Spacecraft formation flying for Earth-crossing object deflections using a power limited laser ablating

A formation flying strategy with an Earth-crossing object (ECO) is proposed to avoid the Earth collision. Assuming that a future conceptual spacecraft equipped with a powerful laser ablation tool already rendezvoused with a fictitious Earth collision object, the optimal required laser operating duration and direction histories are accurately derived to miss the Earth. Based on these results, the concept of formation flying between the object and the spacecraft is applied and analyzed as to establish the spacecraft’s orbital motion design strategy. A fictitious “Apophis”-like object is established to impact with the Earth and two major deflection scenarios are designed and analyzed. These scenarios include the cases for the both short and long laser operating duration to avoid the Earth impact. Also, requirement of onboard laser tool’s for both cases are discussed. As a result, the optimal initial conditions for the spacecraft to maintain its relative trajectory to the object are discovered. Additionally, the discovered optimal initial conditions also satisfied the optimal required laser operating conditions with no additional spacecraft’s own fuel expenditure to achieve the spacecraft formation flying with the ECO. The initial conditions founded in the current research can be used as a spacecraft’s initial rendezvous points with the ECO when designing the future deflection missions with laser ablation tools. The results with proposed strategy are expected to make more advances in the fields of the conceptual studies, especially for the future deflection missions using powerful laser ablation tools.     

Encounter trajectories for deep space mission ASTER to the triple near Earth asteroid 2001-SN263. The laser altimeter (ALR) point of view

In cooperation with Russia, the Brazilian deep space mission ASTER plans to send a small spacecraft to investigate the triple asteroid 2001-SN263. The nearest launch opportunities for this project include June 2022 and June 2025. One main exploration campaign is being planned with focus on the largest asteroid (Alpha). Among the instruments under development, a laser altimeter (named ALR) was preliminarily designed and presented in 2010–2011. Many studies to define mission and instruments requirements were performed aiming at the characterization of important issues for the successful realization of the mission. Among them, the identification of a suitable trajectory that could be followed by the ASTER spacecraft in the encounter phase, when the main campaign will take place. This paper describes the effort undertaken with focus on the laser altimeter operation. Possible encounter trajectories were modelled and simulated to identify suitable approach parameters and conditions allowing the accomplishment of the intended investigation. The simulation also involves the instrument operation, considering approach geometry, attitude, relative motion, time/date, and the dynamics of the main asteroid. From the laser altimeter point of view, keeping in mind the desired coverage results (50% minimum surface coverage of asteroid Alpha, complying with horizontal and vertical resolution requirements), results point out crucial features for the encounter trajectory, like the need for a small inclination (10^-6 degrees; with respect to the asteroid's orbit), the most favourable spacecraft positioning (between the Sun and the asteroid) and pointing condition (back to the Sun), the minimum amount of achievable surface coverage (58%, focused on central areas), and the most proper time to conduct the main campaign (January 2025). Concerning the instrument, results offer refined values for divergence angle (500 to 650 μrad, half-cone), pulse repetition frequencies (from 1/20 to 1 Hz), and consequent data generation rates. A simulation tool that can use any 3D generated trajectories as input data was created for the analyses presented here. Although created for the ALR in this mission, this simple analysis tool can be adapted to other instruments in this or other missions.     

Micro-meteoroids and space debris impact risk assessment for the ConeXpress satellite using ESABASE2/Debris

Micro-meteoroid and space debris impact risk assessments are performed to investigate the risk from hypervelocity impacts to sensitive spacecraft sub-systems. For these analyses, ESA’s impact risk assessment tool ESABASE2/Debris is used. This software tool combines micro-particle environment models, damage equations for different shielding designs and satellite geometry models to perform a detailed 3D micro-particle impact risk assessment. This paper concentrates on the impact risk for exposed pressurized tanks. Pressure vessels are especially susceptible to hypervelocity impacts when no protection is available from the satellite itself. Even small particles in the mm size range can lead to a fatal burst or rupture of a tank when impacting with a typical collision velocity of 10–20 km/s. For any space mission it has to be assured that the impact risk is properly considered and kept within acceptable limits. The ConeXpress satellite mission is analysed as example. ConeXpress is a planned service spacecraft, intended to extend the lifetime of telecommunication spacecraft in the geostationary orbit. The unprotected tanks of ConeXpress are identified as having a high failure risk from hypervelocity impacts, mainly caused by micro-meteoroids. Options are studied to enhance the impact protection. It is demonstrated that even a thin additional protective layer spaced several cm from the tank would act as part of a double wall (Whipple) shield and greatly reduce the impact risk. In case of ConeXpress with 12 years mission duration the risk of impact related failure of a tank can be reduced from almost 39% for an unprotected tank facing in flight direction to below 0.1% for a tank protected by a properly designed Whipple shield.     

The future role of relay satellites for orbital telerobotics

Orbital robotics focuses on a variety of applications, as e.g. inspection and repair activities, spacecraft construction or orbit corrections. On-Orbit Servicing (OOS) activities have to be closely monitored by operators on ground. A direct contact to the spacecraft in Low Earth Orbit (LEO) is limiting the operational time of the robotic application. Therefore, geostationary satellites are desirable to relay the OOS signals and extend the servicing time window. A geostationary satellite in the communication chain not only introduces additional boundary conditions to the mission but also increases the time delay in the system. The latter is not very critical if the servicer satellite is operating autonomously. However, if the servicer is operating in a supervised control regime with a human in the loop, the increased time delay will have an impact on the operator’s task performance.     

Measuring tidal deformations at Europa’s surface

Key information on Europa’s interior can be gained by monitoring tidally-induced surface deformations from orbiting and landed spacecraft. Such observations would provide constraints on the thickness and rheology of Europa’s ice and liquid water layer, being thus an important tool to characterize basic physical properties of the satellite’s putative subsurface water ocean. Focusing on the outer ice-I layer we will present relations between the interior of Europa and key tidal parameters that can be retrieved from an instrument suite monitoring tidally-induced changes of local gravity, tilt, latitude and strain at the surface. A most promising approach would involve laser altimetry and gravitational field observations from an orbiting spacecraft combined with monitoring of tidally-induced gravity and tilt changes at the surface. However, tidal measurements at the surface may be significantly impeded by instrumental drift, instrument coupling to the surface, local sources of noise and the presumably short life-time of the instruments due to the harsh radiation environment.     

Planetary penetrators: Their origins,history and future

Penetrators, which emplace scientific instrumentation by high-speed impact into a planetary surface, have been advocated as an alternative to soft-landers for some four decades. However, such vehicles have yet to fly successfully. This paper reviews in detail, the origins of penetrators in the military arena, and the various planetary penetrator mission concepts that have been proposed, built and flown. From the very limited data available, penetrator developments alone (without delivery to the planet) have required ∼$30M: extensive analytical instrumentation may easily double this. Because the success of emplacement and operation depends inevitably on uncontrollable aspects of the target environment, unattractive failure probabilities for individual vehicles must be tolerated that are higher than the typical ‘3-sigma’ (99.5%) values typical for spacecraft. The two pathways to programmatic success, neither of which are likely in an austere financial environment, are a lucky flight as a ‘piggyback’ mission or technology demonstration, or with a substantial and unprecedented investment to launch a scientific (e.g. seismic) network mission with a large number of vehicles such that a number of terrain-induced failures can be tolerated.     

Prediction and evaluation of solar particle events based on precursor information.

Protection from the radiation effects of solar particle events for deep space mission crews requires a warning system to observe solar flares and predict subsequent charged particle fluxes. Such a system relates precursor information observed in each flare to the intensity, delay, and duration of the subsequent Solar Particle Event (SPE) at other locations in the solar system. A warning system of this type is now in operation at the NOAA Space Environment Services Center in Boulder, Colorado for support of space missions. It has been used to predict flare particle fluxes at the earth for flares of Solar Cycle 22. The flare parameters used and the effectiveness of the current warning system, based on Solar Cycle 22 experience, are presented, with an examination of the shortcomings. Needed improvements to the system include more complete observations of solar activity, especially information on the occurrences of solar mass ejections; and consideration of the effects of propagation conditions in the solar corona and interplanetary medium. Requirements for solar observations and forecasting systems on board the spacecraft are discussed.     

Alternative transfer to the Earth–Moon Lagrangian points L4 and L5 using lunar gravity assist

Lagrangian points L4 and L5 lie at 60° ahead of and behind the Moon in its orbit with respect to the Earth. Each one of them is a third point of an equilateral triangle with the base of the line defined by those two bodies. These Lagrangian points are stable for the Earth–Moon mass ratio. As so, these Lagrangian points represent remarkable positions to host astronomical observatories or space stations. However, this same distance characteristic may be a challenge for periodic servicing mission. This paper studies elliptic trajectories from an Earth circular parking orbit to reach the Moon’s sphere of influence and apply a swing-by maneuver in order to re-direct the path of a spacecraft to a vicinity of the Lagrangian points L4 and L5. Once the geocentric transfer orbit and the initial impulsive thrust have been determined, the goal is to establish the angle at which the geocentric trajectory crosses the lunar sphere of influence in such a way that when the spacecraft leaves the Moon’s gravitational field, its trajectory and velocity with respect to the Earth change in order to the spacecraft arrives at L4 and L5. In this work, the planar Circular Restricted Three Body Problem approximation is used and in order to avoid solving a two boundary problem, the patched-conic approximation is considered.     

Orbit determination by genetic algorithm and application to GEO observation

This paper demonstrates an initial orbit determination method that solves the problem by a genetic algorithm using two well-known solutions for the Lambert’s problem: universal variable method and Battin method. This paper also suggests an intuitive error evaluation method in terms of rotational angle and orbit shape by separating orbit elements into two groups. As reference orbit, mean orbit elements (original two-lines elements) and osculating orbit elements considering the J2 effect are adopted and compared. Our proposed orbit determination method has been tested with actual optical observations of a geosynchronous spacecraft. It should be noted that this demonstration of the orbit determination is limited to one test case. This observation was conducted during approximately 70 min on 2013/05/15 UT. Our method was compared with the orbit elements propagated by SGP4 using the TLE of the spacecraft. The result indicates that our proposed method had a slightly better performance on estimating orbit shape than Gauss’s methods and Escobal’s method by 120 km. In addition, the result of the rotational angle is closer to the osculating orbit elements than the mean orbit elements by 0.02°, which supports that the estimated orbit is valid.     

CubeSail: A low cost CubeSat based solar sail demonstration mission

CubeSail is a nano-solar sail mission based on the 3U CubeSat standard, which is currently being designed and built at the Surrey Space Centre, University of Surrey. CubeSail will have a total mass of around 3 kg and will deploy a 5 × 5 m sail in low Earth orbit. The primary aim of the mission is to demonstrate the concept of solar sailing and end-of-life de-orbiting using the sail membrane as a drag-sail. The spacecraft will have a compact 3-axis stabilised attitude control system, which uses three magnetic torquers aligned with the spacecraft principle axis as well as a novel two-dimensional translation stage separating the spacecraft bus from the sail. CubeSail’s deployment mechanism consists of four novel booms and four-quadrant sail membranes. The proposed booms are made from tape-spring blades and will deploy the sail membrane from a 2U CubeSat standard structure. This paper presents a systems level overview of the CubeSat mission, focusing on the mission orbit and de-orbiting, in addition to the deployment, attitude control and the satellite bus.     

Optimal spacecraft formation establishment and reconfiguration propelled by the geomagnetic Lorentz force

The Lorentz force acting on an electrostatically charged spacecraft as it moves through the planetary magnetic field could be utilized as propellantless electromagnetic propulsion for orbital maneuvering, such as spacecraft formation establishment and formation reconfiguration. By assuming that the Earth’s magnetic field could be modeled as a tilted dipole located at the center of Earth that corotates with Earth, a dynamical model that describes the relative orbital motion of Lorentz spacecraft is developed. Based on the proposed dynamical model, the energy-optimal open-loop trajectories of control inputs, namely, the required specific charges of Lorentz spacecraft, for Lorentz-propelled spacecraft formation establishment or reconfiguration problems with both fixed and free final conditions constraints are derived via Gauss pseudospectral method. The effect of the magnetic dipole tilt angle on the optimal control inputs and the relative transfer trajectories for formation establishment or reconfiguration is also investigated by comparisons with the results derived from a nontilted dipole model. Furthermore, a closed-loop integral sliding mode controller is designed to guarantee the trajectory tracking in the presence of external disturbances and modeling errors. The stability of the closed-loop system is proved by a Lyapunov-based approach. Numerical simulations are presented to verify the validity of the proposed open-loop control methods and demonstrate the performance of the closed-loop controller. Also, the results indicate the dipole tilt angle should be considered when designing control strategies for Lorentz-propelled spacecraft formation establishment or reconfiguration.     

ASTEX: An in situ exploration mission to two near-Earth asteroids

ASTEX (ASTeroid EXplorer) is a concept study of an in situ exploration mission to two Near-Earth-Asteroids (NEAs), which consists of an orbiting element and two individual lander units. The target candidates have different mineralogical compositions, i.e. one asteroid is chosen to be of “primitive’’ nature, the other to be a fragment of a differentiated asteroid. The main scientific goals of the ASTEX mission are the exploration of the physical, geological, and mineralogical nature of the NEAs. The higher level goal is the provision of information and constraints on the formation and evolution of our planetary system. The study identified realistic mission scenarios, defined the strawman payload as well as the requirements and options for the spacecraft bus including the propulsion system, the landers, the launcher, and assessed and defined the requirements for the mission’s operational ground segment.     

An introduction to the lunar and planetary science activities in Korea

Korea is planning a series of lunar space programs in 2020 starting with a lunar orbiter and a lander with a rover. Compared to other countries, Korea has a relatively brief history in space and planetary sciences. With the expected Korean missions on the near-term horizon and the relatively few Korean planetary scientists, Korea Institute of Geoscience and Mineral Resources (KIGAM) has established a new planetary research group focusing on development of prospective lunar instruments, analysis of the publicly available planetary data of the Moon, organizing nationwide planetary workshops, and initiating planetary educational programs with academic institutions. Korea has also initiated its own rocket development program, which could acquire a rocket-launch capability toward the Korean lunar mission. For the prospective Korea’s lunar science program, feasibility studies for some candidate science payloads have been started since 2010 for an orbiter and a lander. The concept design of each candidate instrument has been accomplished in 2012. It is expected that the development of science payloads may start by 2014 as Phase A. Not only developing hardware required for the lunar mission but also educational activities for young students are high priorities for Korea. The new plan of the Korean lunar mission can be successfully accomplished with international cooperative outreach programs in conjunction with internationally accessible planetary data system (PDS). This paper introduces the KIGAM’s international cooperative planetary research and educational programs and also summarizes other nationwide new developments for Korean lunar research projects at Kyung Hee University and Hanyang University.     

Systems design of a hybrid sail pole-sitter

This paper presents the preliminary systems design of a pole-sitter. This is a spacecraft that hovers over an Earth pole, creating a platform for full hemispheric observation of the polar regions, as well as direct-link telecommunications. To provide the necessary thrust, a hybrid propulsion system combines a solar sail with a more mature solar electric propulsion (SEP) thruster. Previous work by the authors showed that the combination of the two allows lower propellant mass fractions, at the cost of increased system complexity. This paper compares the pure SEP spacecraft with the hybrid spacecraft in terms of the launch mass necessary to deliver a certain payload for a given mission duration. A mass budget is proposed, and the conditions investigated under which the hybrid sail saves on the initial spacecraft initial mass. It is found that the hybrid spacecraft with near- to mid-term sail technology has a lower initial mass than the SEP case if the mission duration is 7 years or more, with greater benefits for longer duration missions. The hybrid spacecraft with far-term sail technology outperforms the pure SEP case even for short missions.     

Detection and monitoring of earthquake precursors: TwinSat,a Russia–UK satellite project

There is now a body of evidence to indicate that coupling occurs between the lithosphere–atmosphere–ionosphere prior to earthquake events. Nevertheless the physics of these phenomena and the possibilities of their use as part of an earthquake early warning system remain poorly understood. Proposed here is a programme to create a much greater understanding in this area through the deployment of a dedicated space asset along with coordinated ground stations, modelling and the creation of a highly accessible database. The space element would comprise 2 co-orbiting spacecraft (TwinSat) involving a microsatellite and a nanosatellite, each including a suite of science instruments appropriate to this study. Over a mission duration of 3 years ∼ 400 earthquakes in the range 6–6.9 on the Richter scale would be ‘observed’. Such a programme is a prerequisite for an effective earthquake early warning system.     

Testing Modified Newtonian Dynamics with LISA Pathfinder

We suggest that LISA Pathfinder, a technology demonstrator for the future gravitational wave observatory LISA, could be used to carry out a direct experimental test of Modified Newtonian Dynamics (MOND). The LISA Pathfinder spacecraft is currently being built and the launch date is just a few years away. No modifications of the spacecraft are required, nor any interference with its nominal mission. The basic concept is to fly LISA Pathfinder through the region around the Sun-Earth saddle point, in an extended mission phase, once the original mission goals are achieved. We examine various strategies to reach the saddle point, and find that the preferred strategy, yielding relatively short transfer times of just over 1 year, probably involves a lunar fly-by. LISA Pathfinder will be able to probe the intermediate MOND regime, i.e. the transition between deep MOND and Newtonian gravity. We present robust estimates of the anomalous gravity gradients that LISA Pathfinder should be exposed to, based on MONDian effects as derived from the Tensor-Vector-Scalar (TeVeS) theory. The spacecraft speed and spatial scale of the MOND signal combine in a way that the spectral signature of the signal falls precisely into LISA Pathfinder’s measurement bandwidth. We find that if the gravity gradiometer on-board the spacecraft achieves its currently predicted sensitivity, these anomalous gradients could not just be detected, but measured in some detail.     

基于有限状态机的操作系统需求层形式化验证

操作系统是航天器必备的基本软件，操作系统的可靠性和安全性直接关系航天型号任务的成败.虽然目前已采用多种手段对操作系统进行可靠性和安全性保障，但仍存在不能完全排除缺陷的情况，因此对空间操作系统开展形式化验证研究势在必行.需求层验证是操作系统形式化验证的一部分，本文在分析操作系统需求的基础上，采用有限状态机在操作系统需求层进行形式化描述，并针对应用在某航天器上的SpaceOS2在需求层进行了建模，相应地在定理证明工具Coq中进行了描述建模；然后定义了六条操作系统应满足的全局性质并进行了形式化描述，给出了系统模型满足这些性质的机器可检查的证明.证明结果表明采用有限状态机方法对操作系统需求层进行形式化验证是可行的，为进一步全面形式化验证奠定了基础.     

Mars Phobos and Deimos Survey (M-PADS) – A martian Moons orbiter and Phobos lander

We describe a Mars ‘Micro Mission’ for detailed study of the martian satellites Phobos and Deimos. The mission involves two ∼330 kg spacecraft equipped with solar electric propulsion to reach Mars orbit. The two spacecraft are stacked for launch: an orbiter for remote investigation of the moons and in situ studies of their environment in Mars orbit, and another carrying a lander for in situ measurements on the surface of Phobos (or alternatively Deimos). Phobos and Deimos remain only partially studied, and Deimos less well than Phobos. Mars has almost always been the primary mission objective, while the more dedicated Phobos project (1988–89) failed to realise its full potential. Many questions remain concerning the moons’ origins, evolution, physical nature and composition. Current missions, such as Mars Express, are extending our knowledge of Phobos in some areas but largely neglect Deimos. The objectives of M-PADS focus on: origins and evolution, interactions with Mars, volatiles and interiors, surface features, and differences. The consequent measurement requirements imply both landed and remote sensing payloads. M-PADS is expected to accommodate a 60 kg orbital payload and a 16 kg lander payload. M-PADS resulted from a BNSC-funded study carried out in 2003 to define candidate Mars Micro Mission concepts for ESA’s Aurora programme.     

An in situ laser induced breakdown spectroscope (LIBS) for Chandrayaan-2 rover: Ablation kinetics and emissivity estimations

A miniaturized in situ laser induced breakdown spectroscope-LIBS is one of the two lunar rover payloads to be flown in India’s next lunar mission Chandrayaan-2, with an objective to carry-out a precise qualitative and quantitative elemental analyses of lunar regolith at the proximity of the landing region. As per the imposed mission constraints and the executed design optimization studies, a compact and light-weight LIBS prototype model is developed at our premises. This paper mainly concerns with the estimation of theoretical aspects; especially on evaluation of elemental ablation parameters and signal-to-noise ratio (SNR) calculations for the designed instrument. Theoretical estimations and simulations yielded an incident laser power density of the order of 5 × 10¹⁰ W/cm² on the target surface at a defined lens-to-surface distance (LTSD) of 200 mm and revealed an SNR > 100 for most of the elements under consideration. This paper also addresses the impact of LTSD variation on detection capability. The estimation of plasma-temperatures was carried out utilizing the emission spectra obtained under high vacuum environments employing the LIBS laboratory model. Experimental investigations and the performed theoretical estimations asserted the successful operation of the configured LIBS instrument for in situ elemental analyses on lunar surface.