激光辅助车削工艺参数对单晶硅表面质量的影响

为了提高单晶硅激光辅助车削加工表面质量,通过开展激光辅助和常规车削加工试验,结合表面粗糙度、表面形貌及拉曼光谱检测,研究激光辅助车削技术对加工质量的影响。基于正交试验方法,研究单晶硅激光辅助车削工艺参数对表面粗糙度的影响;通过方差分析和极差分析评估各因素对表面粗糙度的影响。研究结果表明：与常规车削相比,激光辅助车削可有效提高加工表面质量,降低材料表面的残余应力。主轴转速、进给速度、切削深度和脉冲占空比对表面粗糙度的贡献率分别为17.51%、44.48%、6.69%和14.70%。确定最佳加工参数组合如下：主轴速度为4 000 r/min,进给速度为2 mm/min,切削深度为5μm,脉冲占空比为30%,最终获得表面粗糙度Rq为2.4 nm的高质量表面。     

苯基硅中间体对阻尼硅橡胶性能的影响

为了提高硅橡胶高温下的阻尼性能,将高苯基含量的苯基硅中间体添加到硅橡胶中,并使用硫化剂2,4-二氯过氧苯甲酰(DCLBP)与硅橡胶共硫化。通过无转子硫化仪、SEM、DMA、TG对改性硅橡胶性能进行表征。结果表明:随苯基硅中间体用量的增加,硅橡胶的硫化程度降低,硬度和拉伸强度下降,而拉断伸长率、撕裂强度和高温下的损耗因子tanδ明显提高。当添加量为15份时,硅橡胶拉伸强度为7. 75 MPa,最大损耗因子tanδmax从0. 2提高到0. 3。     

面向硅压阻式压力传感器温度补偿的组合方法

提出一种面向硅压阻式压力传感器温度补偿的组合方法,采用拟合法建立不同温度下压力传感器变换函数,采用基于变换函数系数的线性插值法获得温度补偿后传感器变换函数,设计了压力传感器信号处理模块,开展了基于组合补偿方法的压力信号补偿过程仿真,结果表明经温度补偿后,压力测量精度在0.1%以内,温度补偿过程耗时约10 μs,补偿算法占用片上资源少,能够满足压气机出口压力测量要求。      

Laser-induced oxidation assisted micro milling of high aspect ratio microgroove on WC-Co cemented carbide

Severe tool wear and poor surface quality are the main problems during micro machining of cemented carbide. In this work, an innovative hybrid process of laser-induced oxidation assisted micro milling (LOMM) was proposed to solve the problems. A nanosecond laser was utilized to induce oxidation of the WC-20%Co material, producing loose oxide which was easy to remove. The micro machinability of the material was improved by laser-induced oxidation. The oxidation mechanisms of cemented carbide were studied. A microgroove with a depth of 2.5 mm and aspect ratio of 5 was fabricated successfully. The milling force, surface quality and tool wear mechanisms were investigated. For comparison, a microgroove was also fabricated with conventional micro milling (COMM) using identical milling parameters. Results revealed that in LOMM the milling force and tool wear rate were extremely low during removing the oxide. The machined surface quality and dimensional accuracy achieved by LOMM were superior to those obtained by COMM. The surface roughness S_a of the microgroove bottom reached 88 nm in LOMM, while the cross-sectional geometry of the microgroove was a trapezoid. Perpendicularity of the microgroove sidewall machined by LOMM was better than that by COMM. The tool wear forms in LOMM were coating spalling and slight tool nose breakage. Compared with COMM, the tool life in LOMM was prolonged significantly. It indicates that the proposed hybrid process is an effective and efficient way to fabricate high aspect ratio micro-features with high dimensional accuracy.     

含SiO2,ZrO2微粒复合镀镍层抗高温氧化性能

通过对含有SiO₂,ZrO₂微粒复合电沉积的研究,在Cu合金表面分别获得了含量(原子数分数)为11.3％ SiO₂,5.31％ ZrO₂微粒的Ni基复合镀层.通过在800℃、900℃条件下的高温氧化和热震循环试验,研究了这种复合镀镍层的高温氧化性能和界面结合特性.结果表明:经过40?h的高温氧化,2种复合镀镍层的抗氧化性能均达到抗氧化级,而且含SiO₂微粒的复合镀镍层的抗氧化性能优于含ZrO₂微粒的复合镀镍层;经过55次冷热循环,含SiO₂微粒的复合镀镍层与铜基体结合良好.     

含硼富燃燃气燃烧实验研究

为实现固冲发动机二次燃烧模型验证,结合固冲发动机工作条件,设计了一种带透明观察窗燃烧实验装置;营造了简单的燃烧环境,实现了燃烧过程掺混作用的弱化;借助高速摄像进行了以空气速度作为单一变量的含硼富燃燃气燃烧可视化测量,获得了火焰形态结构;采用高速数据采集,获得了燃烧室压力;将实验数据与数值模拟结果进行了对比和分析。结果表明,燃气与空气速度相近时,火焰呈锥角结构,硼粒子的点火距离较长;燃气与空气速度差较小时,同一位置燃烧室压力较大;燃气与空气速度近似程度决定火焰的形态;数值模拟结果与实验结果基本吻合。     

宽粒径范围颗粒对气相膨胀的影响

利用双流体模型对固体火箭发动机喷管内气固两相流进行计算,研究了两相流中颗粒相与气相的相互作用,分析了颗粒粒径及颗粒质量分数对两相流中气相在喷管中膨胀的影响。结果表明,颗粒粒径造成两相流损失的大小是颗粒比表面积、气相湍流动能及颗粒在喷管内的滞留时间等因素共同作用的结果,两相流损失随着颗粒粒径的增大先增大、后减小,同时随着颗粒质量分数增大而增大;JPL喷管中粒径为2μm的颗粒造成的两相流损失最大,此粒径下,当颗粒质量分数从10％增大到40％时,两相流损失从10％增大到26％。     

计算模拟月壤颗粒吸收及散射特性的一种球叠加模型

针对模拟月壤复杂的外形特征以及多相非均质的微观结构,提出了一种计算模拟月壤颗粒吸收及散射特性的球叠加模型。根据模拟月壤颗粒的形状指数和分形特征识别结果,归纳了4种主要的模拟月壤颗粒类型,并采用蒙特卡罗光线跟踪法研究了这4种颗粒在单色平行光照射下的吸收及散射特性。与已有的非球形颗粒辐射特性的算法比较显示,该模型具有良好的计算准确性。在数值计算的基础上,分析了颗粒尺度参数及光学常数对其自身辐射特性的影响,并通过改变平行光照下的光线入射角度,分析了非球形颗粒的朝向对其自身辐射特性的影响。由计算结果推断,该模型不仅可以应用于计算模拟月壤颗粒的辐射特性,还可以满足其他适用于几何光学近似的非球形粒子。     

On the universality of asymptotic limits in the theory of field line diffusion and perpendicular transport of energetic particles

We discuss the random walk of magnetic field lines in astrophysical plasmas. Based on the standard theory of field line diffusion we show that there are two asymptotic limits. In these limits field line wandering is universal because in both regimes the field line diffusion coefficient depends only on fundamental length scales and absolute magnetic field strengths. As examples we discuss the field line diffusion coefficient for different prominent turbulence models namely the slab model, the two-dimensional model, and the Goldreich–Sridhar model. We show that the field line diffusion coefficient for the latter model agrees with the results obtained for slab and two-dimensional turbulence in limiting cases. We also discuss the transport of energetic particles perpendicular with respect to the mean magnetic field. Based on the unified nonlinear transport theory we consider again asymptotic limits. It is shown that one can identify four different regimes in which the transport is again universal. In all four cases perpendicular transport only depends on fundamental length scales of turbulence, magnetic field values, and the parallel diffusion coefficient.     

硬质合金电火花加工工艺实验研究

针对硬质合金模具的加工表面精度要求,进行了高速钢与硬质合金两种材料的电火花加工工艺对照实验。为获得较低的表面粗糙度,选取了较小的电加工参数。实验结果表明,在该实验条件下,电火花加工的表面粗糙度不再满足常规条件下的经验公式,而与工件材料的再凝结特征、成分及电蚀产物的排出条件有关。