石英玻璃的等离子体抛光技术研究现状

具有耐腐蚀、热膨胀系数低等诸多优良物理化学特性的石英玻璃在高性能光学系统中被广泛使用。要求元件达到纳米级别的表面粗糙度，而且没有损伤层和残余应力，因此精加工之后的超精密抛光工序尤为重要。本文介绍了气囊、磁流变、弹性发射、离子束等几种石英玻璃的精密抛光方法，侧重阐述了国内外等离子体的抛光技术，包括等离子体辅助化学刻蚀、等离子体喷射加工、等离子化学蒸发加工研究进展及取得的成果；且对等离子体的未来发展进行概述。     

Energy principle and material removal sequence optimization method in machining of aircraft monolithic parts

In the machining process of aircraft monolithic parts, the initial residual stress redistribution and structural stiffness evolution often lead to unexpected distortions. On the other hand, the stress redistribution and stiffness reduction during the machining process depend on the material removal sequence. The essence of the stress redistribution is releasing the initial elastic strain energy. In the present study, the influence of the material removal sequence on the energy release is studied. Moreover, a novel optimization method is proposed for the material removal sequence. In order to evaluate the performance of the proposed method, the mechanism of the machining distortion is firstly analyzed based on the energy principle. Then a calculative model for the machining distortion of long beam parts is established accordingly. Moreover, an energy parameter related to the bending distortion and the procedure of the material removal sequence optimization is defined. Finally, the bending distortion analysis and material removal sequence optimization are performed on a long beam with a Z-shaped cross-section. Furthermore, simulation and experiments are carried out. The obtained results indicate that the optimized sequence results in a low distortion fluctuation and decreases the bending distortion.     

Experimental and numerical investigation on surface quality for two-point incremental sheet forming with interpolator

The unsatisfied surface quality seriously impedes the wide application of incremental sheet forming (ISF) in industrial field. As a novel approach, the interpolator method is a promising strategy to enhance the surface quality in ISF. However, the mechanism for the improvement of surface quality and the influence of interpolator properties on surface roughness are not well understood. In this paper, the influences of process variables (i.e. tool diameter, step size and thickness of interpolators) on the forming process (e.g. surface roughness, forming force and geometric error) are investigated through a systematic experimental approach of central composite design (CCD) in two-point incremental sheet forming (TPIF). It is obtained that the increase in thickness of interpolators decreases the surface roughness in direction vertical to the tool path while increases the surface roughness in direction horizontal to the tool path. Nevertheless, the combined influence between thickness of interpolators and process parameters (tool diameter and step size) is limited. Meanwhile, the placement of interpolator has little influence on the effective forming force of blank. In addition, the geometric error enlarges with the increase of step size and thickness of interpolator while decreases firstly and then increase with an increase in tool diameter. Finally, the influencing mechanism of the interpolator method on surface quality can be attributed to the decrease of the contact pressure due to the increase of contact area with the unchanged contact force. Meanwhile, the interpolator method eliminates the sliding friction on the surface of blank due to the stable relative position between the blank and the interpolator.     

Influence of thickness and initial groove angle in M–K model on limit strain of 7B04 by considering through-thickness stress

Marciniack–Kuczinski (M–K) model is widely used to predict material’s forming limit curve (FLC). The prediction of FLC traditionally neglected through-thickness normal stress. However, it cannot be neglected in some forming processes. Much work has been done to study the effect of through-thickness normal stress on FLC with constant through-thickness normal stress or constant ratio of through-thickness normal stress and maximum principal stress. In addition, based on Nakazima test process, the ratio of through-thickness normal stress and maximum principal stress has been derived, which was a function of instantaneous thickness and loading path. Here, initial groove angle in M–K model was not considered. In this paper, uniaxial tension tests and Nakazima tests were performed on 7B04 aluminum alloy. Based on Hill 48 yield criterion and M–K model, the prediction model of FLC was established. The increase of thickness can enhance FLC. Meanwhile, it is necessary to consider through-thickness normal stress and initial groove angle in prediction model. On the left side of FLC, the effect of initial groove angle on FLC is weakened by increasing sheet thickness. On the right side of FLC, the effect of initial groove angle on FLC is strengthened by increasing sheet thickness. On the right side of FLC, the relation between limit strain points with different thicknesses is linear under one certain loading path. Thickness has decisive effect on through-thickness normal stress level and the changing trendy of through-thickness normal stress during calculation is different under different stress condition.     

超高强高韧马氏体时效钢热变形及航天应用研究

对于航天用超高强高韧C300马氏体时效钢来说,热加工过程中获得等轴细小的再结晶晶粒是实现该钢强韧性最佳匹配的关键环节。采用Gleeble-3800热模拟试验机在温度为850～1 150℃、应变速率为0.01～10 s~(-1)的条件下,对超高强高韧C300马氏体时效钢进行高温轴向压缩变形试验,获得了高温流变曲线,并观察变形后的金相组织。结果表明:C300马氏体时效钢的流变应力和峰值应变随着变形温度的升高和应变速率的降低而减小;试验钢在真应变为0.92、应变速率为0.01～10 s~(-1)的条件下,随着变形速率的提高,其发生完全动态再结晶的温度也逐渐升高,最佳热变形温度区间为1 050～1 150℃;测得试验钢的热变形激活能Q值为391.2 kJ/mol,建立了其热变形本构方程。结果能为C300马氏体钢的数值模拟和热加工工艺的制定提供理论基础。     

Effects of Mach numbers on Magnus induced surface pressure

Experimental and numerical methods were used to investigate the Magnus phenomena over a spinning projectile. The pressure force acting on the surface of a spinning projectile was measured for various cases by employing a relatively novel experimental technique. A set of miniature pressure sensors along with a data acquisition board, battery and storage memory were placed inside a spinning model and the surface pressure were obtained through a remotely controlled system. Circumferential pressures of the model for both rotational and static conditions were obtained at two different free stream Mach numbers of 0.4 and 0.8 and at different angles of attack. The results showed the ability of this new test method to measure the very small Magnus force via surface pressures over the projectile. The results provide a deep insight into the flow structure and illustrate changes in the cross-flow separation locations as a result of rotation. Similar results were obtained by the numerical simulations and were compared with the experimental data.     

A novel framework for liquid propellant engine’s cooling system design by sensitivity analysis based on RSM and multi-objective optimization using PSO

One of the challenges of combustion chamber and nozzle design in a Liquid Propellant Engine (LPE) is to predict the behavior and performance of the cooling system. Therefore, while designing, the optimization of the cooling system is always of great importance. This paper presents the multi-objective optimization of the LPE’s cooling system. To this end, a novel framework has been developed, resulting from the application of the Response Surface Method (RSM) and the correlation coefficients matrix, sensitivity analysis and the The Particle Swarm Optimization (PSO). based on this method, the input variables, constraints, objective functions, and their surfaces were identified. In terms of multi-optimization algorithms, RSM and PSO are utilized to get global optimum. In conclusion, the methodology capability is to optimize the LPE’s cooling system, 6 percentage increase in total heat transfer and 7 bar decrease cooling system pressure loss, which resulted in a 1.2-seconds increase in the specific impulse of the engine.     

平板表面薄圆柱绕流摩擦力矢量场全局测量

针对壁面摩擦力矢量场测量问题,基于剪切敏感液晶(SSLC)涂层技术建立了一种测量平板表面摩擦力矢量场的方法。该方法基于多视角测量原理,采用六台同步相机从不同方向同时采集SSLC涂层在摩擦力作用下的颜色变化,与采用单台相机相比能够降低测量噪声,并且具有测量非定常流动的摩擦力场的潜力。应用该方法测量了平板表面薄圆柱绕流的摩擦力矢量场,结果表明:(1)SSLC涂层能够以彩色方式定性显示壁面摩擦力信息;(2)通过对不同方向观测的SSLC涂层颜色进行分析处理,该方法能够高分辨率测量薄圆柱绕流的摩擦力矢量场,详细地捕获了流动特征;(3)同一份SSLC涂层可以重复使用并且可用于测量不同的摩擦力矢量场。     

含多部位损伤搭接结构应力强度因子三维有限元分析

应力强度因子(Stress intensity factor,SIF)分析是含多部位损伤(Multiple site damage,MSD)结构剩余强度和裂纹扩展寿命预测的基础和关键。考虑接触与摩擦,建立了含MSD搭接结构的三维有限元模型,研究了不同裂纹长度、铆钉类型以及损伤模式下裂纹尖端SIF分布情况和变化规律。结果表明,搭接件孔边裂纹Ⅰ型SIF起主导作用,Ⅱ型和Ⅲ型SIF可忽略不计。由于次弯曲、铆钉变形和板厚度等因素,SIF在外表面最小,接触面一侧较大,最大值多位于蒙皮内部。MSD会使裂纹间的干涉作用增强,SIF增大,且裂纹间距离越近干涉作用越强。裂纹长度相同时,埋头铆钉的孔边裂纹SIF积分均值大于平头铆钉,且接触面的SIF埋头铆钉大于平头铆钉,外表面则相反。     

A user-friendly yield criterion for metals exhibiting tension-compression asymmetry

The aim of this paper is to model the yielding asymmetry of pressure-insensitive metals, including but not limited to Ni₃Al alloys. The main focuses are put on the flexibility and manipulative convenience. The parameters of theory are kept to a minimum and can be determined by as few tests as possible. These requirements are fulfilled by constructing a yield function using the second and third-invariants of a linearly transformed stress tensor. The proposed yield criterion has a simple mathematical form and has only seven parameters when used in three-dimensional stresses. Compared with existing theories, the new yield criterion has much fewer parameters, which makes it very convenient for practical applications. The coefficients of the criterion are identified by an error minimization procedure. Applications to a Ni₃Al based intermetallic alloy as well as a Cu-Al-Be shape memory alloy and comparison to other criteria show that the proposed criterion has nearly the same predictive ability and flexibility with other criteria. The proposed yield criterion can estimate the coefficients by using less data, which is a big advantage compared with other similar theories, especially when there is a limited number of experimental data.