication, through in-depth research of self-inhaling internal cooling method and intermittent grinding mechanism, a new spray cooling method used in high speed grinding is proposed. By referring to the structure of bowl- shaped dispersion disk, the grinding wheel matrix with atomization ability is designed; through studying heat transfer of droplet collision and the influence of micro-groove on the boiling heat transfer, grinding segment with micro-groove is designed to enhance the heat flux of coolant and achieve maximum heat transfer between droplets and grinding contact zone. High-speed grinding experiments on GH4169 with the developed grinding wheel are carried out. The results show that with the micro-groove grinding wheel just 5.4% of pump outlet flow rate and 0.5% of spindle energy is needed to reduce the grinding temperature to 200℃, which means the developed grinding wheel makes cooling high efficient and low energy consuming.     

环型与线型聚能装药射流成型机理对比

环型聚能装药药型罩2侧在挤压汇聚形成射流过程中存在不对称性,不能完全套用线型聚能装药射流成型的现有理论。利用DYNA3D软件对相同剖面结构的环型、线型聚能装药射流成型过程进行数值模拟,通过比较分析得出了环型聚能装药形成杵体及射流参数的分布特性,为进一步理论研究及工程应用提供参考。     

钢球连接方式火工装置的结构强度校核

文章介绍了钢球连接方式火工装置中，钢球连接处的结构强度校核。通过经典的接触应力计算公式，结合钢球在火工装置上的具体使用情况，利用微变形理论，归纳出了火工装置上起连接承载作用的钢球连接方式新的强度校核判断法则。试验结果表明，该判据能够较为真实地反映火工装置上钢球连接方式的结构承载能力。     

抑波槽宽度对水陆两栖飞机喷溅性能影响对比试验研究

抑波槽宽度合理性直接影响抑制喷溅的效果。通过两个抑波槽宽度的单船身模型拖曳水池对比试验,比较同一状态两者喷溅包络线,分析抑波槽宽度变化对飞机喷溅性能影响,表明减小抑波槽宽度使螺旋桨处喷溅高度增加19%以上,使襟翼处喷溅高度降低54%。