三支点柔性转子系统支承不同心激励特征及振动响应分析

针对航空发动机三支点柔性转子系统的支承不同心问题,充分考虑转子结构特征和载荷特征,首次将当量刚度引入多支点柔性转子不同心问题的动力学分析,定量描述转子系统各支承间不同心度带来的转子轴段刚度非线性,并提出了多跨度柔性转子系统支承不同心激励的数学描述,建立了不同心激励下多跨度柔性转子系统的力学模型。基于Lagrange能量法,给出了转子系统动力学方程的求解方法,研究得到了支承不同心转子系统的动力响应特征。结果表明:支承不同心不仅引起转子过渡轴的刚度非线性,产生2倍频激励,还会给转子系统带来附加不平衡激励;对于三支点柔性转子系统而言,2倍频分量同样是支承不同心下转子系统振动响应的典型特征之一。转子系统2倍频分量随不同心量的增加而迅速增加,而1倍频分量基本保持不变。同时转子振动响应呈现"缓增速降"趋势,且随非线性刚度、不平衡量的增大愈加明显。     

Measurements of heat transfer and pressure in a trailing edge cavity of a turbine blade

 An experimental investigation is conducted to obtain the heat transfer and pressure drop data for an integral trailing edge cavity test section that simulates a novel turbine blade's internal cooling passage with bleed holes. Local heat transfer is measured on both the suction and pressure sides by a transient liquid crystal technique, while pressures at six positions are recorded by pressure calibrators. Moreover, flow characteristic and its effect on heat transfer are analyzed for conditions with or without bleed flow. The experimental results show that, in the cases with bleed flow, local heat transfer on the pressure side exceeds that on the suction side in the first and second channels. In the cases without bleed flow, in the first and third channels, local heat transfer on the suction side weakens whilst it increases significantly on the pressure side. For the second channel, non-bleed condition leads to a more balanced heat transfer distribution between the upstream and downstream channel. Besides, after the bleed holes are blocked, heat transfer in the first bend region on the suction side declines sharply, while the opposite phenomenon occurs for the second bend region on the pressure side. In both bleed and non-bleed cases, the total pressure of six measurement positions decreases continuously along the channel at the same Reynolds number and it promotes for higher Reynolds number. Among all the measurement points, under the same flow rate condition, the highest speed occurs at Position 5, which also shows the maximum difference between the total and static pressures. When the bleed holes are blocked, the total pressure at each measurement position appears to increase.     

利用航天器分舱段振动试验数据获取整器响应的方法

未来大型组合体航天器振动试验可能难以在现有设备上进行,需要进行分舱考核。文章针对此问题开展了利用分舱段振动试验获取整器响应的方法研究。提出的方法为:根据不同界面下模态的映射关系,利用单舱段的振动试验数据辨识出舱段的两端固支模态;采用模态综合技术计算出整器组合体模态参数,拟合出结构的加速度响应传递函数;结合整器的加速度试验条件可以给出整器的试验响应曲线。仿真验证结果表明该方法合理可行,具有工程应用价值。     

TRANSIENT RESPONSE INVESTIGATION OF GIMBALLED TILTROTORS DURING ENGAGE AND DISENGAGE OPERATIONS

Ｕｎｉｑｕｅａｎｄｏｆｔｅｎｈａｚａｒｄｏｕｓｃｏｎｄｉｔｉｏｎｓａｒｅｅｎｃｏｕｎｔｅｒｅｄｗｈｅｎｒｏｔｏｒｃｒａｆｔａｒｅｏｐｅｒａｔｅｄｆｒｏｍｓｈｉｐｂａｓｅｄｐｌａｔｆｏｒｍｓ．Ｏｎｅｏｆｔｈｅｍｏｒｅｔｒｏｕｂｌｅｓｏｍｅｒｏｔｏｒｃｒ...     

A novel approach for predicting inlet pressure of aircraft hydraulic pumps under transient conditions

Cavitation caused by insufficient suction is a major factor that influences the life of aircraft pumps. Currently, pressurizing the tank can solve the cavitation problem under steady large-flow conditions. However, this method is not always effective under transient conditions (from zero flow to full flow in a very short time). Moreover, to apply and design other measures, such as a boost impeller, the suction dynamics during the transient period must be investigated. In this paper, a novel approach based on the pressure wave propagation theory is proposed for predicting the inlet pressure of an aircraft pump under transient conditions. First, a dynamic model of a typical aircraft pump is established in the form of differential equations. Then, the transient flow model of the inlet line is described using momentum and continuity equations, and the governing equations are discretized by the method of characteristics and the finite difference method. The simulated results are in good agreement with the results from verification tests. Further simulation analysis indicates that the wave velocity and transient time may influence the inlet and reservoir pressure as well as the size of the inlet line. Finally, solutions for upgrading the inlet pressure are discussed. These solutions provide guidelines for designing inlet installations.     

Mean energy of response to galactic cosmic ray spectrum: IMP 8 and Climax neutron monitor

Solar modulations of galactic cosmic ray (GCR) intensity contain a wealth of information about their transport in the heliosphere. To extract this information from the data one studies the dependence of the observed modulations on the mean energy of response of detectors providing data for the analyses. There is a great deal of confusion about the detector energy response to GCR spectrum in the literature. We present a preliminary report on the computations of the mean energy of response for the Climax neutron monitor (CL/NM) and IMP 8 cosmic ray nuclear composition instrument to GCR protons for 1973–1998, covering the solar cycles 21 and 22. We find that for penetrating proton channel on IMP 8 the mean energy changes by a factor of over two whereas for the neutron monitor the change is only 21%. However, the corresponding change for the computed modulation function is a factor of about 3.5.     

气动力/热与结构多场耦合试验模型方案初步设计

以多渠道、多机制交叉耦合为热防护结构特点的新一代高超声速飞行器必须采用气动力/热与结构多场耦合计算方法进行研究。目前,国外已建立较完善的耦合分析系统并用于飞行器研制,国内的中国空气动力研究与发展中心(CARDC)也已自主研发了热环境/热响应耦合计算平台(FL-CAPTER)。为验证多场耦合计算平台所用方法的有效性和计算结果的准确性,设计并开展气动力/热与结构耦合的地面试验具有十分重要的意义。本文结合气动力/热与结构多场耦合试验设计需求,以现有材料和设备能力为依托,开展了试验风洞选取、模型尺寸估算、模型材料选择、模型气动设计与模型结构设计工作。初步研究表明,模型支撑结构附近迎风面局部高温热膨胀将有利于模型前体结构产生可观的整体变形量。本文以此设计了带压缩拐角的二级压缩面结构模型,通过短时间不锈钢模型验证试验和计算对比分析初步验证了模型设计的可行性,并以此为基础预测了高温合金模型的试验结果。为下一步开展高温合金长时间风洞试验奠定了技术基础。     

带止口法兰连接结构刚度特性对结构振动影响

对带有止口的法兰连接结构刚度特性进行了数值仿真研究。使用有限元软件ANSYS分析了带有止口的法兰连接结构的迟滞特性。通过对止口接触面的变形-滑移机理分析,使用一个詹金斯单元和一个弹簧单元并联模拟法兰的一个扇区,并基于法兰弯曲变形时每个扇区的不同状态建立了整个法兰结构的弯曲刚度简化模型,并对该简化模型进行了仿真,该简化模型能够较准确地模拟带止口法兰连接结构的刚度特性。基于简化模型和梁单元建立了简化转子结构模型,分析了带有止口的法兰连接结构对转子稳态动力学响应的影响。结果表明带有止口的法兰连接结构的迟滞特性能够影响峰值频率,随着止口过盈量的增加，响应峰值显著降低,具有较好的振动抑制效果。      

平方阻尼在非线性缓冲系统中的作用

本文讨论平方阻尼(以参数a表征)在图(1)所示的缓冲系统中的作用,结果表明:平方阻尼对于降低相对位移峰值d_m总有良好的效果,但不一定降低加速度峰值a_m。在一定速度冲击V下,系统的平方阻尼有两种最佳值,使a_m最小的a_(am)和使缓冲效率γ最高的a_(cm),而平方阻尼最佳条件依赖于系统的缓冲弹簧的刚度变化类型: (1)线性弹簧情况:a_(am)=a_(cm),最佳条件为系统在首程中均匀减速; (2)渐硬弹簧情况:a_(am)=a_(cm),最佳条件为系统在首程中初始和终末加速度相等即; aV~2=ω_0~2q(dm) (3)渐软弹簧情况:a_(cm)>a_(am)。 本文的基础是所谓“首程显峰”,假定即系统在速度冲击V下的响应峰值d_m和a_m出现在第一行程中。当平方阻尼值不太小,缓冲弹簧刚度特性接近反对称时,该假定成立。     

Transient simulation of regression rate on thrust regulation process in hybrid rocket motor

The main goal of this paper is to study the characteristics of regression rate of solid grain during thrust regulation process. For this purpose, an unsteady numerical model of regression rate is established. Gas–solid coupling is considered between the solid grain surface and combustion gas.Dynamic mesh is used to simulate the regression process of the solid fuel surface. Based on this model, numerical simulations on a H2O2/HTPB(hydroxyl-terminated polybutadiene) hybrid motor have been performed in the flow control process. The simulation results show that under the step change of the oxidizer mass flow rate condition, the regression rate cannot reach a stable value instantly because the flow field requires a short time period to adjust. The regression rate increases with the linear gain of oxidizer mass flow rate, and has a higher slope than the relative inlet function of oxidizer flow rate. A shorter regulation time can cause a higher regression rate during regulation process. The results also show that transient calculation can better simulate the instantaneous regression rate in the operation process.