神经网络在下颌运动轨迹图测量中的应用

介绍了采用小型磁石测量下颌运动轨迹图Electrognathography(EGN)的方法。给出利用磁偶极子模型代替小磁石模型的理论及实际依据。利用神经网络解决由磁石产生的磁感应强度推定其空间参数的反演问题 ,并且采用了分割网络及修正网络的方法来提高磁石运动测量的推定准确度。     

现代超声工业测量的若干发展

超声波在工业测量领域中的可用性非常广。目前，由于现代电子技术与微机技术的飞速发展；这种可用性得到愈来愈多的体现。本文简要介绍了超声波技术在若干方面的研究进展，其中包括：高精度声速测量，材料应力测量，化工过程检测及超声谱分析技术。     

直接解算轨道根数的轨道约束自校准定轨方法

应用轨道约束自校准技术能够有效地修正系统误差和提高定轨精度。本文为了适应各种航天试验任务要求,将轨道约束自校准技术推广应用到直接解算轨道根数的定轨方法中,并导出了解算开普勒根数的轨道约束自校准公式。     

关于外测新体制的一些分析与思考

针对外测新体制下数据处理中遇到的一些重要问题进行了较为深入的讨论。认真分析了多站测速系统的严重病态以及样条约束的EMBET算法在目标非平稳段的剩余截断误差等制约弹道处理精度的重要问题,并提出解决问题的思路与方法。     

基于单目视觉原理的空间位置测量技术研究

为了提升空间位置测量的自动化程度,采用单目视觉原理建立空间成像方程,将三维的空间坐标转换为两维的图像坐标,由此实现单目视觉的空间位置测量。本文推导了单目视觉定位的基本成像方程,对建立的定位装置,进行了实际定位实验,实现了预期的测量结果。基于视觉原理的空间位置测量技术,具有良好的推广应用价值。     

高速开关阀控电液位置伺服系统自适应鲁棒控制

为研究高精度的液压缸位置跟踪控制问题，设计了高速开关阀和换向阀组合控制液压缸的结构方案，并通过实验分析了高速开关阀的静态流量特性。建立了液压缸的连续可微摩擦模型，利用粒子群优化算法对其参数进行辨识。建立了系统的非线性数学模型，基于非连续参数映射和反步法设计了直接自适应鲁棒控制器，通过参数在线自适应调节来更新估计值和鲁棒反馈项支配参数不确定性，实验结果表明:在跟踪幅值为5mm，频率为0.4Hz的正弦信号时，最后一个周期的最大跟踪误差、平均跟踪误差及其标准差分别为0.638、0.25mm和0.405mm，与传统PID控制器相比，控制精度显著提升，旨在为实现高精度的数字阀控位置伺服技术提供有价值的参考。      

A novel architecture of electro-hydrostatic actuator with digital distribution

To address the flow imbalance rapidly of the asymmetric Electro-Hydrostatic Actuator (EHA), this paper presents a novel architecture of asymmetric EHA with the Digital Distribution (EHA-DD). It also improves the flow nonlinearity and control accuracy of the pump, especially in the low-speed condition. The digital distribution with two High-Speed on–off Valves (HSVs) not only balances flow instead of the check valves, but also replaces the pump at the low-speed to control output flow by adjusting the PWM signal. The pump and HSVs are the crucial components to control flow output. Firstly, the flow calculation models of the pump and the duty ratio inversed model of the HSV are obtained through experimental tests and the identification method. To get the control input signal for the required flow, the pump speed and PWM duty ratio for the HSVs are inversed to compensate for flow output. Further, a multimode digital flow distribution control method based on pump speed, mainly including the pump-controlled mode for large flow demand and valve-controlled mode for little flow demand, is proposed to control the accurate flow output actively. The step extension experiments based on the flow calculation models are conducted on the EHA-DD prototype under elastic, opposite varying load. The results demonstrate that the EHA-DD realizes little position error by accurate flow control, and it is also beneficial to improve the service life of the pump.     

基于单目视觉原理的空间位置测量技术研究

为了提升空间位置测量的自动化程度，采用单目视觉原理建立空间成像方程，将三维的空间坐标转换为两维的图像坐标，由此实现单目视觉的空间位置测量。本文推导了单目视觉定位的基本成像方程，对建立的定位装置，进行了实际定位实验，实现了预期的测量结果。基于视觉原理的空间位置测量技术，具有良好的推广应用价值。     

Fault diagnosis based on measurement reconstruction of HPT exit pressure for turbofan engine

Aero-engine gas path health monitoring plays a critical role in Engine Health Management(EHM). To achieve unbiased estimation, traditional filtering methods have strict requirements on measurement parameters which sometimes cannot be measured in engineering. The most typical one is the High-Pressure Turbine(HPT) exit pressure, which is vital to distinguishing failure modes between different turbines. For the case of an abrupt failure occurring in a single turbine component, a model-based sensor measurement reconstruction method is proposed in this paper. First,to estimate the missing measurements, the forward algorithm and the backward algorithm are developed based on corresponding component models according to the failure hypotheses. Then,a new fault diagnosis logic is designed and the traditional nonlinear filter is improved by adding the measurement estimation module and the health parameter correction module, which uses the reconstructed measurement to complete the health parameters estimation. Simulation results show that the proposed method can well restore the desired measurement and the estimated measurement can be used in the turbofan engine gas path diagnosis. Compared with the diagnosis under the condition of missing sensors, this method can distinguish between different failure modes, quantify the variations of health parameters, and achieve good performance at multiple operating points in the flight envelope.     

碳纤维增强复合材料车削表面质量分析

以PCD刀具车削加工短切碳纤维/酚醛复合材料的表观质量为研究对象,通过开展正交试验,采用三维测量技术,研究切削三要素和刀尖圆弧半径对工件加工质量的影响;通过Design Expert软件,对加工因素的显著性进行分析。结果表明,随着切削速度v和进给量f的增大,表面粗糙度Ra逐渐增大,随着切削深度a_p和刀尖圆弧半径r的增大,Ra逐渐变小;试验显著因素为刀尖圆弧和进给量;最佳加工参数为：v=160 r/min、f=0.15 mm/r、a_p=0.6 mm、r=0.6 mm;通过加工试验和建模分析验证,结论可靠。