压电智能结构传感器/作动器位置优化研究

研究压电主动结构振动控制当中传感器／作动器的位置优化问题。从系统的状态空间方程出发，在系统可控性、可观性Grammian矩阵特征值的基础上来描述性能指标，以控制能量最小化和传感能量最大化作为优化目标，利用遗传算法（GE）进行优化计算，计算过程中对传感器／作动器的位置采用二进制编码加以描述。通过对一压电板结构的仿真计算对该方法进行了验证，优化计算结果与枚举法结果完全相符，从而证明了方法的有效性。     

采用共位配置的分布式压电敏感器和致动器的挠性结构振动控制

研究采用共位配置的分布式压电敏感器和致动器的挠性悬臂梁的振动控制问题，其中敏感器由压电聚乙二烯氟化物薄膜（PVDF）制成，致动器由压电陶瓷（PZT）或PVDF制成。本文首先建立系统的模型，设计了一种线性反馈控制方案，并应用无穷维空间的LaSalle不变原理，证明了相应闭环系统的渐近稳定性。     

基于特征模型的挠性悬臂板控制

针对航天器上太阳帆板这种悬臂外伸薄板结构的挠性附件 ,存在环境扰动下所引起的振动 ,本文采用压电智能结构作为执行器对悬臂板进行主动振动控制。基于板系统的特征建模 ,并结合自适应控制对挠性板的主动控制进行了研究。通过仿真研究结果与应变律反馈控制比较 ,表明该方法的有效性     

压电纤维复合材料的研究

以提高交叉指形电极压电纤维复合材料诱导应变和挟持应力为目的,采用有限元软件ANSYS分析了电极区聚合物参数、交叉指型电极结构和压电相体积分数对压电纤维复合材料诱导应变和挟持应力的影响。结果表明：增加电极区聚合物的介电常数或减小电极区聚合物的厚度,能够提高元件的诱导应变和挟持应力,元件诱导应变最大可达173με;减小分支电极的周期或者适当增大分支电极的宽度,可以有效地提高元件的作动性能;提高压电纤维体积分数,有利于提高元件的作动性能。     

多维驱动微型振动平台的研制

一种以压电元件为驱动源,结合柔性铰链机构的微型振动平台,通过计算机设计控制电压波形,对其进行三维振动控制.通过实验证明,该机构具有良好的波形跟踪性能,易于实现复杂控制波形,适用于微型机械的动态性能测试.     

压电致动器扑翼结构动力学仿真

采用传统扑动机构的微型扑翼,气动效率低、扑动能耗大。采用压电致动器的微型扑翼通过压电材料进行致动使机翼产生上下扑动,有效地将扑动机构和机翼两个主要系统进行集成,不仅节省重量,同时它具有任务变形自适应能力强、气动效率高和扑动能耗小的特点。通过PCL语言建立采用压电致动器的扑翼有限元模型,结合同尺寸扑翼气动力试验数据,进行采用压电致动器扑翼结构仿真。利用仿真结果研制采用压电致动器扑翼原理样机,研究表明,采用压电致动器后扑翼扑动频率得到明显提高,压电片可有效控制机翼的弯扭变形,有助于提高扑翼的气动效率。     

Hypervelocity impact induced shock acoustic emission waves for quantitative damage evaluation using in situ miniaturized piezoelectric sensor network

Manmade debris and natural meteoroids, travelling in the Low Earth Orbit at a speed of several kilometers per second, pose a severe safety concern to the spacecraft in service through the HyperVelocity Impact(HVI). To address this issue, an investigation of shock Acoustic Emission(AE) waves induced by HVI to a downscaled two-layer Whipple shielding structure is performed,to realize a quantitative damage evaluation. Firstly a hybrid numerical model integrating smoothparticle hydrodynamics and finite element is built to obtain the wave response. The projectiles, with various impact velocities and directions, are modelled to impact the shielding structure with different thicknesses. Then experimental validation is carried out with built-in miniaturized piezoelectric sensors to in situ sense the HVI-induced AE waves. A quantitative agreement is obtained between numerical and experimental results, demonstrating the correctness of the hybrid model and facilitating the explanation of obtained AE signals in experiment. Based on the understanding of HVI-induced wave components, assessment of the damage severity, i.e., whether the outer shielding layer is perforated or not, is performed using the energy ratio between the regions of ‘‘high frequency" and ‘‘low frequency" in the acquired AE signals. Lastly, the direct-arrival fundamentalsymmetric wave mode is isolated from each sensing signal to be input into an enhanced delay-andsum algorithm, which visualizes HVI spots accurately and instantaneously with different sensor network configuration. All these works demonstrate the potential of quantitative, in situ, and real time HVI monitoring using miniaturized piezoelectric sensor network.     

Sound insulation performance of plates with interconnected distributed piezoelectric patches

This paper deals with the sound insulation performance of a thin plate with intercon-nected distributed piezoelectric patches. Piezoelectric patches are periodically bonded on the sur-faces of the plate in a collocated fashion, and are interconnected via an inductive circuit network. This piezoelectric system is termed as piezo-electromechanical (PEM) plate in the paper. Homogenization methods are involved under a sub-wavelength assumption to analytically develop the dynamical equations for the PEM plate. The dispersion relationships and energy densities of the wave modes propagating in the PEM plate are studied;the sub-wavelength assumption is verified for the simulations in this paper. The coincidence frequency of the PEM plate is researched, and results show that the coincidence frequency of the PEM plate will disappear at certain circum-stances;mathematical and physical explanations are made for this phenomenon. The disappearance of the coincidence frequency is used to optimize the value of inductance, for the purpose of improv-ing the sound transmission loss of the PEM plate.     

基于压电纤维复合材料的离心叶轮叶片高阶模态测量

为准确获取离心叶轮叶片的高阶振动特性及其模态,利用压电纤维复合材料(Marco fiber composite,MFC)对离心叶轮叶片进行模态测试。设计了MFC激励系统,提出了MFC选型、激励和测点位置的确定方法,研究了不同信号的高阶模态激励效果,并分析了MFC附加质量和刚度对叶片固有频率和模态的影响;结合有限元仿真结果,对比分析了前20阶振动模态的异同。试验结果表明:MFC具有操作简单、重复性好、信噪比高、能够稳定激励出高阶模态等优势,计算模态与测量模态吻合较好,在第6～8阶与第12～15阶之间存在模态密集区域;MFC附加质量和刚度对实验固有频率的影响低于4%。提出的MFC激励方法可用于具有较高固有频率的航空发动机部件的模态测量。     

航空航天智能材料与智能结构研究进展

智能材料作为新兴多功能材料,能够实现结构功能化、功能多样化。智能结构是在结构中集成智能材料作为传感器和驱动器,使结构除了具有承载、传力、连接等功能外,还具有自感知、自诊断、自驱动、自修复等能力,以更好地适应外界环境的变化,可显著提升航空航天架构的性能。目前智能材料与智能结构已成为航空航天架构减重增效研究的重点。根据国内外智能材料和结构的研究进展,综述了压电材料、铁磁材料、形状记忆材料、智能复合材料等智能材料的发展;讨论了智能结构的研究及应用前景,包括自诊断智能结构、自修复智能结构和减振降噪智能结构;最后,指出了智能材料与结构当前面临的一些挑战性问题,展望了其在航空航天领域的应用前景。