Multimodal characteristics of a piezoelectric lead zirconate titanate element impacted with iron particles having velocities above 20 km/s

The responses of a piezoelectric lead zirconate titanate (PZT) element to hypervelocity collisions were experimentally studied. In this study, the particles of masses ranging from 0.3 to 10 fg were made to collide with PZT at velocities between 20 and 96 km/s. The amplitude and the corresponding rise time of the single-pulse output signals that were produced in the piezoelectric PZT element were measured to determine the possible collision states. The results revealed an apparently multimodal output; three classes were assumed to be involved in the pulse formation mechanism. The amplitude and rise time were sensitive to the collision velocity. The multimodal behavior implied that the PZT-based cosmic dust detectors should be calibrated according to the class they belong to.     

Atmospheric response to a Hot SST Event in November 2006 as observed by the AIRS instrument

Using Atmospheric Infrared Sounder (AIRS) products of atmospheric temperature and geopotential height, we investigate the atmospheric response to HE0611, which was found and investigated by [Qin, H., Kawamura, H., Sakaida, F., Ando, K. A case study of the tropical Hot Event in November 2006 (HE0611) using a geostationary meteorological satellite and the TAO/TRITON mooring array. J. Geophys. Res. 113, C08045, doi: 10.1029/2007JC004640, 2008]. HE0611 was formed by connecting two very high SST areas, HE0611-East and HE0611-West. The period-mean atmosphere temperatures at levels of 925 and 850 hPa in HE0611-West are higher, by about 0.5 K, than those in WE0611-East while the atmospheric temperatures at middle to high levels (700–300 hPa) are higher in HE0611-East. The period-mean geopotential heights HE0611-East are much lower than those in HE0611-West for the levels from the surface to 400 hPa. The mean geopotential heights from 400 hPa to 200 hPa are higher in HE0611-East. In the middle and high layers over HE0611-West, the atmosphere temperatures gradually decrease from 7th to 17th, and then increase significantly. The increase in HE0611-East starts from 15th November, which is earlier than that of HE0611-West. The geopotential heights in the high layer of both the areas also show corresponding behaviors. The lagged atmospheric response in the western part is confirmed by the correlation analysis. It emerges that the atmospheric response to HE0611 is well organized and associated with deep convention in HE0611-East and subsidence in HE0611-West. These are also consistent with the HE0611 features and evolution revealed by earlier HE studies.     

AMF phasing—A precise control of the ignition timing of AKM for reduction of the injection error

This paper deals with a new concept, named “AMF Phasing”, which intends to minimize the effect of injection error that would result during apogee motor firing (AMF) of the spinning spacecraft. The characteristic of velocity increment error is derived analytically, based on the disturbed spinning motion during AMF. In order to precisely estimate the amount of fuel required for post-AMF orbital correction maneuvers, a probability model is proposed which estimates the total injection error probability combining the dominant error factors, i.e. pre-AMF attitude determination error and velocity increment error during AMF.It is shown that a substantial saving in fuel normally consumed for post-AMF can be expected, when the resultant velocity increment error contribution, which otherwise would be randomly directed in inertial space, is controlled so that it appears in the direction of local right ascension by igniting AKM at the proper instant (AMF Phasing). The procedure for AMF phasing, using a Sun pulse as a reference signal for the ignition timing is described in this paper. It was actually applied for GMS-2, Japan's second Geostationary Meteorological Satellite (HIMAWARI-II). The HIMAWARI-II post-AMF orbit determination shows that AMF Phasing worked successfully and it is concluded that a substantial fuel saving was achieved.     

The South Pole-Aitken basin region,Moon: GIS-based geologic investigation using Kaguya elemental information

Using Geographic Information Systems (GIS), we performed comparative analysis among stratigraphic information and the Kaguya (SELENE) GRS data of the ∼2500-km-diameter South Pole-Aitken (SPA) basin and its surroundings. Results indicate that the surface rock materials (including ancient crater materials, mare basalts, and possible SPA impact melt) are average to slightly elevated in K and Th with respect to the rest of the Moon. Also, this study demonstrates that K and Th have not significantly changed since the formation of SPA. The elemental signatures of the impact basin of Fe, Ti, Si, O through time include evidence for resurfacing by ejecta materials and late-stage volcanism. The oldest surfaces of SPA are found to be oxygen-depleted during the heavy bombardment period relative to later stages of geologic development, followed by both an increase in silicon and oxygen, possibly due to ejecta sourced from outside of SPA, and subsequent modification due to mare basaltic volcanism, which increased iron and titanium within SPA. The influence of the distinct geologic history of SPA and surroundings on the mineralogic and elemental abundances is evident as shown in our investigation.     

复合材料界面模态混合度研究

综述了消除复合材料界面裂纹应力奇异性及求解界面模态混合度的主要方法,分析讨论了各个方法的优缺点.通过分析讨论发现:模态混合度表征界面力学性能可以准确地描述界面裂纹尖端处各应变能释放率分量的振荡特性;求解与裂纹扩展长度无关的各应变能释放率分量及模态混合度是研究复合材料界面裂纹问题的难点;采用混合模态界面力学性能试验方法验证基于正则化长度等求解模态混合度方法的有效性,进而准确预测复合材料分层的发生及扩展是今后研究复合材料界面力学问题的发展方向.     

Mercury Dust Monitor (MDM) Onboard the Mio Orbiter of the BepiColombo Mission

Space Science Reviews - In this chapter, we review the contribution of space missions to the determination of the elemental and isotopic composition of Earth, Moon and the terrestrial planets, with...     

Analytical expression for distant retrograde orbits around a small natural satellite

An analytical expression for distant retrograde orbits (DROs) is obtained in this study. Owing to the fact that a planar DRO is a closed orbit and can be expressed as an approximately elliptical orbit, respective geometries and periods of DROs are analytically calculated. A switching point, where various properties of planar DROs change abruptly with an increase in the orbital radius, is determined. The Mars–Deimos system is taken as a case study in this work. The proposed method can be applied to cases where the Hill’s approximation of the restricted three-body problem is valid. Numerical calculations are performed to validate the proposed method.     

Influence of curved thin-film device on deformation of a solar sail

A spinning solar sail IKAROS’s membrane is estimated to unexpectedly deform into an inverted pyramid shape due to thin-film devices with curvature, such as thin-film solar cells and steering devices on the membrane. It is important to investigate the deformation caused by the curved thin-film devices and predict the sail shape because the out-of-plane deformation greatly affects solar radiation pressure (SRP) and SRP torque. The purpose of this paper is to clarify the relationship between the global shape and orientation and position of curved thin-film devices and to evaluate SRP torque on the global shape using finite element analysis. The global shape is evaluated based on the out-of-plane displacement and the SRP torque. When the curved thin-film devices make the membrane shrink in the circumferential, diagonal, and radial direction, the sail deforms into a pyramid shape, an inverted pyramid one, and a saddle one, respectively. The saddle shape is more desirable for solar sails than the inverted pyramid shape and the pyramid one from the viewpoint of shape stability to SRP and control of SRP torque in the normal direction of the sail (windmill torque). The position of the thin-film device tends to increase the absolute value of windmill torque when it is biased circumferentially from the petal central axis. The suggested design principles for the arrangement of thin-film devices is that the curved thin-film devices should be directed so that the sail shrinks in the radial direction in order to deform the sail into a saddle shape with high shape stability, and the position of the thin-film devices should be biased in the circumferential direction paying attention to the absolute value of windmill torque to determine the direction of windmill torque.     

Solar power sail membrane prototype for OKEANOS mission

This paper reports on the manufacturing and evaluation of a solar power sail membrane prototype for the OKEANOS project. The in-house prototype was built by the Institute of Space and Astronautical Science, Japan Aerospace Exploration Agency. Mechanical and electrical evaluation tests were conducted. The membrane, thin-film solar cells, reflectivity control devices were good condition after the manufacturing and handling. The improvements in the manufacturing process and design were found. The manufacturing process and design were fundamentally established. After the prototype, improvement plans for the manufacturing process and design were tried. We have a prospect of manufacturing the flight model sail and continue to the development.     

Signal Interference and Improvement of Signal-to-Noise Ratios in a Half-Wave Linear Detector

Signal interference in the half-wave linear detector has been studied only for amplitude modulation. In this paper, we treat signal interference for both an amplitude-and an angle-modulation communication system. The input to the half-wave linear detector is assumed to be composed of an amplitude-modulated wave, an angle-modulated wave, and narrow-band Gaussian noise. In particular, when strongweak relations exist in the input processes, a detailed analysis for the output component is presented to clarify some useful output properties.