Maximum likelihood angle extractor for two closely spaced targets

In a scenario of closely spaced targets special attention has to be paid to radar signal processing. We present an advanced processing technique, which uses the maximum likelihood (ML) criterion to extract from a monopulse radar separate angle measurements for unresolved targets. This processing results in a significant improvement, in terms of measurement error standard deviations, over angle estimators using the monopulse ratio. Algorithms are developed for Swerling I as well as Swerling III models of radar cross section (RCS) fluctuations. The accuracy of the results is compared with the Cramer Rao lower bound (CRLB) and also to the monopulse ratio technique. A novel technique to detect the presence of two unresolved targets is also discussed. The performance of the ML estimator was evaluated in a benchmark scenario of closely spaced targets - closer than half power beamwidth of a monopulse radar. The interacting multiple model probabilistic data association (IMMPDA) track estimator was used in conjunction with the ML angle extractor     

Correlation between horizontal and vertical monopulse measurements

Many radar systems use the monopulse ratio to extract angle of arrival (AOA) measurements in both azimuth and elevation angles. The accuracies of each such measurement are reasonably well known: each measurement is, conditioned on the sum-signal return, Gaussian-distributed with calculable bias (relative to the true AOA), and variance. However, we note that the two monopulse ratios are functions of basic radar measurements that are not entirely independent, specifically in that the sum signal is common to both. The effect of this is that the monopulse ratios are dependent, and a simple explicit expression is given for their correlation; this is of considerable interest when the measurements are supplied to a tracking algorithm that requires a measurement covariance matrix. The system performance improvement when this is taken into account is quantified: while it makes little difference for a tracking radar with small pointing errors, there are more substantial gains when a target is allowed to stray within the beam, as with a rotating (track-while-scan) radar or when a single radar dwell interrogates two or more targets at different ranges. But in any case, the correct covariance expression is so simple that there is little reason not to use it. We additionally derive the Cramer-Rao lower bound (CRLB) on joint azimuth/elevation angle estimation and discover that it differs only slightly from the covariance matrix corresponding to the individual monopulse ratios. Hence, using the individual monopulse ratios and their simple joint accuracy expression is an adequate and quick approximation of the optimal maximum likelihood procedure for single resolved targets.     

Radar measurement extraction in the presence of sea-surface multipath

In the presence of sea-surface multipath monopulse radar signals from a low elevation target have three alternative paths in addition to the direct (radar-to-target) path due to reflections from the sea surface. The specular reflection causes significant signal fading. The diffuse reflection causes an approximately constant bias to the in-phase component of the monopulse ratio, which is the standard extractor of the direction of arrival (DOA) in the monopulse processing. The diffuse reflection also causes higher standard deviation to the in-phase component of the monopulse ratio. We propose a maximum likelihood (ML) angle extraction technique for low elevation targets of known average signal strength having a Rayleigh fluctuation. The results show that this method reduces the error of the estimated angle compared with the conventional monopulse ratio estimator. Subsequently, the ML angle extractor is modified for the unknown average signal strength case. This modified angle extractor has only a small performance degradation compared with the known average signal strength case, but it performs much better than the monopulse ratio based estimator. An algorithm to calculate the accuracy of the estimated angle (or height) is also presented. This angle extractor reduces the root-mean-square error (RMSE) by more than 50% in the signal processing stage when used in a low flying target tracking scenario. The same algorithm can be used to track sea skimmers.     

Unresolved Rayleigh target detection using monopulse measurements

When the returns from two or more targets interfere (i.e., the signals are not resolved in the frequency or time domains) in a monopulse radar system, the direction-of-arrival (DOA) estimate indicated by the monopulse ratio can wander far beyond the angular separation of the targets. Generalized maximum likelihood (GML) detection of the presence of unresolved Rayleigh targets is developed with probability density functions (pdfs) conditioned on the measured amplitude of the target echoes. The Neyman-Pearson detection algorithm uses both the in-phase and quadrature portions of the monopulse ratio and requires no a priori knowledge of the signal-to-noise ratio (SNR) or DOA of either target. Receiver operating characteristic (ROC) curves are given along with simulation results that illustrate the performance and application of the algorithm     

Multiple radar targets estimation by exploiting induced amplitude modulation

This work deals with the problem of estimating complex amplitudes, Doppler frequencies, and directions of arrival (DOA) of multiple targets present in the same range-azimuth resolution cell of a surveillance radar. The maximum likelihood (ML) and the asymptotic (large sample size) ML (AML) estimators are derived. To reduce the computational complexity of the maximization of the nonlinear two-dimensional criterion function of the AML estimator, we propose a computationally efficient algorithm based on the RELAXation method. It allows decoupling the problem of jointly estimating the parameters of the signal components into a sequence of simpler problems, where the parameters of each component are separately and iteratively estimated. The proposed method overcomes the resolution limitation of the classical monopulse technique and resolves multiple targets exhibiting an arbitrarily small difference in azimuth as long as their Doppler frequencies differ at least by the inverse of the number of integrated pulses, provided that enough signal-to-noise ratio (SNR) per pulse is available. The performance of the proposed AML-RELAX estimator is numerically investigated through Monte Carlo simulation and Cramer-Rao lower bound (CRLB) calculation.     

Tracker and signal processing for the benchmark problem with unresolved targets

Radar signal processing is particularly important in tracking closely spaced targets and targets in the presence of sea-surface-induced multipath. Closely spaced targets can produce unresolved measurements when they occupy the same range cell of the radar. These issues are the salient features of the benchmark problem for tracking unresolved targets combined with radar management, for which this paper presents the only complete solution to date. In this paper a modified version of a recently developed maximum likelihood (ML) angle estimator, which can produce two measurements from a single (unresolved) detection, is presented. A modified generalized likelihood ratio test (GLRT) is also described to detect the presence of two unresolved targets. Sea-surface-induced multipath can produce a severe bias in the elevation angle measurement when the conventional monopulse ratio angle extractor method is used. A modified version of a recently developed ML angle extractor, which produces nearly unbiased elevation angle measurements and significantly improves the track accuracy, is presented. Efficient radar resource allocation algorithms for two closely spaced targets and targets flying close to the sea surface are also presented. Finally, the IMMPDAF (interacting multiple model estimator with probabilistic data association filter modules) is used to track these targets. It is found that a two-model IMMPDAF performs better than the three-model version used in the previous benchmark. Also, the IMMPDAF with a coordinated turn model works better than the one using a Wiener process acceleration model. The signal processing and tracking algorithms presented here, operating in a feedback manner, form a comprehensive solution to the most realistic tracking and radar management problem to date.     

Complex Indicated Angles Applied to Unresolved Radar Targets and Multipath

The off-axis angle indicated by a conventional monopulse radar is only the real part of a "complex indicated angle." The presence of unresolved targets or multipath distorts the real part (causing an erroneous angle indication) and also produces an imaginary part, which can easily be measured by processing the normally unused quadrature-phase component of the difference signal. Under certain conditions the angles, amplitude ratio, and relative phase of two unresolved targets can theoretically be determined by meas urements of the complex indicated angle on two pulses separated by a short interval. In the special case of multipath, known relationships between the unresolved target and image theoretically permit determination of target elevation with a single pulse.     

比相单脉冲雷达测角与角闪烁研究

比相单脉冲雷达采用和差通道接收信号比相的方法测角。一般认为,雷达事实上并不是在测量目标的方向,而是在测量目标的角闪烁方向。从特殊的两点目标出发,分析了单点目标和复杂目标下比相单脉冲雷达和差通道方式测角的原理与内在异同,探讨了比相单脉冲雷达测角与角闪烁的关系,提出有关雷达测角的新的观点。     

Detection of Target Multiplicity Using Monopulse Quadrature Angle

The feasibility of using the indicated quadrature angle of arrival of a monopulse radar to discriminate a single target from multiple targets, separated in angle within a radar resolution cell, is investigated. The analysis is performed for steady (fixed) and Rayleigh fluctuating targets which cover a broad range of target characteristics. In both cases, the interfering signals due to noise and clutter in the sum and difference monopulse channels are assumed to be independent, zero-mean Gaussian processes. Detection and false alarm probabilities are evaluated analytically and the receiver operating characteristics are obtained for both fixed and fluctuating target cases. It is shown that multiple targets can be discriminated from a single target condition by integrating the indicated monopulse quadrature angle of arrival from several independent pulses. It is also shown that the probability of detecting multiple targets increases as the fluctuation in the target radar cross section decreases, approaching the fixed amplitude case in the limit.     

Detecting the Presence of Target Multiplicity

A method is discussed for detecting the presence of multiple targets in the radar antenna beam. It is assumed that the targets are unresolvable in range, Doppler, and angle using conventional monopulse resolution techniques. The basic approach taken is a generalization of the "quadrature" method, with significantly enhanced performance in the case when multiple pulses are integrated into a single solution. Detection and false alarm probabilities are derived analytically and the receiver operating characteristics are graphed. This study was performed for application to angle processing in a frequency agile automatic tracking radar, but the underlying concept is general and has applications outside this area.     

The Effect of Jamming on Monopulse Accuracy

An expression is applied for the probability density function (pdf) of the monopulse ratio when skin echoes from a passive target are contaminated by interference from a jammer. The analysis is valid for arbitrary signal-to-jam ratio and arbitrary locations of the target and jammer in the beam. For an on-axis skin target and a stand-off jammer at an off-axis location, the "pulling" effect of the jammer and the accuracy of the angle estimate are compared with the approximations currently employed in radar performance analysis. The pdf of the monopulse ratio for large and for small signal-to-jam ratios is presented, showing that the pdf is bimodal at small signal-to-jam ratio.     

Difference beam aided target detection in monopulse radar

The classical detection step in a monopulse radar system is based on the sum beam only,the performance of which is not optimal when target is not at the beam center. Target detection aided by the difference beam can improve the performance at this case. However, the existing difference beam aided target detectors have the problem of performance deterioration at the beam center, which has limited their application in real systems. To solve this problem, two detectors are proposed in this paper. Assuming the monopulse ratio is known, a generalized likelihood ratio test(GLRT) detector is derived, which can be used when targeting information on target direction is available. A practical dual-stage detector is proposed for the case that the monopulse ratio is unknown. Simulation results show that performances of the proposed detectors are superior to that of the classical detector.     

Beam Shape Loss and Surveillance Optimization for Pencil Beam Arrays

A radar in its surveillance mode requires the programming of the radar beam in fixed angular increments throughout the surveillance volume. Though radar coverage of the volume is complete, returns from possible targets differing only in angular position generally have unequal signal strengths. This is due to both beam shape and multiple beam coverage. The resulting nonuniformity in signal strength results in a loss factor termed beam shape loss (BSL). This correspondence contains the results of a valid computational procedure for determining this loss factor for the case of an electronically steerable array in a search mode. Results consist of curves showing BSL for a wide range of system parameters and for various target types. In addition, it is shown how optimum search beam locations can be determined from the BSL computations.     

Monopulse DOA estimation of two unresolved Rayleigh targets

This paper provides for new approaches to the processing of unresolved measurements as two direction-of-arrival (DOA) measurements for tracking closely spaced targets rather than the conventional single DOA measurement of the centroid. The measurements of the two-closely spaced targets are merged when the target echoes are not resolved in angle, range, or radial velocity (i.e., Doppler processing). The conditional Cramer Rao lower bound (CRLB) is developed for the DOA estimation of two unresolved Rayleigh targets using a standard monopulse radar. Then the modified CRLB is used to give insight into the boresight pointing for monopulse DOA estimation of two unresolved targets. Monopulse processing is considered for DOA estimation of two unresolved Rayleigh targets with known or estimated relative radar cross section (RCS). The performance of the DOA estimator is studied via Monte Carlo simulations and compared with the modified CRLB     

反向交叉眼对单脉冲雷达干扰效果分析及仿真验证

交叉眼干扰被认为是对单脉冲雷达干扰最有效的方式之一。基于雷达方程建立了隔离平台回波下的两点源反向交叉眼干扰模型，推导了交叉眼干扰欺骗角一般性公式，研究了干扰机发射天线间距、干扰平台旋转角和干扰机相对雷达之间距离等参数变化对角度欺骗效果的影响，并依据单脉冲雷达接收机获取角度的信息处理流程，建立了单脉冲雷达接收机仿真模型，对交叉眼数学模型的正确性和局限性进行了分析。研究结果表明：单脉冲雷达越靠近两点源交叉眼干扰机中心线、干扰机两发射天线间距越大、与干扰机距离越近时，角度欺骗效果越好；单脉冲雷达的欺骗角度随着与干扰机距离的接近呈指数式增大；数学模型和仿真模型计算的单脉冲雷达角度误差最大值随干扰机天线与雷达天线中心连线的夹角的增大呈指数化增长。研究可为交叉眼干扰工程设计作参考。     

单脉冲跟踪雷达多目标检测算法性能分析

对2种检测单脉冲雷达主波束内是否存在2个不可区分目标的算法进行了推广,将其应用到波束内可能存在N个不可区分的目标,并仿真了波束内存在3个目标时的检测性能。仿真表明,在总信噪比相同时,3个目标的检测概率不一定大于2个目标的检测概率,处于方位向上间距最大的2个目标的信噪比对整个检测概率影响较大。     

Bias compensation and tracking with monopulse radars in the presence of multi path

The problem of tracking targets in the presence of reflections from sea or ground is addressed. Both types of reflections (specular and diffuse) are considered. Specular reflection causes large peak errors followed by an approximately constant bias in the monopulse ratio, while diffuse reflection has random variations which on the average generate a bias in the monopulse ratio. Expressions for the average error (bias) in the monopulse ratio due to specular and diffuse reflections and the corresponding variance in the presence of noise in the radar channels are derived. A maximum maneuver-based filter and a multiple model estimator are used for tracking. Simulation results for five scenarios, typical of sea skimmers, with Swerling III fluctuating radar cross sections (RCSs) indicate the significance and efficiency of the technique developed in this paper-a 65% reduction of the rms error in the target height estimate.     

Statistical description of monopulse parameters for trackingRayleigh targets

The conditional probability density function (pdf) is developed for each monopulse measurement of a Rayleigh target by conditioning the pdf of the complex monopulse ratio on the measured amplitude of the sum signal. The conditional pdf is used to develop the conditional Cramer-Rao Lower Bound (CRLB) for any unbiased estimator of the direction-of-arrival (DOA). Conditional maximum likelihood (CML) and conditional method of moments (CMM) estimators of the DOA are developed along with estimates of the variances associated with the monopulse ratio and DOA estimate. Using simulation results, the performances of the CML and CMM estimators of the DOA are compared with the performance of standard monopulse ratio and the performances of the variance estimators are also studied     

单脉冲成像算法性能分析

单脉冲技术通过比较单个脉冲多路回波信号的信息实现对目标角度位置的精确测量,广泛运用于跟踪雷达中。在雷达成像中引入单脉冲技术可以显著提高前视这一合成孔径雷达(SAR)与多普勒波束锐化(DBS)成像盲区雷达图像的清晰度。本文着重对单脉冲成像算法的成像效果分析方法进行研究。从单脉冲和差比的概率密度函数出发,提出了目标图像位置失真、分辨率以及图像信噪比3个对图像质量进行衡量的指标。分析了决定这3个指标的系统及外部环境参数,并给出了相应的计算方法。最终通过数值积分以及Monte-Carlo仿真实验对理论分析结果进行了验证。