采用压电叠层作动器的弹性梁振动主动控制实验研究简

 结构响应主动控制系统中常用的惯性作动器由于附加质量大、工作频带窄和响应速度慢等缺点,降低了控制系统的性能。压电作动器具有质量轻、工作频带宽和响应速度快等优点,作为高效执行元件能有效地提高控制系统的性能。本文采用压电叠层作动器驱动自由-自由弹性梁模型,以观测点的加速度响应为控制目标,采用频域谐波稳态控制策略进行了自由梁结构谐波振动响应主动控制实验研究。实验结果表明,本文建立的采用压电叠层作动器的结构响应主动控制系统能有效地控制弹性梁结构的振动水平,并具有快速跟踪外激励变化的自适应控制能力。     

采用压电叠层作动器的弹性梁振动主动控制实验研究

结构响应主动控制系统中常用的惯性作动器由于附加质量大、工作频带窄和响应速度慢等缺点,降低了控制系统的性能。压电作动器具有质量轻、工作频带宽和响应速度快等优点,作为高效执行元件能有效地提高控制系统的性能。本文采用压电叠层作动器驱动自由-自由弹性梁模型,以观测点的加速度响应为控制目标,采用频域谐波稳态控制策略进行了自由梁结构谐波振动响应主动控制实验研究。实验结果表明,本文建立的采用压电叠层作动器的结构响应主动控制系统能有效地控制弹性梁结构的振动水平,并具有快速跟踪外激励变化的自适应控制能力。     

一种高灵敏度的电动舵机系统研究

本文研究了一种基于单片机的高灵敏、分体式小型电动舵机系统。首先分析了电动舵机的组成与功能，并分别从舵机结构、控制算法两方面对舵机系统的性能设计进行了分析和阐述。针对舵机高灵敏度的性能要求，对控制算法进行了优化并进行了相应仿真。最后经过试验验证，电动舵机满足了高灵敏度的指标要求，验证了控制算法的正确性。     

基于滑模变结构和扩张状态观测器的电动舵机复合控制方法

为提高电动舵机伺服系统的鲁棒性,同时解决实际工作中电动舵机不确定负载引起的跟踪精度低的问题,提出了一种采用指数趋近率的滑模变结构控制率结合扩张状态观测器对负载扰动进行实时估计的电动舵机的伺服控制方法,给出了控制器设计方法和试验验证。仿真和试验结果表明,与常规的滑模控制器相比,采用扩张状态观测器的变结构控制能有效提高电动舵机的跟踪性能。     

变质心飞行器伺服机构模糊PI控制技术研究

概述了飞行器质心调节机构的技术特点,针对某质心调节机构的伺服控制需求,设计了一种模糊PI控制器,建立了质心调节机构数学模型,完成了仿真分析与实验研究。仿真与实验研究结果表明,模糊PI控制器结合了PI控制器高精度和模糊控制器控制快速、适应性强的特点,使系统具有较快的响应性能和较高的控制精度,同时有较强的鲁棒性。研究成果对于提高变质心飞行器的机动性能有着重要的意义。     

超磁致伸缩电静液作动器的试验研究与特性分析

超磁致伸缩材料驱动的电静液作动器具有结构高度集成、性能影响因素多以及理论分析复杂等特点,为寻求超磁致伸缩电静液作动器可靠的理论分析方法以提高其输出性能,首先搭建了超磁致伸缩执行器与作动器试验测试平台,完成了执行器与作动器动态特性对比试验,在准确测试与观察试验现象的基础上,对超磁致伸缩电静液作动器进行结构分解,以各环节固有频率为理论分析切入点,采用试验、理论与有限元分析相结合的方法,分析了悬臂梁阀片、管路、液压缸以及蓄能器等动态特性对作动器输出性能的影响规律,总结出符合试验结果的理论分析方法并确定了影响与制约作动器输出性能的关键环节,最后提出了超磁致伸缩电静液作动器优化改进方案,优化后作动器试验结果显示：在200 Hz左右、0.6 MPa 的偏压作用下,选取 0.15 mm 厚度的阀片,作动器的输出性能达到最佳,其输出流量最大可达1.2 L/min。     

形状记忆合金扭力驱动器的力学模型和实验研究

扭力驱动是自适应翼面驱动技术中的一个关键问题。将镍钛形状记忆合金 (Ni Ti SMA)丝与薄壁圆管相结合,可以构成 SMA扭力驱动器。介绍了 SMA扭力驱动器的构造,建立了扭力驱动器在激励过程中的力学模型,分析了驱动器的扭转角与温度之间的关系,并进行了实验验证。     

Matching design of hydraulic load simulator with aerocraft actuator

 This paper intends to provide theoretical basis for matching design of hydraulic load simulator (HLS) with aerocraft actuator in hardware-in-loop test, which is expected to help actuator designers overcome the obstacles in putting forward appropriate requirements of HLS. Traditional research overemphasizes the optimization of parameters and methods for HLS controllers. It lacks deliberation because experimental results and project experiences indicate different ultimate performance of a specific HLS. When the actuator paired with this HLS is replaced, the dynamic response and tracing precision of this HLS also change, and sometimes the whole system goes so far as to lose control. Based on the influence analysis of the preceding phenomena, a theory about matching design of aerocraft actuator with HLS is presented, together with two paired new concepts of "Standard Actuator" and "Standard HLS". Further research leads to seven important conclusions of matching design, which suggest that appropriate stiffness and output torque of HLS should be carefully designed and chosen for an actuator. Simulation results strongly support that the proposed principle of matching design can be anticipated to be one of the design criteria for HLS, and successfully used to explain experimental phenomena and project experiences.     

基于AMESim的直升机液压助力器建模与仿真

介绍了直升机飞行操纵系统典型液压助力器的组成和工作原理,对助力器静动态性能分析方法进行了研究。综合考虑不可忽视液压刚度、结构刚度、摩擦、泄漏等非线性因素对系统的影响,建立了基于AMESim的助力器模型。利用该模型对直升机飞行操纵系统样例液压助力器进行仿真分析,将仿真结果和试验结果进行验证对比,结果表明仿真数据和试验数据基本吻合,较好地反映了实际系统的性能。因此仿真结果可以为直升机飞行操纵系统液压助力器打样设计和结构优化提供理论分析依据。     

DDV作动器余度数字伺服系统工程设计与实现

 介绍一种直接驱动阀（DDV）式作动器的余度数字式伺服系统设计与实现,描述了系统的余度配置、设计思想及组成,建立了DDV作动器的结构参数化模型及数字伺服回路的模型,并进行了仿真,分析了作动器动静态特性、采样频率及监控器的设计性能。最后,采用快速原型实时仿真,对余度数字式伺服系统完成了的性能试验验证,结果表明系统性能令人满意。     

直升机后缘襟翼驱动器迟滞现象仿真与抑制

直升机后缘襟翼多采用压电驱动器作为驱动元件，但是在使用过程中压电驱动器迟滞会对其振动控制性能产生不利影响，因此针对压电驱动器迟滞开展了迟滞建模与抑制研究。通过实验研究了压电驱动器在不同驱动频率下的迟滞特性，采用Bouc-Wen模型对驱动器迟滞现象进行了建模，并采用粒子群算法（PSO）辨识模型参数，与实际测量迟滞曲线进行了对比，在10~60 Hz范围内所建立的迟滞模型能够较为精确地描述压电驱动器迟滞现象。建立了基于Bouc-Wen逆模型的前馈补偿控制与PID反馈控制相结合的复合控制策略，实验结果显示该控制策略能够在10~60 Hz较宽的频率范围内有效抑制该压电驱动器迟滞现象。建立了考虑驱动器迟滞的主动控制后缘襟翼振动控制动力学模型，并对中等速度稳态前飞条件下后缘襟翼振动控制性能进行了仿真，仿真结果显示驱动器迟滞会在一定程度上削弱振动控制性能，而采用复合控制可以提高后缘襟翼旋翼振动控制性能。     

Reconfigurable fault-tolerant control for supersonic missiles with actuator failures under actuation redundancy

Aircraft undergoing actuator failures into under-actuation have been seldom studied in literature. Aiming at addressing actuator failures of Total Loss of Effectiveness (TLOE) as well as Partial Loss of Effectiveness (PLOE) resulting in different system actuations, reconfigurable Fault-Tolerant Control (FTC) is proposed for supersonic wingless missiles under actuation redundancy. The under-actuated system of TLOE failure patterns is solved by transformation to cascade systems through a ‘shape variable’. Meanwhile, actuator TLOE faults of different unknown failure patterns from proper actuation to under-actuation are accommodated by a reconfigurable adaptive law on a multiple-model basis. The backstepping technique with the Extended State Observer (ESO) method adopted as a basic strategy is applied to an established symmetric coupled missile system with actuator PLOE faults, modeling errors, and external disturbances. Additionally, the nonlinear saturation characteristics of actuators are settled by an auxiliary system with the Nussbaum function technique. The stability of the control system is analyzed and proven through Lyapunov theory. Numerical simulations are implemented in the presences of aerodynamic uncertainties, gust disturbance, and actuator failures. Results demonstrate the effectiveness of the proposed method with satisfactory tracking performance and actuator fault tolerance capacity.     

航空发动机分布式控制系统动态输出反馈鲁棒H∞容错控制

针对存在网络诱导时延、外部干扰的航空发动机分布式控制系统,提出了执行机构发生部分失效故障时的输出反馈容错控制方法。对航空发动机分布式控制系统中网络诱导时延以及执行器部分失效问题进行量化说明,在此基础上,采用动态输出反馈控制器建立增广闭环系统。针对所建立的增广闭环系统,对H∞性能约束下的增广闭环系统稳定性进行分析,并利用线性矩阵不等式理论设计了输出反馈H∞容错控制器。仿真结果表明,当两个执行机构输出值分别为衰减80%和50%时,控制系统在所设计的控制器作用下均方渐进稳定,且具有H∞性能指标为0.63,同样在正向偏差故障条件下也具有很好的容错能力。      

Dynamic Modeling of Brushless dc Motors for Aerospace Actuation

A discrete time model for simulation of the dynamics of samarium cobalt-type permanent magnet brushless dc machines is presented. The similation model includes modeling of the interaction between these machines and their attached power conditioners. These are transistorized conditioner units. This model is part of an overall discrete-time analysis of the dynamic performance of electromechanical actuators, which was conducted as part of prototype development of such actuators studied and built for NASA-Johnson Space Center as a prospective alternative to hydraulic actuators presently used in shuttle orbiter applications. The resulting numerical simulations of the various machine and power conditioner current and voltage waveforms gave excellent correlation to the actual waveforms collected from actual hardware experimental testing. These results, numerical and experimental, are presented here for machine motoring, regeneration and dynamic braking modes. Application of the resulting model to the determination of machine current and torque profiles during closed-loop actuator operation were also analyzed and the results are given here. These results are given in light of an overall view of the actuator system components. The applicability of this method of analysis to design optimization and trouble-shooting in such prototype development is also discussed in light of the results at hand.     

Fault Detection and Diagnosis of Aircraft Actuators using Fuzzy-Tuning IMM Filter

This paper proposes a new interacting multiple model (IMM) filter for actuator fault detection. Since each individual filter of the IMM filter uses the combined information of the estimation values from all the operating filters, it can effectively estimate system parameter variations, thereby it can diagnose the actuator damage with an unknown magnitude. In this study, to diagnose the actuator failure fast and accurately, fuzzy logic is used to tune a transition probability among multiple models. This makes the fault detection process smooth and reduces the possibility of false fault detection. Also, a discrete fault tolerant command tracker is derived to cope with actuator damages. To validate the performance of the proposed fault detection and diagnosis (FDD) algorithm, numerical simulations are performed for a high performance aircraft system.     

航空发动机燃油系统执行机构故障诊断及验证

研究了基于执行机构模型以及发动机逆模型的发动机燃油系统执行机构及其传感器故障诊断方法.基于发动机半物理仿真试验台试验数据建立执行机构小闭环传递函数模型,通过二次多项式拟合将油针位置转换为燃油流量.提出基于自校正在线训练神经网络算法建立发动机逆模型,以离线训练网络参数初始化在线系统,基于阈值更新网络参数,并对学习速率进行自校正,以提高算法的泛化能力及收敛速度.对比执行机构模型输出、发动机逆模型输出与LVDT传感器测量位移换算得到的燃油流量,基于阈值判断故障状态.在T700涡轴发动机半物理仿真试验平台上进行试验,实现了在发动机额定及各种性能退化状态下,执行机构及其传感器漂移和偏置故障的准确诊断及定位,验证了算法的有效性.     

电动舵系统颤振影响因素分析

针对电动舵系统颤振问题,将舵系统简化为双惯量模型,并在该模型的基础上分析了舵系统颤振的原因.通过对舵系统传递函数以及单自由度碰撞振动系统力学模型的分析,得出传动机构刚度、间隙等非线性因素以及负载惯量对舵系统稳定性的影响,并分析了各因素造成舵系统颤振的原因.通过数学仿真,验证了所得结论的正确性,并针对颤振抑制提出了相应的改进措施.     

Design and experimental testing of a control system for a morphing wing model actuated with miniature BLDC motors

The paper deals with the design and experimental validation of the actuation mechanism control system for a morphing wing model. The experimental morphable wing model manufactured in this project is a full-size scale wing tip for a real aircraft equipped with an aileron. The morphing actuation of the model is based on a mechanism with four similar in house designed and manufactured actuators, positioned inside the wing on two parallel lines. Each of the four actuators used a BrushLess Direct Current (BLDC) electric motor integrated with a mechanical part performing the conversion of the angular displacements into linear displacements. The following have been chosen as successive steps in the design of the actuator control system: (A) Mathematical and software modelling of the actuator; (B) Design of the control system architecture and tuning using Internal Model Control (IMC) methodology; (C) Numerical simulation of the controlled actuator and its testing on bench and wind tunnel. The morphing wing experimental model is tested both at the laboratory level, with no airflow, to evaluate the components integration and the whole system functioning, but also in the wind tunnel, in the presence of airflow, to evaluate its behavior and the aerodynamic gain.     

基于数值模拟的NSDBD等离子体激励器防冰特性

飞行器表面在一定气象条件下会产生积冰,积冰会使飞行器气动性能下降,是危害飞行安全的重要因素之一。常见的气热及电热防冰系统已经广泛运用于现有飞行器上。近些年,在纳秒脉冲阻挡介质放电（NSDBD）等离子体激励器的相关研究中发现NSDBD等离子体激励器可对周围流场进行快速加热,考虑到这种热效应可能作为飞机防冰的一种新方式。本文用数值方法对NSDBD等离子体激励器防冰特性开展了研究。首先,建立了基于Messinger模型的积冰模型,对典型积冰条件进行了验证计算;其次,耦合唯象学等离子体模型与非定常雷诺平均Navier-Stokes方程,计算等离子体对空气流场的影响;最后,将NSDBD等离子体激励器布置在NACA0012翼型前缘防冰区,结合积冰模型与唯象学等离子模型,对其防冰特性进行了研究。计算结果表明等离子体加热的热气流会覆盖在翼型表面防冰区。在相同的霜冰条件下,开启等离子体激励器时机翼前缘没有出现积冰,说明等离体子激励器应用于机翼防冰是有效的。针对不同的激励器参数对防冰特性的影响规律进行了研究,总体上防冰效果与峰值电压、激励器频率有关,从防冰效果和能耗方面考量,在给定计算条件下,存在最优电压值和最优激励器频率值。激励器分布方式对防冰特性的影响与其具体流场有关,需要具体分析。     

介质阻挡放电对增升装置气动性能的影响

增升装置是传统构型飞机的重要组成部分,对飞行器气动性能有重要影响。将高效、简便、节能的介质阻挡放电(Dielectric Barrier Discharge,DBD)等离子体激励器布置在增升装置附近,通过对流场进行控制来达到提高增升装置气动性能的作用。选取二维翼型GAW-1及其29%襟翼作为研究对象,在分析基础流场的基础上,固定激励器放电频率等参数不变,将单级介质阻挡放电激励器放置在几个不同位置,用数值模拟的方法研究其对翼型总体气动特性的影响。仿真结果表明,主翼上表面后缘处的激励器增升效果最好,增升达12.8%且将失速迎角推迟约2°,主翼下表面后缘的升阻比增加可达15%。