Si和Ti对Nb-6Hf-4Zr-2B合金组织和室温力学性能的影响

 为了寻求Nb合金的强度和塑性的平衡,设计了以Nb基固溶体Nbss为主导相的Nb-xSi-6Hf-4Zr-2B-yTi(x=4,8;y=10,30;原子分数)合金,研究了Si和Ti对合金组织和室温力学性能的影响。结果表明,合金由Nbss、Nb3Si和Nb5Si3等3相组成。4Si-(10,30)Ti合金铸态组织是Nb枝晶和分布在枝晶间的硅化物(Nb3Si和Nb5Si3),8Si-(10,30)Ti合金Nb枝晶间分布的是Nb/硅化物(Nb5Si3)的共晶和Nb3Si,随着Si和Ti含量的增加,硅化物体积分数增加。1 600 ℃退火50 h可使部分Nb3Si共析分解,改变合金的组织形貌和各相的体积分数。随着Si和Ti含量的增加,合金的硬度和强度增加,但塑性和韧性降低。Nb枝晶的失效方式为解理断裂,而硅化物为脆性断裂。     

Microstructure evolution of a hypereutectic Nb–Ti–Si–Cr–Al–Hf alloy processed by directional solidification

In this work, the Nb–14Si–24Ti–10Cr–2Al–2Hf–0.1Y alloy(at.%) was processed by the liquid–metal-cooled directional solidification(DS) at 1750 C with withdrawal rates of 1.2, 6,18 mm/min and post heat treatment(HT) at 1450 C for 10 h. The microstructures of the directionally solidified and heat treated samples were investigated. The results show that the microstructure of directionally solidified alloy mainly consists of petaloid Nbss+ Nb5Si3eutectics and Ti-rich Nbss+ Nb5Si3+ Cr2Nb eutectics. With the increase of withdrawal rate, the primary Nb5Si3is eliminated, Nbss+ Nb5Si3eutectic cells turn round and connected with the microstructure refinement and Nbss+ Nb5Si3+ Cr2Nb eutectics turn to a river-like morphology. After heat treatment,Nbss+ Nb5Si3+ Cr2Nb eutectics disappeared and petaloid Nbss+ Nb5Si3eutectics turn to a specific fiber-mesh structure gradually, which is promoted by higher withdrawal rates. Furthermore,both the volume fraction of Cr2Nb and the content of Cr in Nbssof Nbss+ Nb5Si3eutectics change regularly with the increase of withdrawal rate and heat treatment at 1450 C for 10 h.     

Nb-Si-Mo三元系合金相图

 Nb/Nb5Si3原位复合材料是一种有望替代镍基超合金用做飞机发动机叶片的新一代超高温结构材料。采用非自耗电弧熔炼技术制备出不同成分的Nb/Nb5Si3原位复合材料,利用X射线衍射仪、扫描电镜和能谱仪对Nb-Si-Mo三元系合金的相组成和微观组织进行研究。结果表明：Nb-Si-Mo三元系部分液相面投影图（<37.5 at% Si）含有4个初生相区,其立体相图中存在2个液固四相平衡反应和1个固态四相平衡反应。在2个液固四相平衡反应面之间存在一个三相共晶平衡棱柱,成分位于该棱柱内的合金会通过L→Nbss+β-Nb5Si3反应凝固生成Nbss/β-Nb5Si3片层共晶。     

冷坩埚定向凝固TiAl基合金高温持久性能研究

采用电磁冷坩埚定向凝固技术制备了成分为Ti-47A1-2Cr-2Nb的合金铸锭,定向凝固后的显微组织为α2+γ全片层结构.在0.4～1.2mm/min的抽拉速率范围内,随着抽拉速率的增加,片层间距减小,柱状晶与生长方向的夹角增大.随着温度升高,合金的拉伸强度有所下降,但由于细化片层界面对切变应力变形的阻碍作用,合金的高温拉伸强度会随着抽拉速率的增加而提高.通过对抽拉速率为1.0mm/min试样的拉伸强度与温度的拟合,得到了拉伸强度和温度之间的函数关系.随着抽拉速率的增加,Ti-47A1-2Cr-2Nb合金的持久寿命明显升高,对于抽拉速率为1.2mm/min试样的持久性能测试表明,其持久寿命最长,达到了48h.持久试样的断口形貌表明,其断裂的主要方式是伴随着少量延性断裂的脆性解理断裂.最后根据时间-温度模型,分别采用Larson-Miller和Manson-Haferd参数法建立了定向凝固Ti-47Al-2Cr-2Nb合金的持久强度预测函数模型,预测的理论值与试验结果吻合度较高.     

抽拉速率对定向凝固DZ4125合金温度场及晶粒竞争生长的影响

为探究定向凝固DZ4125柱晶高温合金中温度场分布情况，并研究不同抽拉速率对温度梯度及糊状区变化的影响规律，利用ProCAST软件对抽拉速率分别为3、5、7 mm/min的定向凝固过程进行模拟。结果表明：当试棒位于保温区时，等温线呈外侧低内侧高的倾斜分布，当试棒位于冷却区时，等温线呈外侧高内侧低的倾斜分布；随着抽拉速率的增加，温度梯度逐渐减小；糊状区形状取决于抽拉速率和距水冷盘的距离，当抽拉速率为5 mm/min时，凝固前沿水平状保持的时间最长；在此基础上，对定向凝固试棒进行精铸实验，并研究3mm/min和7 mm/min下试棒液相线形状与晶粒结构之间的关系，发现液相线呈凹形和凸形时，晶粒分别向试棒中心和表面方向生长，水平的液相线能促进晶粒沿试棒轴线方向生长。     

Microstructure, Mechanical Properties and Oxidation Resistance of Nb-22Ti-14Si-2Hf-2Al-xCr Alloys

Nb-22Ti-14Si-2Hf-2Al-xCr (x=2, 6, 10, 14, 17 at%) alloys are prepared by arc-melting under argon atmosphere. Microstructural characteristics, mechanical properties and oxidation resistance of the arc-melted alloys are investigated. At 2 at% Cr content, the microstructure is composed of Nbss, Nb3Si and a small quantity of Nb5Si3, when the Cr contents increase, Nb3Si disappears. For the high Cr content (x ≥ 10 at%) alloys, besides the Nbss and Nb5Si3, Cr2Nb is also detected. With the increase of Cr content, the volume fractions of Cr2Nb and Nb5Si3 increase, while that of Nbss increases firstly and then begins to degrade when the Cr content is higher than 6 at%. For the alloy with 2 at% Cr, the room temperature fracture toughness is about 14.5 MPa·m1/2, but badly decreases to about 8.5 MPa·m1/2, when the Cr contents increase. Vickers hardness of Nbss tends to increase linearly from about 400 to 500, while that of silicides is not sensitive to Cr contents, about 950. The appearance of Cr2Nb phase significantly improves the high temperature oxidation resistance of the alloys with high Cr contents. The isothermal oxidation tests show that the oxidation kinetics of the alloys with various Cr contents follows parabolic oxidation kinetics.     

Cr对Nb-16Si-22Ti-2Al-2Hf合金显微组织与高低温力学性能的影响

 以Nb-16Si-22Ti-2Al-2Hf成分为基础,分别添加了2%和17%(原子分数,后同)的Cr元素替代Nb(分别称2Cr和17Cr合金),研究了Cr含量对Nb-16Si-22Ti-2Al-2Hf合金相组成、显微组织形貌、室温断裂韧性和高温强度的影响,分析了高低温失效机制。结果表明,铸态和1 375 ℃×100 h热处理后2Cr合金由Nbss和Nb₅Si₃两相组成;当Cr含量为17%时,出现了具有C15结构的Laves Cr₂Nb相,合金由Nbss、Nb₅Si₃和Cr₂Nb三相组成,热处理后在Nb₅Si₃中还析出了球状Cr₂Nb相。随着Cr含量由2%提高到17%,热处理合金的室温断裂韧性K_Q由14.32 MPa·m^1/2下降到10.30 MPa·m^1/2。合金强度与Cr含量的关系受温度影响,随Cr含量提高,室温和1 150 ℃时合金的硬度或强度增高,而1 250 ℃和1 350 ℃时合金强度降低。如1 150 ℃时2Cr和17Cr合金的屈服强度σ_0.2分别为349 MPa和387 MPa;1 350 ℃时分别为306 MPa和74 MPa。     

Hf对Nb15W5Si2B合金室温和高温力学性能的影响

 为了寻求Nb-Si基合金高温强度和室温塑性之间的平衡,设计了以Nb基固溶体相Nb-SS占主导的Nb15W5Si2BxHf(x= 0,5,10,15,原子百分数）合金,研究了Hf元素对Nb15W5Si2B合金的组织、室温和高温压缩性能以及高温蠕变性能的影响。结果表明,Nb15W5Si2B合金由Nb-SS和Nb5Si3两相组成,Nb5Si3相呈网状分布;Hf的加入不改变相组成,但Nb5Si3相由网状分布逐步变成不连续小岛状分布,而且体积分数减少。Hf同时提高Nb15W5Si2B合金的高温静强度和室温塑性,但对Nb15W5Si2B高温压缩蠕变性能不利。最后讨论了Hf对Nb15W5Si2B合金强化与塑性化机理。     

快速凝固/粉末冶金Al-20Si-7.5Ni-3Cu-1Mg-0.25Fe合金的显微组织与力学性能

采用快速凝固/粉末冶金工艺制备Al-20Si-7.5Ni-3Cu-1Mg-0.25Fe合金挤压棒材,通过OM,SEM,TEM,XRD和拉伸试验等手段研究挤压态和T6态合金的显微组织及力学性能。结果表明:挤压态和T6态合金的主要组成相均为α(Al),β(Si),Al3Ni,Al3Ni2,Al7Cu4Ni和Al4Cu2Mg8Si7。挤压态合金中块状Si相平均尺寸约为2.4μm,且带有明显尖角;T6热处理后,块状Si相发生粗化和球化现象,粗化后其平均尺寸约为3.2μm。T6态合金的室温抗拉强度和屈服强度分别为490MPa和415MPa,硬度达到91.3HRB。挤压态和T6态合金的拉伸断口平整,均属脆性断裂,且断口出现由Si相破裂后形成的小平面。     

定向凝固Ni-44Ti-5Al-2Nb-1Mo合金的组织特征

采用液态金属冷却定向凝固方法制备了Ni-44Ti-5 Al-2 Nb-1 Mo(原子分数,％)合金,分析了加热温度为1 550℃,抽拉速率为0.3、1.2、3.0、6.0、18.0 mm/min时的定向凝固组织特征.结果表明,定向凝固没有改变合金的相组成,但改变了组成相的形态.定向凝固组织均由初生的NiTi相与晶间析出...     

跨流域高超声速绕流Boltzmann模型方程并行算法

通过对Boltzmann方程碰撞积分进行模型化处理,提出了统一描述各流域复杂高超声速流动输运现象的气体分子速度分布函数控制方程,使用离散速度坐标法对分布函数方程所依赖的速度空间离散降维,构造出直接求解分子速度分布函数的气体动理论耦合迭代数值格式,研制了复杂飞行器高超声速绕流气动热力学计算模型。基于对气体动理论数值计算方法内在并行性、变量依赖关系、数据通信与并行可扩展性的分析研究,使用区域分解并行化方法提出了新型的气体动理论数值算法并行方案;研究了数据的并行分布与并行执行特征,开展了大规模的并行化程序设计,构造了可稳定运行于成千上万CPU的高性能并行算法,用以模拟各流域复杂飞行器的高超声速绕流问题。以稀薄流到连续流环境下不同Knudsen数、不同马赫数的可重复使用类球锥卫星体及翼身组合复杂飞行器等气动力、热绕流问题为研究对象展开大规模并行计算,并进行算法验证,所得计算结果与理论分析、直接模拟蒙特卡罗方法(DSMC)的模拟值及有关实验数据吻合较好,揭示了飞行器跨流域高超声速下的复杂流动机理与变化规律,提供了一条能够可靠模拟高超声速飞行器跨流域气动力及热问题的统一的算法应用研究途径。     

μ理论在电液负载模拟器中的应用

 研究μ理论在电液负载模拟器中的应用，提出电液负载模拟器的鲁棒控制策略。电液负载模拟器是一个复杂的机-电-液复合系统，且是一个强耦合、时变受控对象。综合考虑参数变化、模型变动和干扰等不确定性的影响，利用μ综合控制理论设计电液负载模拟器的鲁棒力控制器，并通过μ分析使用鲁棒力控制器时系统的鲁棒稳定性和鲁棒性能。给出使用鲁棒力控制器和经典力控制器时的实验结果，实验结果表明所设计鲁棒力控制器的有效性和优越性。     

基于圆型限制性三体问题模型的行星卫星逃逸能量研究

 基于由飞行器、行星及其卫星组成圆型限制性三体问题模型，通过庞加莱映射的方法，研究了飞行器从行星卫星附近逃逸的问题。在Jacobi常数确定的前提下，通过逆向积分，飞行器从L1或L2点附近返回近月点，得到近月点速度出发速度。研究结果表明绕飞L1点和L2点逃逸行星卫星需要的最低能量是不同的，从月球表面逃逸所需的速度脉冲分别比开普勒算法节省46.5m/s和42.3m/s，且均小于Villac等人在Hill模型下得到38.9m/s，从而改进了Villac等人的相关工作，同时也给出了从太阳系主要行星卫星表面逃逸所需的最小能量。     

Model Development and Adaptive Imbalance Vibration Control of Magnetic Suspended System

对星载磁悬浮单框架控制力矩陀螺,建立其转子的平动与转动的动力学方程。所建模型反映了转子的动、静不平衡特性,以及转子运动与框架、星体运动的耦合关系。模型是主动磁悬浮控制与动框架效应分析的基础。对动、静不平衡量未知的转子,设计了自适应对中控制器。在分散PD、比例交叉反馈控制器与高低通滤波器的基础上,通过动、静不平衡量的辨识与补偿控制,使转子绕其惯量主轴旋转,衰减角动量交换执行机构高速转子因不平衡而对基座产生的干扰力,消除星上主要颤振源,达到降低卫星姿态抖动的目的。     

Love Waves in Layered Graded Composite Structures with Imperfectly Bonded Interface

Theoretical analysis and numerical calculations of Love wave propagation in layered graded composites with imperfectly bonded interface are described in this paper. On the basis of WKB method, the approximate analytic solutions for Love waves are obtained. By the interface shear spring model, the dispersion relations for Love waves in layered graded composite structures with rigid, slip, and imperfectly bonded interfaces are given, and the effects of the interface conditions on the phase velocities of Love waves in SiC/Al lay- ered graded composites are discussed. Numerical analysis shows that the phase velocity decreases when the defined flexibility parameter is greater. For the general imperfectly bonded interface, the phase velocity changes in the range of the velocities for the rigid and slip interface conditions.     

Compression Creep Behavior of High Volume Fraction of SiC Particles Reinforced Al Composite Fabricated by Pressureless Infiltration

The compression creep deformation of the high volume fraction of SiC particles reinforced Al-Mg-Si composite fabricated by pressure-less infiltration was investigated. The experimental results show that the creep stress exponents are very high at temperatures of 673 K, 723 K and 773 K, and if taking the threshold stress into account, the true stress exponent of minimum creep strain rate is still approximately 5, although the volume fraction of reinforcements is very high. The creep strain rate in the high volume fraction rein- forced aluminum alloy matrix composites is controlled by matrix lattice diffusion. It is found that the creep-strengthening effect of high volume fraction of silicon carbide particles is significant, although the particles do not form effective obstacles to dislocation motion.     

Experimental Investigation on Performance of Pulse Detonation Rocket Engine Model

The PDRE test model used in these experiments utilized kerosene as the fuel, oxygen as oxidizer, and nitrogen as purge gas. The solenoid valves were employed to control intermittent supplies of kerosene, oxygen and purge gas. PDRE test model was 50 mm in inner diameter by 1.2 m long. The DDT （deflagration to detonation transition） enhancement device Shchelkin spiral was used in the test model. The effects of detonation frequency on its time-averaged thrust and specific impulse were experimentally investigated. The obtained results showes that the time-averaged thrust of PDRE test model was approximately proportional to the detonation frequency. For the detonation frequency 20 Hz, the time-averaged thrust was around 107 N, and the specific impulse was around 125 s. The nozzle experiments were conducted using PDRE test model with three traditional nozzles. The experimental results obtained demonstrated that all of those nozzles could augment the thrust and specific impulse. Among those three nozzles, the convergent nozzle had the largest increased augmentation, which was approximately 18%, under the specific condition of the experiment.     

高超声速飞行器高温流场数值模拟面临的问题

随着高超声速飞行器目标光辐射和电磁散射特性研究的发展和深入,高温流场特性日益引起人们的关注。由于高温流场特性研究中涉及到非常多的复杂气动现象,如气动加热、烧蚀、辐射、燃烧、化学反应以及湍流等,因此其数值模拟面临着诸多挑战。这里基于连续流计算流体力学(CFD)技术和稀薄气体蒙特卡罗直接仿真(DSMC)方法,从化学物理模型建模、方法稳定性与数值求解效率出发,分析了高超声速飞行器外部绕流、尾迹和发动机喷焰三方面的流场特性数值模拟在不同弹道、热防护手段和飞行流域环境下所面临的问题。在此基础上提出了数值求解技术和化学物理模型建模今后需要发展的方向,为有效提高高超声速高温流场特性数值模拟效率、增加流场特性预测精度提供了指导,从而为研究流场对高超声速飞行器目标光辐射和电磁散射特性影响提供有效的基础数据。     

Adaptive Control of Helicopter Ground Resonance with Magnetorheological Damper

The methodology for adaptive control of helicopter ground resonance with magnetorheological （MR） damper is presented. The adaptive inverse control method is used to control the output damping force of MR damper and the range of the damping force is given. Through the adaptive inverse control, the damping force of MR damper is fit to a desired damping force. With the background of applying MR damper to control of helicopter ground resonance, a model of loss force and an adaptive arithmetic for stabilization of the coupled rotor/fuselage system are presented. The simulation shows that the controller presented in this paper can stabilize the rotor/fuselage coupling system quickly and control the helicopter ground resonance effectively.     

带放气槽的定几何二元倒置“X”型混压式超音速进气道实验研究(英文)

针对一种带放气槽的定几何二元倒置"X"型混压式超音速进气道进行了风洞吹风实验。结果表明:随着来流马赫数的增加,进气道总压恢复系数不断减小,流量系数却先增加,在设计点达到最大值后减小;当攻角变化时,两侧进气道变化各异,在小攻角α≤60时,随着攻角的增加,迎背风两侧进气道的总压恢复系数均有所下降,但背风侧进气道总压恢复系数高于迎风侧进气道,在流量系数方面,背风侧进气道先增加后减小,而迎风侧进气道一直保持缓慢下降,但两侧总的流量保持变化不大,在大攻角(α=60-90)状态下,背风侧进气道总压恢复系数和流量系数均下降剧烈,而迎风侧进气道总压恢复系数下降但流量系数却有所上升;同时,通过与不带放气槽进气道的速度特性以及反压特性对比发现,放气槽的存在不但增加了进气道的稳定工作范围,而且对进气道在高马赫数下性能的提高也大有裨益。本文为倒置"X"型进气道的设计、改进提供了实验依据。