翼型尾缘低频大功率合成射流的动态载荷特性研究——A：实验方案设计

为了获得翼型在尾缘合成射流作用下的气动特性,针对NACA0015翼型,设计了适用于风洞研究的尾缘合成射流实验,设计内容包括实验模型的设计,低频大功率合成射流致动器的设计,以及测量方案的设计。该实验方案在伺服电机达到适当转速时,合成射流器能够达到较好的吹／吸气效果。通过调节地面气缸的行程和电机的工作频率,可以实现对喷口速度、频率等参数的调节,为研究合成射流动量系数和减缩频率对气动力和力矩的影响规律提供了便利。针对二元实验段,采用自行设计的二分量应变天平测量动态升力和力矩。该实验模型在二元风洞中顺利开展了相关实验研究。研究结果显示,当合成射流频率为3Hz时,升力系数的幅值约为0．16。因此,尾缘低频大功率合成射流可以使翼型获得较大的用于控制气动弹性的控制力。这种新型作动方式为未来飞行器气动弹性稳定性控制提供了一种新途径。     

Lumped element modelling of synthetic jet actuators

In this paper, a lumped element model of synthetic jet actuator is presented and used to predict the temporal variation of the jet velocity. Unlike the previous model reported in the literature, in this model the mechanical movement of the diaphragm is decoupled from the fluid phenomenon in the actuator cavity to allow the modelling of fluid mechanics aspect of the actuator to be investigated and validated separately. Furthermore, the “minor losses” occurring at the orifice exit is included and linked to the jet exit velocity profile. The results from this model are validated using the existing experimental data and CFD simulations. It is found that this model is capable of predicting the temporal variation of synthetic jets both in phase and magnitude when the actuator is operating away from the Helmholtz resonance frequency. Although the model fails to predict the correct phase information at the Helmholtz resonance frequency, it can still produce the jet peak velocity that is in good agreement with the experimental data. The lumped element model presented in this paper can be used to provide a reliable prediction of the jet peak velocity needed in the initial design of synthetic jet actuators for practical applications.     

高速再入飞行器的制导与控制系统设计

 针对高速再入飞行器模型的快时变,强耦合,严重非线性的特点,采用反馈线性化方法,设计了自动驾驶仪;同时采用最优制导律设计与理想速度曲线相结合的方法,设计了能同时保证末端制导精度及速度方向、大小的制导律。最后,进行了六自由度仿真,结果表明 :设计的制导律及控制方案是合理、有效的,易于实现。     

A fault-tolerant triple-redundant voice coil motor for direct drive valves: Design, optimization, and experiment

A direct drive actuator (DDA) with direct drive valves (DDVs) as the control device is an ideal solution for a flight actuation system. This paper presents a novel triple-redundant voice coil motor (TRVCM) used for redundant DDVs. The TRVCM features electrical/mechanical hybrid triple-redundancy by securing three stators along with three moving coils in the same frame. A permanent magnet (PM) Halbach array is employed in each redundant VCM to simplify the system structure. A back-to-back design between neighborly redundancies is adopted to decouple the magnetic flux linkage. The particle swarm optimization (PSO) method is implemented to optimize design parameters based on the analytical magnetic circuit model. The optimization objective function is defined as the acceleration capacity of the motor to achieve high dynamic performance. The optimal geometric parameters are verified with 3D magnetic field finite element analysis (FEA). A research prototype has been developed for experimental purpose. The experimental results of magnetic field density and force output show that the proposed TRVCM has great potential of applications in DDA systems.     

高超声速飞行器舵面作动器舱环境设计及应用

针对高超声速飞行器热结构区域作动器舱环境控制相关技术进行研究,包括耐热结构可重复使用防热设计、外部热结构的作动器舱热防护构型设计和作动器舱动密封设计等。根据舱体的不同部位采用隔热式、辐射式和热沉式的防热构型,而作动器与舱体的运动间隙密封则采用一体式动密封构件。通过隔热特性分析、承载能力分析和热设计仿真分析等手段,优选出合理的热防护系统的适用参数。     

Design and experimental testing of a control system for a morphing wing model actuated with miniature BLDC motors

The paper deals with the design and experimental validation of the actuation mechanism control system for a morphing wing model. The experimental morphable wing model manufactured in this project is a full-size scale wing tip for a real aircraft equipped with an aileron. The morphing actuation of the model is based on a mechanism with four similar in house designed and manufactured actuators, positioned inside the wing on two parallel lines. Each of the four actuators used a BrushLess Direct Current (BLDC) electric motor integrated with a mechanical part performing the conversion of the angular displacements into linear displacements. The following have been chosen as successive steps in the design of the actuator control system: (A) Mathematical and software modelling of the actuator; (B) Design of the control system architecture and tuning using Internal Model Control (IMC) methodology; (C) Numerical simulation of the controlled actuator and its testing on bench and wind tunnel. The morphing wing experimental model is tested both at the laboratory level, with no airflow, to evaluate the components integration and the whole system functioning, but also in the wind tunnel, in the presence of airflow, to evaluate its behavior and the aerodynamic gain.     

Energy-saving and accurate motion control of a hydraulic actuator with uncertain negative loads

Pump controlled hydraulic actuators are wildly used in the aerospace industry owing to the advantages of energy-saving and integrated configurations. Negative loads may occur to actuators due to external force loads or the inertial force when the actuator decelerates significantly. Uncertain negative load working conditions may cause cavitation, actuator vibration, and even instability to the motion control if the actuator is without sufficient meter-out damping. Various types of hydraulic configuration schemes have been proposed to deal with negative loads of hydraulic actuators. However, few of them can simultaneously achieve energy saving and high control accuracy. This study proposes an energy-saving and accurate motion tracking strategy for a hydraulic actuator with uncertain negative loads. The actuator’s motion is driven by a servomotor pump, which gives full play to the advantage of energy-saving. The meter-out pressure is controlled by proportional valves to provide the optimized meter-out damping. The nonlinear adaptive robust control law is designed, which guarantees the control stability and achieve high tracking accuracy. An integrated direct/indirect adaptation law obtains satisfactory parameter estimations and model compensation for asymptotic motion tracking. Comparative experiments under different working conditions were performed to validate the advantages of the proposed control strategy.     

一种高灵敏度的电动舵机系统研究

本文研究了一种基于单片机的高灵敏、分体式小型电动舵机系统。首先分析了电动舵机的组成与功能，并分别从舵机结构、控制算法两方面对舵机系统的性能设计进行了分析和阐述。针对舵机高灵敏度的性能要求，对控制算法进行了优化并进行了相应仿真。最后经过试验验证，电动舵机满足了高灵敏度的指标要求，验证了控制算法的正确性。     

基于改进匈牙利算法的航空企业动态调度方法研究

航空零件生产调度时,应尽量满足多目标和实时性的要求。结合某航空制造企业的实际生产情况,提出一种基于"穷尽成对比较"技术和改进匈牙利算法的动态调度方法。首先以航空零件调度时的最大完工时间、生产加工成本以及生产能耗为优化目标,构建柔性作业车间多目标动态调度数学模型;然后利用基于"穷尽成对比较"技术的权重参数调节模型对数学模型中各个目标的权重参数进行实时动态调整;最后以各个目标的加权值为总目标,采用改进匈牙利算法求得工序的最优分配结果。结果表明:与传统的动态调度方法相比,动态调度方法能够有效地提高航空企业的生产效率、减少航空企业的生产加工成本并降低对环境的污染,具有较好的综合调度性能。     

高速开关阀在起落架半主动控制中的应用研究(英文)

To select or develop an appropriate actuator is one of the key and difficult issues in the study of semi-active controlled landing gear. Performance of the actuator may directly affect the effectiveness of semi-active control. In this article, parallel high-speed solenoid valves are chosen to be the actuators for the semi-active controlled landing gear and being studied. A nonlinear high-speed solenoid valve model is developed with the consideration of magnetic saturation characteristics and verified by test. According to the design rule of keeping the peak load as small as possible while absorbing the specified shock energy, a fuzzy PD control rule is designed. By the rule controller parameters can be self-regulated. The simulation results indicate that the semi-active control based on high-speed solenoid valve can effectively improve the control performance and reduce impact load during landing.     

Motion synchronization in a dual redundant HA/EHA system by using a hybrid integrated intelligent control design

This paper presents an integrated fuzzy controller design approach to synchronize a dis-similar redundant actuation system of a hydraulic actuator (HA) and an electro-hydrostatic actu-ator (EHA) with system uncertainties and disturbances. The motion synchronous control system consists of a trajectory generator, an individual position controller for each actuator, and a fuzzy force tracking controller (FFTC) for both actuators. The trajectory generator provides the desired motion dynamics and designing parameters of the trajectory which are taken according to the dynamic characteristics of the EHA. The position controller consists of a feed-forward controller and a fuzzy position tracking controller (FPTC) and acts as a decoupled controller, improving posi-tion tracking performance with the help of the feed-forward controller and the FPTC. The FFTC acts as a coupled controller and takes into account the inherent coupling effect. The simulation results show that the proposed controller not only eliminates initial force fighting by synchronizing the two actuators, but also improves disturbance rejection performance.     

飞行器服役（作战）完整性的提出与发展

飞行器服役完整性（对于军用飞行器也称为作战完整性）更综合地表征了飞行器在服役（作战）使用过程中的质量特性。本文首先介绍了飞行器服役（作战）完整性概念的提出过程,讨论了飞行器服役（作战）完整性的基本内涵和基本特性,阐明了飞行器服役（作战）完整性是飞行器服役（作战）适用性与飞行器服役（作战）效能发挥的基础。然后介绍了飞行器服役（作战）完整性的三种表征参数：飞行器固有完好率、飞行器固有健康度、飞行器服役（作战）完整度,并梳理了飞行器服役（作战）完整性优化设计的基本方法。最后提出了飞行器服役（作战）完整性的控制原理,指出了飞行器服役（作战）完整性发展的基础、研究方法和目前我国航空航天领域急需研究和发展的方向。     

应用等离子体进行翼型升力控制的数值模拟研究

将等离子体对中性气体的作用模型化为彻体力矢量,求解带源项的Navier-Stokes方程,数值模拟了在NLF(1)-0213翼型上表面60%弦长处安装等离子体激励器对升力的控制效果.彻体力为净电荷在外加电场作用下的电场力.解拉普拉斯方程得到外加电场分布,等离子体中的净电荷分布由泊松方程给出.升力线计算结果与实验值吻合,激励器工作时,升力线向上平移,控制效果与襟翼类似.     

双系统MCV主控阀8工作边配磨和性能检测技术

在大量工艺试验的基础上,对余度伺服作动器中MCV主控阀制造的核心技术进行了系统研究,总结出了一套完整的配套加工、重叠量配磨和流量特性检测和修整的技术方案,首次在国内实现了该项技术,并且实现了工程化生产。     

开孔曲面自动铺放轨迹规划算法研究

为解决开孔曲面自动铺放轨迹规划问题,提出在前处理中将孔边界内外的曲面接合成完整曲面的方法,采用STL文件提取网格化曲面信息并重构开孔曲面拓扑,按照设定算法获得“连续”的铺放轨迹后,再按孔边对轨迹点进行信息整理得到后置处理所需的最终铺放轨迹点信息.研究了迭代法和投影法在轨迹线与孔边界交点的求取方法,综合比较2种算法的效率和精度后,发现投影法更适于开孔曲面的轨迹规划.根据上述算法,编写了基于VC++ 6.0平台的轨迹规划程序,以整体复合材料前机身为例进行算法验证,证明了提出的开孔曲面自动铺放轨迹规划算法的合理性和正确性.     

基于滑模变结构和扩张状态观测器的电动舵机复合控制方法

为提高电动舵机伺服系统的鲁棒性,同时解决实际工作中电动舵机不确定负载引起的跟踪精度低的问题,提出了一种采用指数趋近率的滑模变结构控制率结合扩张状态观测器对负载扰动进行实时估计的电动舵机的伺服控制方法,给出了控制器设计方法和试验验证。仿真和试验结果表明,与常规的滑模控制器相比,采用扩张状态观测器的变结构控制能有效提高电动舵机的跟踪性能。     

基于泵式流体回路的小卫星姿控/热控一体化执行机构设计

 主要研究了小卫星姿控/热控一体化执行机构的设计问题.首先,根据流体回路中液体流速变化对小卫星产生力矩实现姿态控制、液体流动吸/散废热实现热控制的原理,提出一种姿控/热控一体化执行机构设计方案.然后针对该设计方案,利用以电机转速为变量的流体回路内压强和电磁力矩方程,推导了一体化执行机构姿控力矩模型;利用散热量随流体回路流速的变化,建立了一体化执行机构热控模型.最后,针对某小卫星设计了基于姿控/热控一体化执行机构的闭环控制系统,并针对该一体化执行机构设计了一种姿控/热控解耦算法,对其姿控/热控能力进行数学仿真验证,仿真结果证明了该一体化执行机构的有效性.     

Friction compensation for low velocity control of hydraulic flight motion simulator: A simple adaptive robust approach

Low-velocity tracking capability is a key performance of flight motion simulator (FMS), which is mainly affected by the nonlinear friction force. Though many compensation schemes with ad hoc friction models have been proposed, this paper deals with low-velocity control without friction model, since it is easy to be implemented in practice. Firstly, a nonlinear model of the FMS middle frame, which is driven by a hydraulic rotary actuator, is built. Noting that in the low velocity region, the unmodeled friction force is mainly characterized by a changing-slowly part, thus a simple adaptive law can be employed to learn this changing-slowly part and compensate it. To guarantee the boundedness of adaptation process, a discontinuous projection is utilized and then a robust scheme is proposed. The controller achieves a prescribed output tracking transient performance and final tracking accuracy in general while obtaining asymptotic output tracking in the absence of modeling errors. In addition, a saturated projection adaptive scheme is proposed to improve the globally learning capability when the velocity becomes large, which might make the previous proposed projection-based adaptive law be unstable. Theoretical and extensive experimental results are obtained to verify the high-performance nature of the proposed adaptive robust control strategy.     

ATP系统驱动装置设计

捕获、跟踪和瞄准（Acquisition,Tracking,Pointing—ATP）系统是飞行器激光通信与协同控制系统的重要组成部分。本文提出了基于激光反射的二维扫描ATP系统的总体解决方案,建立了扫描模块中关键器件的理论数学模型,实现了电路控制模块的硬件与软件界面的设计,最终搭建了ATP系统驱动装置。该装置响应迅速,结构紧凑,稳定性好,可完成120°视场的扫描以及视场中任意一点的定位。     

Dynamic thermal coupling modeling and analysis of wet electro-hydrostatic actuator

The electro-hydrostatic actuator(EHA) used in more electric aircraft(MEA) has been extensively studied due to its advantages of high reliability and high integration. However, this high integration results in a small heat dissipation area, leading to high-temperature problems. Generally,to reduce the temperature, a wet cooling method of using the pump leakage oil to cool the motor is adopted, which can also increase the difficulty of accurately predicting the system temperature in the early desi...