Hubble Space Telescope at twelve years of age

The Hubble Space Telescope was deployed from the Space Shuttle Discovery into a 380-mile high Earth orbit on April 25, 1990. It subsequently made outstanding astronomical discoveries with its 8-foot (2.4-meter) telescope and other scientific instruments. Critical to the successful observations was continuous availability of power from its solar arrays during sunlit periods, and from nickel-hydrogen batteries when the satellite was in the Earth's shadow. The adopted nickel-hydrogen batteries were carefully selected and tested to confirm their depth-of-discharge and operating temperature that delivered the longest life in charge/discharge cycling service. These batteries had a design life of 7 years. At 12 years after launch the Hubble batteries have delivered more charge/discharge cycles than any other batteries in low-Earth orbit. However, the Hubble batteries have been subjected to many unexpected stresses, and peculiar reductions in battery capacity have been observed. Battery replacement requires a costly trip to the Hubble Space Telescope by astronauts, so the remaining useful life of the batteries must be predicted. Already in four servicing missions, astronauts have replaced or modified optics, solar arrays, a power control unit, and various science packages. A fifth servicing mission is scheduled in 2004. This paper discusses battery charging hardware and software controls, history of battery events in Hubble, cell performance model and spare battery tests, and capacity walkdown.     

A microcontroller-based intelligent battery system

State-of-charge indication for a secondary battery is becoming increasingly important for battery-operated electronics. Consumers are demanding fast charging times, increased battery lifetime, and fuel gauge capabilities. All of these demands require that the state of charge within a battery be known. One of the simplest methods employed to determine state of charge is to monitor the voltage of the battery. However, this method alone is not a good indicator of battery energy, since both NiMH and NiCd batteries have voltage-versus-energy curves that are essentially flat. This paper presents a more effective method of determining the state of charge in secondary cell batteries. A NiMH battery is used as our test vehicle, since it is one of the more difficult batteries to determine state of charge. This method monitors the battery's temperature, voltage, and discharge/charge rate. A microcontroller then manipulates the information, using look-up tables to determine the state of charge. Also, by modifying the look-up tables, this technique can be employed in many other battery technologies and is not limited to NiMH     

Bipolar nickel-metal hydride batteries for aerospace applications

Electro Energy Inc. (EEI) is developing high power, long life, bipolar nickel-metal hydride batteries for aerospace applications. Bipolar nickel-metal hydride designs allow for high energy and high power designs with a 25 percent reduction in both weight and volume as compared to prismatic and/or cylindrical Ni-MH designs. Utilizing a sealed wafer cell design EEI has demonstrated a 1.2 kW/kg power capability. Prototype designs have achieved 70 Wh/kg. Designs studies show 80 Wh/kg are achievable with EEI's state-of-the-art technology. The sealed wafer cell is the building block for EEI's high power and high voltage bipolar batteries making the assembly easy and significantly lower in cost. Satellite and aircraft batteries are being developed which provide high power and long life. Sealed cells now show excellent rate capability and life. Cells tested in a low earth orbit (LEO) cycle have reached 9000 cycles and continue on test. High power, bipolar battery designs are ideal in applications where using conventional aerospace battery technology would require excessive capacity; weight and volume, thereby reducing usable payload on the vehicle     

Advanced lithium ion battery charger

A lithium ion battery charger has been developed for four and eight cell batteries or multiples thereof. This charger has the advantage over those using commercial lithium ion charging chips in that the individual cells are allowed to be taper charged at their upper charging voltage rather than be cutoff when all cells of the string have reached the upper charging voltage limit. Since 30-60% of the capacity of lithium ion cells may be restored during the taper charge, this charger has a distinct benefit of fully charging lithium ion batteries by restoring all of the available capacity to all of its cells     

Stochastic battery discharge in portable communication devices

The objective of this work is to explore ways in which performance of battery systems can be enhanced through the use of energy-efficient battery management techniques. The phenomenon of charge recovery that takes place under pulsed discharge conditions is identified as a mechanism that can be exploited to enhance the capacity of a cell in a portable communication device. The bursty nature of many data traffic sources suggests that data transmissions in communication devices may provide natural opportunities for charge recovery. We model the data source as a stochastic process and let the cell discharge be driven by such a process. We use a model of a dual lithium ion insertion cell to identify the improvement to cell capacity that results from the stochastic discharge. The insight from this study leads us to propose discharge shaping techniques that tradeoff energy efficiency with delay in the required current supply     

Performance characteristics of lithium-ion cells for NASA's Mars2001 Lander application

NASA requires lightweight rechargeable batteries for future missions to Mars and the outer planets that are capable of operating over a wide range of temperatures, with high specific energy and energy densities. Due to the attractive performance characteristics, lithium-ion batteries have been identified as the battery chemistry of choice for a number of future applications, including Mars rovers and landers. The Mars 2001 Lander (Mars Surveyor Program MSP 01) will be one of the first missions which will utilize lithium-ion technology. This application will require two lithium-ion batteries, each being 28 V (eight cells), 25 Ah and 8 kg. In addition to the requirement of being able to supply at least 200 cycles and 90 days of operation on the surface of Mars, the battery must be capable of operation (both charge and discharge) at temperatures as low as -20°C. To assess the viability of lithium-ion cells for these applications, a number of performance characterization tests have been performed, including: assessing the room temperature cycle life, low temperature cycle life (-20°C), rate capability as a function of temperature, pulse capability, self-discharge and storage characteristics, as well as mission profile capability. This paper describes the Mars 2001 Lander mission battery requirements and contains results of the cell testing conducted to-date in support of the mission,     

Spacecraft energy storage systems

Flywheel Energy Storage Systems represent an exciting alternative to traditional battery storage systems used to power satellites during periods of eclipse. The increasing demand for reliable communication and data access is driving explosive growth in the number of satellite systems being developed as well as their performance requirements. Power-on orbit is the key to this performance, and batteries are becoming increasingly unattractive as an energy storage media. Flywheel systems offer very attractive characteristics for both energy storage, in terms of energy density and the number of charge/discharge cycles, and the important side benefit of spacecraft attitude control     

Nickel-Cadmium Batteries as Capacitive Filters for Pulsed Loads

This investigation consisted of several tests of specially fabricated nickel-cadmium batteries having circular disk-type electrodes. These batteries were evaluated as filter elements between a constant current power supply and a 5 Hz pulsed load demanding approximately twice the power supply current during the load on a portion of the cycle. Short tests lasting 104 cycles were conducted at up to a 21 C rate and an equivalent energy density of over 40 J/Ib. In addition, two batteries were subjected to 10h dischar cycles, one at a 6.5 C rate and the other at a 13 C rate. Assuming an electrode-to-battery weight ratio of 0.5, these tests represent an energy density of about 7 and 14 J/Ib, respectively. Energy density, efficiency, capacitance, average voltage, and available capacity were tracked during these tests. After 10y capacity degradation was negligible for one battery and about 20 percent for the other. Cadmium electrode failure may be the factor limiting lifetime at extremely low depth of discharge cycling. The output was examined and a simple equivalent circuit was proposed.     

基于直流微电网的混合储能协调控制策略仿真研究

针对直流微电网中光伏发电单元出力的波动性和间歇性造成系统内部功率不平衡的问题,混合储能系统可以同时发挥蓄电池高能量密度和超级电容高功率密度的优势,根据直流母线电压进行混合储能单元间的协调控制策略。该策略将直流母线电压进行分层控制,采用四个电压阈值共分成五个控制区域,以直流母线电压为信息载体,决定储能系统的运行状态,实现对混合储能单元的充电、放电模式间自主切换。电压分层控制有效地避免了蓄电池由于电压波动而频繁进行充放电切换,从而延长了电池的使用寿命。最后,MATLAB/Simulink的仿真结果验证了所提控制策略的可行性。     

Aerospace lithium solid polymer batteries

Lockheed Martin Missiles and Space and Ultralife Batteries, Inc. are developing batteries for spacecraft and launchers based on Li-ion solid-polymer-electrolyte cell technology. These cells utilize a carbon anode, a manganese dioxide cathode and a solid polymer electrolyte. Electrode and electrolyte layers are thin and flexible. The electrode assembly is easily fabricated into thin, flat prismatic shapes using ordinary lamination techniques and is hermetically sealed in thin foil packaging. Cells ranging in capacity from 4 Ah to 50 Ah have been designed and are in development testing. The packaged cells have specific energies in excess of 100 Wh/kg. Prototype 30 volt batteries have also been designed and are being assembled and tested along with the critical battery cell charge management controllers needed to recharge all cells to full capacity while preventing overvoltage damage. The major results of this development effort are reviewed and the key issues for advancing this technology to flight qualification demonstrations are discussed     

Thin-film Li-LiMn2O4 batteries

Thin-film rechargeable Li-LiMn₂O₄ batteries have been fabricated and characterized. Following deposition by electron beam evaporation of LiMn₂O₄, the amorphous as-deposited cathode films 1 cm² in area by 0.3to 4-μm thick were annealed at 700°C to 800°C in oxygen in order to form the crystalline spinet phase. The specific capacity of the cells between 4.5 V to 3.8 V ranged from 50 μAh/mg to 120 μAh/mg. When cycled over this range, the batteries exhibited excellent secondary performance with capacity losses as low as 0.001% per cycle. On charging to 5.3 V, a plateau with a median voltage of 5.1 V was observed. The total charge extracted between 3.8 V to 5.3 V corresponded to about 1 Li/Mn₂ O₄     

Life cycle testing of a sealed 24-V, 42-Ah nickel-cadmium aircraftbattery

Extensive research has been conducted in the design and manufacture of very long life sealed maintenance free nickel-cadmium aircraft batteries. This study presents data on a 100% depth of discharge (DOD) life test performed on a nominal capacity 42-Ah battery. The purpose of this study is to validate design concepts, determine the life characteristics of the newly designed sealed Ni-Cd batteries, and develop baseline information on failure rates and mechanisms. The data from this experiment can be used to compare depth of discharge versus battery life with similar tests such as the lower DOD experiments performed on spacecraft batteries. This information is important in the ongoing development of long life batteries and in developing failure models for life prediction     

Nickel-hydrogen multicell common pressure vessel batterydevelopment update

Flight qualification of the multicell common pressure vessel (CPV) nickel-hydrogen (Ni-H₂) battery is discussed. The battery has completed full flight qualification, including random vibration at 19.5 g for two minutes in each axis, electrical characterization in a thermal vacuum chamber, and mass-spectroscopy vessel leak detection. A first launch is scheduled in 1992. Several design variations, ranging from 9 Ah to 125 Ah and 12 to 32 V, have been developed and prototypes fabricated. Designs for smaller capacity, smaller diameter (6.4-8.9 cm), and higher voltage (up to 100 V) are in progress. The CPV battery offers cost and weight savings of up to 30% as compared to traditional nickel-cadmium (Ni-Cd) and individual pressure vessel (IPV) Ni-H₂ batteries. The fully qualified design provided a 50% weight savings over its Nd-Cd predecessor for the same application. Its reduced volume also provides a significant advantage over IPV technology. Resistance data show a further advantage     

Aerospace and military battery applications

This paper gives a review of the papers presented at the IEEE 17th Annual Battery Conference on Applications and Advances, Long Beach, CA, USA, 2002. The topics covered are: Li batteries for satellites, capacity fade of Li-ion cells cycled at different temperatures, Ni-H/sub 2/ battery lifetime, batteries for Mars-exploring vehicles, Li-ion cell performance enhancement at low temperatures, navy service batteries, and US Army man portable applications and mobile power challenges.     

High reliability lithium rechargeable batteries for specialties

Since their development in the late 1980s, lithium rechargeable batteries have enjoyed rapid growth and wide use as a commodity battery known for its higher energy density storage and lightweight convenience. These same attributes are emerging as a strong platform in power source development for the medical and aerospace sectors with highly customized applications and narrowly defined criteria. Accordingly, this new generation of lithium rechargeables must be hermetically sealed, have long-term storage capability, and zero-fault tolerances for common causes of field failures such as electrolyte leakage or short circuits from mechanical deformation. Quallion has been developing and manufacturing highly reliable lithium rechargeable cells for medical, aerospace, and specialty applications. Summarized in this paper are some key technologies developed at Quallion for designing and manufacturing of this new class of lithium rechargeable batteries. They include: 1) leakage reliability; 2) self-extinguishing electrolyte system; 3) mechanical impact resistance; 4) deep discharge storage; and 5) high reliability manufacturing.     

Fast equalization for large lithium ion batteries

Slight differences between the series connected cells in a lithium ion (Lilon) battery pack can produce imbalances in the cell voltages, and this greatly reduces the charge capacity. These batteries cannot be trickle-charged like a lead acid battery since this would slightly overcharge some cells and may cause these cells to ignite. Therefore, an electronic equalizer (EQU) should be used to balance the cell voltages individually. The targeted EQU described herein can be connected to any cell via a set of sealed relays to provide much faster equalization and higher efficiency than previous methods.     

Electric-vehicle batteries

Electric vehicles that can't reach trolley wires need batteries. In the early 1900's electric cars disappeared when owners found that replacing the car's worn-out lead-acid battery costs more than a new gasoline-powered car. Most of today's electric cars are still propelled by lead-acid batteries. General Motors in their prototype Impact, for example, used starting-lighting-ignition batteries, which deliver lots of power for demonstrations, but have a life of less than 100 deep discharges. Now promising alternative technology has challenged the world-wide lead miners, refiners, and battery makers into forming a consortium that sponsors research into making better lead-acid batteries. Horizon's new bipolar battery delivered 50 watt-hours per kg (Wh/kg), compared with 20 for ordinary transport-vehicle batteries. The alternatives are delivering from 80 Wh/kg (nickel-metal hydride) up to 200 Wh/kg (zinc-bromine). A Fiat Panda traveled 260 km on a single charge of its zinc-bromine battery. A German 3.5-ton postal truck traveled 300 km with a single charge in its 650-kg (146 Wh/kg) zinc-air battery. Its top speed was 110 km per hour     

Behavior of a cycled Ni-Cd battery during pulse discharge

The pulse discharge behavior of a 9-Ah, 6-V nickel-cadmium (Ni-Cd) battery fabricated for the FAST program was studied. The response of the battery voltage to a pulse with a current of 60 A and duration of 10 to 200 ms was measured, along with the capacity remaining at the end of pulse discharge. The maximum drop in voltage at the beginning of the pulse was 505 to 1,049 mV, and battery capacity remained stable     

Advanced materials for next generation NiMH portable, HEV and EVbatteries

While Ovonic NiMH batteries are already in high volume commercial production for portable applications, advances in materials technology have enabled performance improvements in specific energy (100 Wh/kg), specific power (600-1000 W/kg), high temperature operation, charge retention, and voltage stability. Concurrent with technology advances, Ovonic NiMH batteries have established performance and commercial milestones in electric vehicles, hybrid electric vehicles, as well as scooter, motorcycle and bicycle applications. As important as these advances, significant manufacturing cost reductions have also occurred which allow continued growth of NiMH technology. In this paper, advances in performance, applications and cost reduction are discussed with particular emphasis on the improved proprietary metal hydride and nickel hydroxide materials that make such advances possible     

The Hy-StorTM battery

The Hy-Stor^TM Battery is a rechargeable battery being developed for electric vehicles and other large battery applications. The battery combines the high energy storage capability of metal hydride alloys with the high cycle life and discharge rate capabilities of nickel-hydrogen cells. It is a hybrid battery concept that offers potential performance, economic and safety advantages over other large battery technologies. Very recent developments indicate that much smaller batteries can also be produced to meet the needs of the portable computer and other portable electronic device markets. Initial tests demonstrated the ability of a metal hydride storage system to achieve high cycle life when absorbing hydrogen that was saturated with battery electrolyte solution and then passed through a purifier. Based on positive test results, a patent for the Hy-Stor battery was applied for and granted