基于T-S模糊模型的模糊大系统的混合滤波

针对非线性大系统内部过程参数的检测估计,采用连续模糊大系统模型,利用lyapunov定理和分布式处理方法,给出了模糊大系统的H2/H∞混合滤波器设计方法。该方法在保证滤波误差系统全局稳定的同时,具备了H2/H∞性能。通过求解线性矩阵不等式,可以得到滤波器参数。最后,用一个数值例子验证了该方法的正确性和有效性。     

树脂砂低压铸造工艺研究与应用

研究了树脂砂低压铸造工艺理论与原理,结合工艺试验得到了铝合金ZL104涡轮泵出口管树脂砂低压铸造工艺规范。采用该工艺规范制造的铝合金ZL104涡轮泵出口管已用于CZ-5和CZ-7运载火箭液氧煤油液体火箭发动机之中,CZ-5和CZ-7运载火箭已通过了飞行考核,液氧煤油液体火箭发动机工作正常。由此表明:铝合金ZL104涡轮泵出口管树脂砂低压铸造工艺是合理、正确和有效的。     

超高速撞击下PTFE/Al含能材料薄板的载荷特性分析

不同于传统惰性材料的空间碎片防护结构,含能材料防护结构在超高速撞击下的冲击起爆特性是其防护能力得以提高的根本原因。PTFE/Al含能材料防护结构的冲击起爆特性改变了弹丸强冲击载荷下的破碎机制,弹丸内部的冲击压力对于分析含能材料在超高速撞击下的防护机理具有重要意义。对超高速撞击试验中回收的PTFE/Al防护结构后板进行损伤特性分析,获得了对应速度条件下弹丸的破碎特性。基于一维冲击波理论,分析PTFE/Al靶板在超高速撞击条件下的冲击响应过程,结合考虑化学反应效率的热化学反应模型,获得了弹丸在碰撞与爆炸联合作用下的载荷特性,通过与试验结果对比验证,获得该材料完全反应的临界撞击速度约为1800 m/s,弹丸的临界破碎速度为2875 m/s,小于铝防护结构中对应的临界破碎速度。给出了弹丸在PTFE/Al、铝两种防护结构中产生相同冲击压力时对应的临界速度,分别为弹道段的800 m/s和破碎段的3580 m/s。     

基于微观图像及内聚力模型的复合材料裂纹扩展模拟

为研究材料微观结构及晶界强度对材料力学性能的影响,在晶界处引入内聚力单元模型,模拟晶间破坏过程。以ZrB_2-SiC复合材料为研究对象,将其扫描的微观结构图片进行矢量化处理,并导入ABAQUS有限元软件中建立模型,同时在其晶界处,设置内聚力单元模拟晶界破坏过程。通过改变Zr B2与Si C相界面强度,得到了晶界及材料不均匀对材料应力分布及裂纹扩展的影响。结果表明,由于晶界的存在,材料内部出现应力分布不均匀现象并产生应力集中。随着晶界强度的改变,裂纹起始位置及扩展方向发生改变,且裂纹沿低强度的界面进行扩展。随着ZrB_2-SiC界面强度增大,材料的强度提高,拉伸模量不变。     

阻燃钛合金Ti40的热物理性能及力学性能

作为一种功能性钛合金,Ti40阻燃钛合金的热物理性能数据首次被报道。采用真空自耗电弧熔炼技术制备的Ti40合金铸锭成分均匀,利用热挤压开坯+包套保护锻造方法制备的板坯组织均匀。性能测试结果表明:Ti40合金的室温抗拉强度为950 MPa级,且在500℃下具有良好的热暴露性能、高温蠕变性能和高温持久性能。在室温到600℃范围内,合金的杨氏模量和剪切模量随着温度的升高呈线性下降,泊松比随着温度升高而缓慢增加;线性热膨胀曲线随着温度升高呈抛物线增加,平均线膨胀系数随着温度的升高呈线性增加。     

弹性体运载火箭建模及控制器设计

考虑运载火箭飞行过程中的弹性振动特性,对运载火箭进行全量动力学建模以及控制器设计。首先将运载火箭考虑为一维梁模型并建立全量动力学模型,分别引入自适应滤波姿态控制算法和H_2范数鲁棒增益调度控制算法设计控制器。仿真结果表明:在考虑舵机非线性情况下两种控制方法均能够满足精度要求,在具有较大外部扰动情况下,鲁棒增益调度控制算法相较于自适应滤波算法具有较强的鲁棒性。     

Evolution of periodic orbits near the Lagrangian point L2

A study of the evolution of the periodic and the quasi-periodic orbits near the Lagrangian point L₂, which is located to the right of the smaller primary on the line joining the primaries and whose distance from the more massive primary is greater than the distance between the primaries, in the framework of restricted three-body problem for the Sun–Jupiter, Earth–Moon (relatively large mass ratio) and Saturn–Titan (relatively small mass ratio) systems is made. Two families of periodic orbits around the smaller primary are identified using the Poincaré surface of section method – family I (initially elliptical, gradually becomes egg-shaped with the increase in the Jacobi constant C and elongated towards the more massive primary) and family II (initially egg-shaped orbits elongated towards L₂ and gradually becomes elliptical with the increase in C). The family I in the Sun–Jupiter and Saturn–Titan systems contains two separatrix caused by third-order and fourth-order resonances, while the Earth–Moon system has only one separatrix which is caused by third-order resonances. Also in the Sun–Jupiter and the Saturn–Titan systems, family I merge with family II, around Jacobian constant 3.0393 and 3.0163, respectively, while in the Earth–Moon system, family II evolves separately from two different branches. The two branches merge at C = 3.184515. In the Earth–Moon system, the family II contains a separatrix due to third-order resonances which is absent in the other two systems.     

Comparison of peak characteristics of F2 ionospheric layer over Tehran region at a low solar activity period with IRI-2001 and IRI-2007 models predictions

In the present work values of peak electron density (NmF2) and height of F2 ionospheric layer (hmF2) over Tehran region at a low solar activity period are compared with the predictions of the International Reference Ionosphere models (IRI-2001 and IRI-2007). Data measured by a digital ionosonde at the ionospheric station of the Institute of Geophysics, University of Tehran from July 2006 to June 2007 are used to perform the calculations. Formulations proposed by  and  are utilized to calculate the hmF2. The International Union of Radio Science (URSI) and International Radio Consultative Committee (CCIR) options are employed to run the IRI-2001 and IRI-2007 models. Results show that both IRI-2007 and IRI-2001 can successfully predict the NmF2 and hmF2 over Tehran region. In addition, the study shows that predictions of IRI-2007 model with CCIR coefficient has closer values to the observations. Furthermore, it is found that the monthly average of the percentage deviation between the IRI models predictions and the values of hmF2 and NmF2 parameters are less than 10% and 21%, respectively.     

基于I~2C总线的CPU温度监控系统

随着高性能、高功耗器件在嵌入式领域中广泛应用,温度监控已成为高可靠嵌入式领域研究的热点,采用ADI公司的测温电路ADT7461设计了面向高性能PowerPC处理器的温度监控系统。介绍了ADT7461芯片的功能原理,描述了整个硬件电路的结构。在软件部分阐述了I2C总线协议以及基于I2C总线协议实现的ADT7461寄存器读/写基本操作,针对应用中会面临的实际问题给出了具体解决方法。设计方法对于同类温度监控系统设计有一定的参考意义。     

填加造孔剂法制备泡沫铝及其吸能性能

以尿素为造孔剂,采用填加造孔剂法制备泡沫铝,系统研究了成型烧结温度、孔隙率和孔径大小对泡沫铝吸能性能的影响,在此过程中采用电子万能试验机和数字图像相关(DIC)技术同步测试分析。结果表明:填加造孔剂法可以良好的控制泡沫铝的孔隙率和孔径;泡沫铝的最佳成型烧结温度为650℃,在此温度下,泡沫铝的压缩屈服强度达到10.7 MPa;随着孔隙率的降低,泡沫铝的屈服强度和平台应力逐渐提高,材料吸能性能有显著增强;当孔径小于2.0 mm时,随着孔径的增大,材料的吸能性能小幅提高。DIC技术可以直观的表征泡沫材料力学行为,具有良好的工程应用前景。