平箔片楔形高度对气体止推箔片轴承特性影响

针对波箔型气体止推箔片轴承,建立了箔片结构二维薄板模型,并通过有限差分法和有限元法耦合求解可压缩气体Reynolds方程和气膜厚度方程,获得了给定轴承载荷条件下轴承气膜压力分布、气膜厚度分布、平箔片变形量和功率损耗等轴承特性.通过对比楔形高度分别为25,70,100,200,300μm时的轴承特性仿真结果研究了楔形高度对轴承性能的影响.结果表明:降低楔形高度使轴承气膜压力分布更均匀,并降低了平箔片的局部集中载荷.但楔形高度存在一个最佳值,使得达到相同轴承载荷所需的最小气膜厚度最大,并且轴承具有最小功率损耗,提高了轴承的工作效率.该结果为气体止推箔片轴承的结构设计提供的理论参考.      

Advances and trends in plastic forming technologies for welded tubes

With the implementation of environmental protection, sustainable development and conservation-oriented policies, components and parts of thin-walled welded tubes have gained increasing application in the aircraft and automotive industries because of their advantages: easily achieving forming and manufacturing process at low cost and in a short time. The current research on welded tube plastic forming is mainly concentrated on tube internal high-pressure forming, tube bending forming, and tube spinning forming. The focuses are on the material properties and characterization of welded tubes, finite element modeling for welded tube forming, and inhomogeneous deformation behavior and the mechanism and rules of deformation coordination in welded tube plastic forming. This paper summarizes the research progress in welded tube plastic forming from these aspects. Finally, with a focus on the urgent demand of the aviation, aerospace and automotive industries for high-strength and light-weight tubes, this paper discusses the development trends and challenges in the theory and technology of welded tube plastic forming in the future. Among them,laser tailor-welded technology will find application in the manufacture of high-strength steel tubes.Tube-end forming technology, such as tube flaring and flanging technology, will expand its application in welded tubes. Therefore, future studies will focus on the FE modeling regarding how to consider effects of welding on residual stresses, welding distortions and microstructure, the inhomogeneous deformation and coordination mechanism of the plastic forming process of tailor-welded tubes, and some end-forming processes of welded tubes, and more comprehensive research on the forming mechanism and limit of welded tubes.     

带非线性支撑的转子有限元模型求解方法

用数值方法研究了非线性支撑的柔性转子系统的动学行为,提出了一种将有限元与非线性支撑结合的模型和求解方法。利用有限元法(FEM)构建转轴和转盘部分的模型,通过矩阵进行组合;利用离散元方法对包含滚动轴承和挤压油膜阻尼器(SFD)的支撑部分进行建模,此部分包含4个单元,分别为轴承内圈、外圈、SFD内圈和支撑鼠笼。有限元部分和离散元部分通过轴端节点相连,仿真过程中轴端位移传递给非线性支撑部分,支撑部分通过位移计算得到的非线性力反过来作用于有限元转子轴端部分。为了耦合求解有限元转子和非线性支撑组成的数学模型,提出了一种综合的迭代求解方法,克服传统的有限元求解方法对轴端隐性非线性支撑的求解局限性。由于转轴部分采用了Timoshenko梁单元建模,对比与简单转子模型,可以考虑陀螺力矩和轴的柔性特征,更能体现非线性支撑对振动真实影响。在建立的20个轴单元的有限元转子模型中,非线性响应更多体现在靠近非线性支撑的节点1和节点21处,响应频谱中靠近轴端的节点能体现出滚动轴承的2倍和3倍变柔振动频率。     

Cross-sectional deformation behavior of double-ridged rectangular tube with fillers in different stages of H-typed bending

The bent double-ridged rectangular tube (DRRT) with high forming quality is helpful to improve the microwave transmission accuracy. For reducing the cross-sectional deformation in the H-typed bending process, in addition to using rigid mandrel to support the inside of tube, ridge groove fillers are also added to restrict the deformation of ridge grooves. Because of the change of stress and strain state of bent tube in bending, rigid mandrel retracting and specially twice-springback stages, and the springback of fillers, the cross-sectional deformation of tube in each stage may be different. Therefore, based on the ABAQUS platform, the finite element models (FEM) for H-typed bending, mandrel retracting and twice-springback stages of H96 DRRT with fillers were established and validated. It is found that, for the height and width deformation of tube and spacing deformation of ridge grooves, retraction of mandrel can make the distribution of these deformations more uniform along the bending direction. The first springback can reduce these deformations significantly, which should be emphasized. But the second springback only increases them by less amount, which can be ignored. The smaller height deformation of ridge groove and filler can be neglected.     

整体弹性结构法及在叶片流固耦合分析中的应用

针对三维叶片时域流固耦合振动响应计算普遍耗时的问题,采用一种假设整体结构的模态位移,求解固体时域响应和实现高效网格变形,发展了一种3维时域流固耦合分析的整体弹性结构方法,并应用于压气机叶片0°和180°相位角的气动稳定性分析中。结果表明,所发展方法的计算结果与传统双向时域算法和文献的结果较为吻合,而计算效率相比于传统算法显著提升;在所分析的两个相位角下,叶片振动的气动阻尼均随流量减小先增大后降低,相比于0°相位角,180°下叶片的气动稳定性大幅提高,表明该方法能有效应用于叶片的工程流固耦合研究。     

大量程MEMS陀螺仪在高速旋转导弹上的应用

弹旋频率是影响旋转导弹制导精度的主要因素之一.本文提出了一种弹旋频率测量用大量程MEMS陀螺仪技术方案,开展了大量程MEMS陀螺仪在旋转导弹上的应用研究,解决了大量程MEMS陀螺仪在偏心安装、较大力学环境下提高测量精度等问题,通过了飞行试验验证,实现了旋转导弹弹旋频率的精确测量.     

数字化组合式大力值校准系统的研制

为了满足对大力值(20 MN左右)的测量和校准,开发了一套数字化组合式大力值校准装置。其最大量程可达24 MN,系统测量准确度为0.1%,适合于大型材料试验机的校准和检定。本文详细介绍了装置的组成结构、弹性体设计、贴片和组桥方式、数字化的方法以及与计算机的通信实现。     

三支点柔性转子系统支承不同心激励特征及振动响应分析

针对航空发动机三支点柔性转子系统的支承不同心问题,充分考虑转子结构特征和载荷特征,首次将当量刚度引入多支点柔性转子不同心问题的动力学分析,定量描述转子系统各支承间不同心度带来的转子轴段刚度非线性,并提出了多跨度柔性转子系统支承不同心激励的数学描述,建立了不同心激励下多跨度柔性转子系统的力学模型。基于Lagrange能量法,给出了转子系统动力学方程的求解方法,研究得到了支承不同心转子系统的动力响应特征。结果表明:支承不同心不仅引起转子过渡轴的刚度非线性,产生2倍频激励,还会给转子系统带来附加不平衡激励;对于三支点柔性转子系统而言,2倍频分量同样是支承不同心下转子系统振动响应的典型特征之一。转子系统2倍频分量随不同心量的增加而迅速增加,而1倍频分量基本保持不变。同时转子振动响应呈现"缓增速降"趋势,且随非线性刚度、不平衡量的增大愈加明显。     

大航向角误差情况下飞行中对准研究

为了解决飞行器在大航向角误差的情况下进行飞行中对准的难题,将一种线性大航向角误差模型应用于飞行器飞行中对准的过程.详细推导了线性大航向角误差模型,设计了飞行器在大航向角误差情况下进行飞行中对准的卡尔曼滤波模型,并进行了数字仿真.仿真结果表明,线性大航向角误差模型应用于飞行器飞行中对准,能够很好地解决飞行器在大航向角误差情况下进行对准的难点,并给出了适合于大航向角误差模型的机动方式.最后,提出了线性大航向角误差模型在工程应用中的几点建议     

增强FMS柔性的关键技术研究

柔性制造技术是现代制造业广泛采用的一种先进的制造技术。实现生产柔性是引进柔性制造技术的根本目的。ＦＭＳ是柔性制造技术应用的典型模式。