A multi-stage regulation strategy of space manipulators with a free-swinging joint failure

To ensure tasks can be completed after a free-swinging joint failure occurs, a multi-stage regulation strategy of space manipulators is proposed. Considering all terms of the dynamics equation, an evaluation model of the regulation ability (EMRA) of active joints over the fault joint is established based on the fuzzy entropy. And then a multi-stage regulation strategy based on the EMRA is designed to regulate the fault joint. The strategy divides the regulation process into several stages, and select a certain active joint to regulative the fault joint in every stage. With this multi-stage regulation strategy, the fault joint can be regulated to the desired angle without huge torque on regulative joints. The simulation is carried out with a 7-DOF space manipulator, verifying the correctness and effectiveness of the multi-stage regulation strategy. The strategy has three advantages: Coriolis and centrifugal terms are both considered for the first time in selecting the regulative joint, making the selection result more in line with the actual regulation process; The influence of the model uncertainty is eliminated in establishing the EMRA, making the evaluation of regulative ability more precise; The fault joint is successfully regulated to the desired angle without huge torque on regulative joints.     

FDI飞机舵面损伤故障全局检测的非线性数学模型

阐述了飞机在单舵面损伤故障下 ,建立故障状态下的数学模型 ,以及同样输入条件下飞机正常运动时的数学模型 ,得到飞机在相同飞行条件下损伤时的气动系数和无损伤正常时的气动系数 ,最终得到气动系数的残差。这将为以后飞机过载残差和角加速度残差奠定基础。论文中结合一定的算例给予证实推论的正确性。     

滑油量对恒速传动装置的影响

本文介绍了中外航空公司飞机发动机恒速传动装置几个故障典例及造成的危害,分析了填加滑油量不当对发动机恒速传动装置的影响,提出了预防措施。     

备件配置方法研究

针对电路板件故障数据记录的实际,运用可靠性理论,提出了没有故障数据板件的备件数量计算方法;对有故障统计数据的板件引用了经验模型来确定备件配置。     

拉格朗日中值定理的一个新证法

本文给出了利用坐标旋转法证明拉格朗日中值定理的一种新方法。即从罗尔定理出发，采用坐标旋转法及隐函数、复合函数求导法则，证明拉格朗日中值定理，由于该证明方法从直观的几何意义入手，因此，其证明过程更加清晰、易懂。     

Investigation of the differential rotation of the large-scale magnetic elements for the solar activity cycles 20 and 21

The differential rotation of the patterns of the large-scale solar magnetic field during solar activity cycles 20 and 21 is investigated. Compact magnetic elements with the polarity of the general solar magnetic field have larger speed of rotation than the elements with the opposite polarity. The surface of the Sun was divided by 10°-zones. In all of them the average rotation rate of the magnetic elements with negative polarity is little higher than that of the magnetic elements with positive polarity, except for 50°-zone of the south hemisphere and at the 10° latitude of the north hemisphere.

The rates of differential rotation for large-scale magnetic elements with negative and positive polarities have similar behavior for both cycles of the solar activity.

The rotation rate varies at polarity reversal of the circumpolar magnetic fields. For the cycle No 20 in 1969–1970 the threefold reversal took place in the northern hemisphere and variations of rotation rate can be noticed for magnetic elements both with positive and negative polarity for each 10°-zone in the same hemisphere.     

Modelling of Spall in an Anisotropic Aluminium Alloy

Spall caused by hypervelocity impacts at the lower range of velocities could result in significant damage to spacecraft. A number of polycrystalline alloys, used in spacecraft manufacturing, exhibit a pronounced anisotropy in their mechanical properties. The aluminium alloy AA 7010, whose orthotropy is a consequence of the meso-scale phase distribution or grain morphology, has been chosen for this investigation. The material failure observed in plate impact was simulated using a number of spall models. The Hugoniot elastic limit and spall strength have been studied as a function of orientation, and compared to experimental results.     

基于损伤力学的概率疲劳曲线获取方法

文章基于损伤力学方法获得满足疲劳试验的损伤演化方程,推导出一般条件下的理论疲劳曲线以及相对应的理论中值疲劳曲线与理论理想疲劳曲线；然后根据试验数据即可确定理论疲劳曲线中的参量,从而获取疲劳曲线计算公式。通过此计算公式,可以方便地得到一组以初始损伤为参数的疲劳曲线族,继而得到以失效概率为参数的疲劳曲线族,大大降低了所需试验的数量,并为结构抗疲劳设计和寿命估算提供了依据。     

提高电铸局部电沉积速率试验研究

电铸成型是采用离子沉积的方法制造复制件，具有很好的复制精度，因此电铸技术得到了广泛的应用。但由于受极限电流密度等多方面因素的影响，电铸速率一直是制约电铸技术发展的一个瓶颈，许多学者为此做了大量的理论和试验研究，但对如何提高极限电流密度还没有提供一个比较满意的答案，为提高电铸局部电沉积速率，本文在前人工作的基础上，讨论了影响电铸速率的因素，提出了一种新型的电铸方法－喷射式电铸，并通过两组试验分析了局部电沉积速率怀电铸液流量的关系以及局部铸速率与喷嘴口径的关系，试验结果表明，采用喷射式电铸可以大大提高局部极限电流密度，从而使电铸局部电沉积速率有一个较大范围的提高，为将电铸与快速成型结合奠定了试验基础。     

开关磁阻电动机的Fuzzy-PI控制

本文介绍了开关磁阻电动机低速时的斩波控制与高速时的单脉冲控制方案,论述了控制参数的优化选择范围及其变化对电机效率和转矩的影响,在分析了模糊控制,比例积分控制以及系统本身特点的基础上,提出了基于上述控制方案的Fuzzy-PI复合控制算法,并详细地讨论了这种算法在开关磁阻电机系统中的实现,采用的粗调、细调技术有效地解决了动态性能与稳态精度之间的矛盾。文章最后给出了在5.5kWSR132-8/6样机上的运行试验结果。试验表明:这种控制方法性能优良。