机械连接件中螺栓孔角裂纹应力强度因子数值计算(英文)

The three-dimensional finite element method is used to solve the problem of the quarter-elliptical comer crack of the bolt-hole in mechanical joints being subjected to remote tension. The square-root stress singularity around the corner crack front is simulated using the collapsed 20-node quarter point singular elements. The contact interaction between the bolt and the hole boundary is considered in the finite element analysis. The stress intensity factors （SIFs） along the crack front are evaluated by using the displacement correlation technique. The effects of the amount of clearance between the hole and the bolt on the SIFs are investigated. The numerical results indicate that the SIF for mode I decrease with the decreases in clearance, and in the cases of clearance being present, the corner crack is in a mix-mode, even if mode I loading is dominant.     

平板型MLHP温度波动研究

环路热管(Loop Heat Pipe,LHP)是一种靠蒸发器的毛细芯产生毛细力驱动回路运行,利用工质相变来传递热量的高效传热装置。研制了一套平板式蒸发器、风冷式冷凝器的小型环路热管(MLHP),MLHP的毛细芯为500目不锈钢丝网,工质为丙酮,蒸发器、冷凝器以及所有管路均由紫铜制成。主要研究了平板型MLHP在不同热负荷条件下的温度波动特性,并重点研究了倾角以及充灌量等对MLHP系统温度波动的影响,且给出相应的合理解释。实验结果表明,平板式MLHP在2~3W/cm2热流密度区间范围内容易发生温度波动。     

Electrochemical micromachining of microgroove arrays on phosphor bronze surface for improving the tribological performance

A high friction coefficient and a low wear rate of contacted surfaces are essential elements to friction pairs between the stator and the rotor in ultrasonic motors. It has been shown that surface textures have a significant effect on improving the tribological performance of friction pairs.In this paper, microgroove arrays are introduced to the stator surface for improving the tribological performance of friction pairs between the stator and the rotor in ultrasonic motors. Microgrooves were fabricated on a phosphor bronze surface by through-mask electrochemical micromachining(TMEMM). Parameters, namely, the electrolyte inlet pressure, applied voltage, pulse duty cycle,and frequency, were varied to investigate their influences on the dimensions and morphology of the microgrooves. Results showed that the width and depth of the microgrooves were strongly affected by the applied voltage and frequency, while the morphology of the microgrooves was dependent on the electrolyte inlet pressure and the pulse duty cycle. Compared with a smooth surface, the friction coefficient increased from 0.245 to 0.334 and less abrasion was obtained when a surface was textured with microgrooves of which the width and depth were 185.6 and 57.6 lm,respectively. Microgroove arrays might play an important role in enhancing the performance of ultrasonic motors.     

Determination of Failure Thresholds in Hybrid Navigation

A systematic approach for the determination of failure thresholds for hybrid navigation systems is described. Cost functions which reflect the importance assigned to the consequences of false and missed alarms are minimized. The false alarm probability is obtained as a function of the threshold magnitude by observing the statistical behavior of the instrument outputs in the normal operating mode. The missed alarm probability is obtained by determining the sensitivity of navigation error performance to instrument error sources. Two cost functions are considered. To illustrate this method, failure detection and identification (FDI) thresholds are determined for the Space Shuttle Approach and Landing Test flight.     

The data compression problem for the “GAIA” astrometric satellite of ESA

Space-based astrometry has a great tradition at ESA. The first space-based astrometric satellite in history, “Hipparcos”, was launched by ESA in 1989 and, in spite of orbital problems, was able to accomplish almost all of its tasks until it was finally shut down in 1993. The results of the Hipparcos mission were published by ESA in 1997 in the form of six CD-ROMs: the Hipparcos Catalogue contains 118,218 entries with median astrometric precision of around 1 milliarcsec, and specific results for double and multiple systems. In practice, Hipparcos drew for the first time the three-dimensional “map” of the spherical region of the Galaxy surrounding the Sun and having a radius of roughly 1,000 light years.

Then, in 1995, ESA launched the study of a new astrometric satellite, named “GAIA” and about a hundred times more powerful than Hipparcos, i.e. with median astrometric precision of around 10 microarcsec. This new satellite is intended to measure the parallaxes of over 50 million stars in the Galaxy, at least for the brightest stars, and this would mean to “draw” the three-dimensional map of the whole Galaxy, reaching out even to the Magellanic Clouds, 180,000 light years away.

The team of European scientists and engineers now designing GAIA, however, is facing hard technological difficulties. One of these is the design and coding of radically new and ultra-powerful mathematical algorithms for the on-board compression of the 50-million-stars data that GAIA will send to Earth from its intended geostationary orbit. Preliminary estimates of the raw data rates from the GAIA focal plane, in fact, are of the order of a few Gigabits per second. To reduce the data stream to the envisaged telemetry link of 1 Megabit per second, on-board data compression with a 1 to 1,000 ratio is the target. Clearly, this is far beyond the capabilities of any lossless compression technique (enabling compression ratios of 1 to some tens), and so some “wise” lossy compression mathematical procedure must be adopted.

In this paper a GAIA-adapted lossy data compression technique is presented, based on the Karhunen-Loève Transform (KLT). The essence of this method was already used by NASA for the Galileo mission when the large antenna got stuck and the mission was rescued by re-programming the on-board computer in terms of the KLT. That transform was officially named ICT — “Integer Cosine Transform” — by the NASA-JPL team led by Dr. Kahr-Ming Cheung. But the KLT here described for GAIA will of course differ from the JPL one in many regards, owing to the advances in computer technology.

Finally, estimates are also given about the possibility of using the KLT for onboard data compression in case GAIA is going to be put into orbit around the Lagrangian point L2 of the Earth-Sun system, and, above all, in case the number of stars to be observed is actually raised from 50 millions to one billion, as ESA currently appears to be likely to pursue.     

Gamma astrometric measurement experiment (GAME) – Science case

We report here on the science case of a concept for a satellite orbiting at 1 AU from the Sun and using a baffled Fizeau interferometer to look as close as possible to its limb. This configuration, and the need for looking nearby the Sun, is required for the main scientific driver of the mission, namely the measure of the γ parameter of the Parameterized Post-Newtonian formulation to the 10⁻⁶–10⁻⁷ level at least. This would lead to an accurate test of the General Theory of Relativity against other alternative theories of gravity, and set stringent constraints on some of the most significant issues of Astrophysics like those involving exotic forms of dark matter and dark energy. Exploiting the possibilities offered by the observation strategy, it is also possible to target other interesting scientific goals. One is, again, in the realm of General Relativity and aims at measuring the light deflection nearby the Giant Planets to detect asymmetric effects induced by their quadrupoles, predicted by GR but never measured so far. Others can be found in the observation of selected extrasolar systems where, e.g., the astrometric and photometric capabilities of GAME will help to improve on the knowledge of the brown-dwarf regime and on the search for exo-planets with the transit method, respectively.     

低压铸造的计算机控制系统

低压铸造的控制得到人们的日趋重视。本文讨论的是以单片机为基础的低压铸造计算机控制系统。     

高速撞击充气压力容器前壁损伤数值模拟

针对空间碎片超高速撞击充气压力容器前壁损伤问题,应用非线性动力学分析软件AUTODYN采用拉格朗日方法对球形弹丸撞击球形压力容器前壁穿孔进行了数值模拟研究。在建模过程中通过对容器壁内侧施加压力边界条件来模拟由于内充气体的作用在容器壁内产生的应力场,并通过与试验结果的比较验证了数值模拟方法的有效性。在此基础上针对容器的内充气体压力、球形弹丸直径及撞击速度对充气压力容器前壁穿孔的影响进行了研究。结果表明:在一定的气体压力下,气体压力对压力容器前壁穿孔直径与穿孔形态的影响可以忽略不计;而撞击速度及弹丸直径对穿孔直径及穿孔形态有着较大的影响,当撞击速度大于3km/s时,撞击穿孔边缘开始有裂纹产生,并且穿孔直径与裂纹直径随着弹丸直径及撞击速度的增加而增大。利用压力容器前壁穿孔的数值模拟结果进行计算可以得出当容器受到撞击速度大于3km/s的弹丸撞击后比撞击速度不大于3km/s时更易发生破坏。     

远程教学原理与课件制作方法

课件是一种 Ｗｅｂ 文档，所有 Ｗｅｂ 文档技术均可用于制作课件。本文阐述了远程教学系统的原理和课件实现方法，并实现了一个远程教学课件———讲授 Ｉｎｔｅｒｎｅｔ 的基本知识和 Ｈ Ｔ Ｍ Ｌ 语言。     

In-Flight Parity Vector Compensation for FDI

The performance of a failure detection and isolation (FDI) algorithm applied to a redundant strapdown inertial measurement unit (IMU) is limited by sensor errors such as input axis misalignment, scale factor errors, and biases. A techique is presented for improving the performance of FDI algorithms applied to redundant strapdown IMUs. A Kalman filter provides estimates of those linear combinations of sensor errors that affect the parity vector. These estimates are used to form a compensated parity vector which does not include the effects of sensor errors. The compensated parity vector is then used in place of the uncompensated parity vector to make FDI decisions. Simulation results are presented in which the algorithm is tested in a realistic flight environment that includes vehicle maneuvers, the effects of turbulence, and sensor failures. The results show that the algorithm can significantly improve FDI performance, especially during vehicle maneuvers.