A Modified Discrete Karhunen-Loeve Random Field Estimator

Based upon the modified Karhunen-Loeve model of the gravity disturbance vector proposed by us recently, a corresponding Karhunen-Loeve random field estimator is developed in this paper for a two-dimensional grid of gravity data in a local finite region.The new eigenvectors obey the "required" orthogonality relations on the chosen grid provided the KL expansion is now separated into odd and even integers. The closed-form solution of the estimator isthen obtained under the "diagonal" assumption for the gain coefficients. It is shown that this assumption, without which nosolution is possible, enables the estimator to reproduce the data atgrid points when the noise in the data is absent and the number of terms in the Karhunen-Loeve expansion are equal to the number of grid points.     

Comprehensive compensation method for the influence of disturbing gravity field on long-range rocket guidance computing

With the improvement of the accuracy of the inertial system, the influence of the disturbing gravity field on the accuracy of long-range rocket has become increasingly prominent. However, in actual engineering, there are problems of low accuracy and being time-consuming for disturbing gravity field compensation. In view of this, this paper proposes a set of online comprehensive solutions combining disturbing gravity reconstruction and stellar correction. According to the pre-launch binding param...     

Error Covariance Analysis of a Karhunen-Loeve Random Field Estimator

An error covariance analysis of a two-dimensional Karhunen-Loeve random field estimator (KLE) for gridded gravity data is presented without actually using the data. Attention is focused particularly on the north-south deflection component of the disturbance vector so that the rms value of its residual error may not exceed 3 percent of the signal rms for grid spacing of not less than 5 nm, when signal-to-noise ratio in the data is varied within reasonable limits. To achieve this rather stringent goal, a discrete KLE derived entirely from a two-dimensional grid configuration is needed. The KLE for geodesy applications was developed initially by Bose. Using continuous measurements and the orthogonality relations of the Karhunen-Loeve (KL) eigenvectors in a continuous domain, continuous KL gain coefficients ?mnj and consequently the continuous KL gain vector Kmn were obtained; thus a satisfactory continuous KLE was achieved. However the discrete version of the KLE was then given by keeping the old (continuous) ?mnj, and simply computing the KL eigenvectors on the grid coordinates to evaluate the discrete KL gain vector Kmn. Clearly this is not a satisfactory discrete KLE since , ?mnj are not constants but rather depend on the measurement noise variances. So if the measurements are now going to be discrete, one must rederive ?mnj for this situation.     

基于动基座重力梯度仪的导弹主动段飞行状态估计

弹道导弹主动段由于惯导系统工具误差和扰动引力的影响,使得导弹关机点状态参数偏离标准关机状态参数,大大影响了导弹的命中精度.为此,提出了基于动基座重力梯度仪的导弹主动段飞行状态估计方案,利用动基座重力梯度仪测得的导弹实际位置引力梯度信息,采用卡尔曼滤波方法,修正导弹当前的飞行状态.通过初步仿真,证明该方法理论上是可行的.     

重力和重力梯度基准图构建的多参量联合网格化

高精度、高分辨率的重力及重力梯度基准图是决定潜艇水下辅助导航定位精度的关键因素。我国海洋重力测量目前的主要比例尺为1:1000000，在局部区域可达1:500000，测线间隔分布相对稀疏。传统的网格化插值技术在远离测点位置时容易产生虚假异常，或异常特征发生偏移。构建了全张量重力梯度数据的6个梯度分量的联合网格化方法,利用各个梯度分量与引力位在波数域中的关系重构了引力位，实现了重力和重力梯度数据的再计算，从而实现了网格处理。通过模型数据和实测数据，验证了该方法在插值异常分辨率和位置准确性上具有优势。     

Theoretical modeling of vectoring dual synthetic jet based on regression analysis

The excellent vectoring characteristic of Dual Synthetic Jet (DSJ) provides a new control strategy for the active flow control, such as thrust vectoring control, large area cooling, separated flow control and so on. For incompressible flow, the influence relation of source variables, such as structure parameters of actuators, driving parameters and material attributes of piezoelectric vibrating diaphragm, on the vectoring DSJ and a theoretical model are established based on theoretical and regression analysis, which are all verified by numerical simulations. The two synthetic jets can be deemed as a main flow with a higher jet velocity and a disturbing flow with a lower jet velocity. The results indicate that the influence factors contain the low-pressure area formed at the exit of the disturbing flow, which could promote the vectoring deflection, and the impact effect of the disturbing flow and the suppressive effect of the main flow with the effect of restraining the vectoring deflection. The vectoring angle is a complex parameter coupled by all source variables. The detailed theoretical model, whose error is controlled within 3.6 degrees, can be used to quantitatively assess the vectoring feature of DSJ and thus to provide a guidance for designing the control law applied in the active flow control.     

液体火箭发动机稳态故障仿真及分析

建立了液体火箭发动机稳态故障数学模型，编制了实用计算程序。调整方程组中的有关系数的参数，该模型既可用于在正常工况下评定性能参数随干扰因素的随机变化，进行发动机静态特性仿真。又可用于在故障状态下发动机性能参数衰减退化的计算，进行发动机稳态故障效应的仿真。     

Inertial navigation system synthesis approach and gravity-inducederror sensitivity

A design criterion for improving the performance of the speed-damped inertial navigation system is presented. The single-axis speed-damped system is approached by optimizing the response of the system to a step-function disturbing signal. Butterworth, integral of time-multiplied absolute-value of error (ITAE), and solution-time standard forms are assumed to be the figures of merit for optimizing the system performance. The steady-state RMS (root-mean-square) gravity-induced navigation errors that are excited in the speed-damped system are determined for two gravity uncertainty models. The proposed figures of merit are compared. These comparisons reveal the sensitivity of predicted navigation errors to uncertainties in the gravity statistics, and simplify the choice of a suitable figure of merit for use in the design and error analysis of inertial navigation systems     

风洞模型投放试验轻模型法重力效应影响

风洞模型投放试验是研究超声速机弹分离问题的一种有效手段，相似参数的选取是影响试验准度的关键因素。有初始弹射速度的超声速机弹分离研究中，通常采用"轻模型法"得到模型的运动学及动力学相似参数，但该相似参数中模型重力模拟不足。为了研究重力效应对投放试验结果的影响，采用CTS试验技术对全尺寸真实参数与缩比尺寸轻模型法相似参数条件下得到的结果进行了对比研究。研究结果表明：在载弹与载机分离过程中，载弹位姿相互耦合，垂直下落位移的快慢会影响载弹姿态角的变化；轻模型法相似参数条件下，载弹垂直下落位移较慢，虚拟重力的修正方法只能近似修正下落位移，不能对导弹姿态角进行修正，而姿态角会影响下落的位移；机弹分离安全性方面，轻模型法相似参数条件下的试验结果较真实参数偏危险。     

Fuzzy adaptive robust control for space robot considering the effect of the gravity

Space robot is assembled and tested in gravity environment, and completes on-orbit service（OOS） in microgravity environment. The kinematic and dynamic characteristic of the robot will change with the variations of gravity in different working condition. Fully considering the change of kinematic and dynamic models caused by the change of gravity environment, a fuzzy adaptive robust control（FARC） strategy which is adaptive to these model variations is put forward for trajectory tracking control of space robot. A fuzzy algorithm is employed to approximate the nonlinear uncertainties in the model, adaptive laws of the parameters are constructed, and the approximation error is compensated by using a robust control algorithm. The stability of the control system is guaranteed based on the Lyapunov theory and the trajectory tracking control simulation is performed. The simulation results are compared with the proportional plus derivative（PD） controller, and the effectiveness to achieve better trajectory tracking performance under different gravity environment without changing the control parameters and the advantage of the proposed controller are verified.     

Deep and Shallow Solid-Earth Structures Reconstructed with Sequential Integrated Inversion (SII) of Seismic and Gravity Data

In this paper, the possibility of using simultaneously seismic and gravity data, for the reconstruction of solid-Earth structures, has been investigated through the use of an algorithm which allows joint efficient and reliable optimisation of compressional velocity and mass density parameters. We view the measured data as a realisation of a stochastic process generated by the physical parameters to be sought and we construct a “probability density function” which includes three kinds of information: information derived from gravity measurements; information derived from seismic travel time inversion and information on the physical correlation among density and velocity parameters. We show that combining data has a beneficial effect on the inversion since: it makes the problem more stable and as a consequence, providing that the quality of data is sufficiently high, enables more accurate and reliable reconstruction of the unknown parameters. In this context, we look forward the GOCE mission, which promises high spatial resolution (100–200 km) and accurate (1–2 mGals) gravity data. We show results obtained from data sets calculated for a lateral inhomogeneous earth synthetic model and from seismic and gravity field data analysed: — in the framework of TOMOVES (TOMOgraphy of Mt. VESuvius) experiment, an European project aiming at reconstructing the 3-D image of Mt. Vesuvius volcano and the crust underneath. using high resolution seismic tomography techniques and other geophysical methods; — for a profile inserted in a project aiming at reconstructing the crustal structure between Corsica and the Northern Appennines which crosses the Ligurian Sea and cuts the Ligurian Appennines W of La Spezia, extending up to Parma. This revised version was published online in August 2006 with corrections to the Cover Date.     

Combined Use of Altimetry and In Situ Gravity Data for Coastal Dynamics Studies

Accurate local geoids derived from in situ gravity data will be valuable in the validation of GOCE results. In addition it will be a challenge to use GOCE data in an optimal way, in combination with in situ gravity, to produce better local geoid solutions. This paper discusses the derivation of a new geoid over the NW European shelf, and its comparison with both tide gauge and altimetric sea level data, and with data from ocean models. It is hoped that over the next few years local geoid methods such as these can be extended to cover larger areas and to incorporate both in situ and satellite measured gravity data. This revised version was published online in August 2006 with corrections to the Cover Date.     

大型挠性充液卫星的动力学模型

研究了带有多个挠性附件和液体燃料贮箱的中继卫星系统的动力学建模问题。给出了微重力下小幅线性晃动等效模型基本参数，用混合坐标法描述中继卫星系统的构形，利用虚功原理推导出的矩阵形式的中继卫星动力学模型简洁且具有一般性，适用于许多开链飞行器系统。     

基于A*和TEB融合的行人感知无碰跟随方法

移动机器人通过跟随一个指定行人实现导航是一种便捷的方式。针对行人跟随中的机器人跟随和避障问题,提出了一种基于路径规划的无碰跟随方法。该方法结合激光点云分割提供的非行人障碍信息生成静态障碍代价地图,并根据3D行人定位结果,利用基于无迹卡尔曼滤波器（Unscented Kalman Filter,UKF）和最近邻联合概率数据关联（Nearest Near Joint Probabilistic Data Association,NN-JPDA）的多行人跟踪器估计干扰行人运动状态,进而生成动态行人代价地图。在此基础上,基于A^*的全局规划器结合静态障碍代价地图输出指向目标行人的全局路径,而基于时间弹性带（TEB）算法的局部规划器也将动态行人代价地图纳入考虑范围以规划优化的局部路径,这能够帮助机器人实现行人感知的避障且跟随全局路径。通过低频全局规划与高频局部规划结合的方式实现对目标行人安全无碰的跟随。实验验证了所提方法的有效性。     

基于力位协同控制的大飞机机身壁板装配调姿方法

为校正中机身壁板由于重力和调姿内力产生的变形，提高中机身壁板装配调姿精度，提出了一种基于力位协同控制的装配调姿方法。通过将调姿机构等效为并联机构，推导了调姿机构的解析正反解模型；根据螺旋理论，建立了力传感器测量值与重力、调姿内力之间的映射关系，实现重力补偿值的动态计算，基于局部刚体-弹性连接假设，通过多元线性回归方法构建了调姿内力转化为位置补偿量的模型；根据Clamped-Free变形协调原理，简化了定位器调姿内力之间的协调关系，在此基础上提出了重力前馈补偿和调姿内力转化为位置补偿的力位协同控制策略，并对其进行了理论分析与设计。最后，对所提出的控制策略进行了仿真分析，结果表明采用力位协同控制方法，调姿定位精度提高35.3%，调姿内力降低77.8%，通过应用实验，说明了该方法的可行性和有效性。     

Improving the process forming limit considering forming defects in the transitional region in local loading forming of Ti-alloy rib-web components

The isothermal local loading forming technology provides a feasible way to form Ti-alloy large-scale rib-web components in aerospace and aviation fields.However,the local load ing process forming limit is restricted by forming defects in the transitional region.In this work,the feasibility of controlling forming defects and improving the process forming limit by adjusting die parameters is explored through finite element (FE) simulation.It is found that the common cavum and folding defects in the transitional region are significantly influenced by the fillet radii of left rib and middle rib,respectively.The cavum and folding defects can be effectively controlled by increas ing the fillet radii of left rib and middle rib,respectively.The process forming limits considering forming defects in the transitional region are determined by the stepwise searching method under various die parameters.Moreover,the relationship between the process forming limit and die parameters is developed through the response surface methodology (RSM).The developed RSM models suggest that increasing the fillet radii of left and middle ribs is effective to improve the pro cess forming limit during local loading forming of rib-web components.The results will provide technical basis for the design of die parameters and the reduction amount,which is of great impor tance to control forming defects and improve the process forming limit in local loading forming of Ti-alloy large-scale rib-web components.     

重力传感器参数双轴旋转调制标定方法及实验验证

重力传感器参数的外场标定可充分发挥重力仪的测量潜力，提高重力测量的精度。利用全局可观性方法，对加速度计在静态条件下的参数可观性进行了分析，推导了静态多位置条件下加速度计参数可观的条件。根据理论推导的参数可观的条件，以双轴旋转重力仪为实验平台，设计了标定参数的编排方案。实验结果表明，该方法所测得的刻度因数对角线的最大偏差达到了10-8量级，利用对角线上的刻度因子修正了三轴转台的标定结果。2800s纯惯导解算结果证明，使用外场标定参数与实验室三轴转台标定参数的纯惯性导航精度相当。     

考虑重心位置不确定性的无尾无人机优化设计

飞机的飞行性能与重心(CG)位置密切相关,尤其是后掠式无尾飞机的重心位置对其飞行性能影响更甚,如果重心位置发生变化,升力分布随之改变,进而影响飞机航时。针对这个问题,从气动布局和设计方法两方面,设计了一种航时对重心位置不敏感的无尾无人机(UAV)。气动布局上,提出了利用螺旋桨动力配平纵向力矩的鸥翼(GW)布局,以减小重心位置变化对升阻特性的影响;设计方法上,采用稳健性优化设计(RDO)理论,分析重心位置不确定时的航时低敏感度问题。以一架小型电动无人机为研究对象,建立了无尾无人机稳健性优化设计环境,包括总体设计、代理模型构造以及稳健性优化。分析结果表明:利用螺旋桨动力配平的鸥翼布局使重心可用范围增加了5%;静安定裕度在5%~15%变化时,该布局可以有效提高航时稳健性。采用稳健性优化得到的无人机几何参数,大幅度降低了重心位置对航时的影响,显著提升了满足约束的概率。     

非同心型挤压油膜阻尼器的试验和理论研究

本文介绍非同心型挤压油膜阻尼器在非对称模型转子和燃气涡轮发动机上的试验和理论研究。挤压油膜阻尼器能有效地抑制和减小传递到支承结构上的振动力。理论研究与试验结果是吻合的。本文推荐非同心型挤压油膜阻尼器设计方法。      

小卫星主动磁控制地球捕获姿态控制系统设计

分析了小卫星捕获阶段的客观条件要求,重力梯度杆的指向要求,捕获阶段视为大角度机动问题,采用欧拉动力学和四元数方法描述,建立小卫星捕获阶段的动力学模型。控制器采用大角度机动拟 PD控制,拟PD控制器参数采用了简化分析和经验调试设计,同时分析设计了磁力矩器的磁偶极子,最后给出某小卫星姿态捕获仿真结果,经过几个轨道周期后可以实现一定精度的对地捕获,验证了本文的设计方法的可行性。