PCD刀具车削不同颗粒含量SiCp/Al复合材料试验研究

碳化硅铝基复合材料具有优良的导热性、较高的比强度和比刚度,在航空航天领域具有广泛的应用前景。由于此复合材料中含有增强相,导致材料的切削加工性能变差。通过试验分析了不同颗粒体积分数(纳米级5%、微米级25%)SiCp/Al复合材料和切削参数(切削速度、背吃刀量、进给量)对刀具磨损和工件表面质量的影响,并对刀具磨损机理进行了研究。试验结果表明,车削微米级25%SiCp/Al材料时聚晶金刚石PCD(Polycrystalline Diamond)刀具磨损更严重,且工件表面质量更差。随着进给量和背吃刀量的增大,工件表面粗糙度值增大,刀片前刀面磨损严重;随着切削速度的增大,工件表面粗糙度值减小,刀片前刀面磨损量增大。选取本文切削参数进行SiCp/Al复合材料的切削加工时,发现刀具磨粒磨损、微崩刃是PCD刀具后刀面磨损的主要成因,且刀具前刀面也会产生积屑瘤。研究结果可为SiCp/Al复合材料PCD车削工艺的优化提供理论基础。     

钛合金端铣时硬质合金刀具磨损机理的研究

 在钛合金铣削加工的过程中,伴随着产生各种物理、化学现象,如变形、切削热、切削力、摩擦与磨损等。而它们之间又是相互联系、相互影响、相互作用。同时又以各自独立的物理、化学和机械现象表现出来。因此只有同时从各个方面对它们进行研究,才能深入揭示其本质。弄清其作用机理,从而去指导生产实践。     

铣削加工参数对SiCp/Al复合材料表面粗糙度的影响

文摘SiC_p/Al复合材料在切削加工中存在严重的表面质量问题。本文设计单因素试验,采用硬质合金涂层刀具对SiC_p/Al复合材料进行铣削加工,研究了加工参数对表面粗糙度的影响。结果表明:表面粗糙度随切削速度的增大先增大后减小,随进给量、径向切深、轴向切深的增大而增大;使用较大的切削速度、较小的进给量和不大于4 mm的径向切深能获得较好的加工表面质量。     

石英纤维增强聚酰亚胺复合材料超低温铣削实验

石英纤维增强聚酰亚胺复合材料是一种非均匀的各向异性材料,采用传统铣削方法对其进行加工时存在刀具磨损严重、切削力较大、加工效率低等问题。为此本文采用超低温冷却铣削方法对石英纤维增强聚酰亚胺复合材料进行铣削实验,并与传统干铣削方式进行了对比,分析了包括加工表面形貌、粗糙度、切削力和刀具磨损等切削性能。结果表明:两种工况下,表面粗糙度随主轴转速的提高而降低,随切深的增加呈先降低后增大趋势;相对于干铣削,不同切削速度下超低温冷却铣削有效抑制了低速干铣削纤维起毛、高速干铣削黏结剂烧蚀缺陷,表面质量都得到改善,刀具耐用度得到提高。超低温冷却引起的复合材料切削力增大,纤维断屑方式的改变以及切削热的有效降低是提高加工质量的主要原因。     

TC17钛合金铣削刀具磨损对残余应力影响研究

为了获得高性能航空发动机用TC17钛合金材料铣削过程中刀具磨损对残余应力的影响规律,通过对不同刀具后刀面磨损量下铣削工件表层残余应力的测试,建立了刀具磨损对残余应力的影响关系,并对影响机理进行了分析。结果表明,硬质合金刀具低速铣削钛合金时,刀具对已加工表面的挤光效应引起的残余压应力占主导地位;不同刀具后刀面磨损量下,残余压应力沿深度方向先增大达到一个最大压应力值后,然后减小趋向于零应力;表面残余应力、最大残余压应力以及残余应力的影响深度都随刀具后刀面磨损量的增大呈增大趋势。     

基于萤火虫算法的CFRP材料铣削刀具结构优化

为了提高CFRP零件的加工表面质量和刀具寿命,针对其铣削加工的刀具结构进行了优化。设计了刀具结构参数与CFRP材料铣削加工表面粗糙度、后刀面磨损量之间的正交试验。应用极差分析法分析了刀具结构参数对CFRP材料加工表面粗糙度、后刀面磨损量的影响规律,并应用多元线性回归法建立了刀具结构参数与表面粗糙度、后刀面磨损量之间的数学模型。基于此模型,采用FA萤火虫算法,优化了刀具的结构参数,并进行了实验验证。结果表明:在试验参数范围内,刀具结构参数对于CFRP工件铣削表面粗糙度的影响程度依次为:后角、螺旋角、前角。当刀具的后角、螺旋角和前角增大时,工件的表面粗糙度都呈减小趋势,但减小的快慢程度不同;刀具结构参数对于后刀面磨损影响程度依次为:后角、螺旋角、前角。当刀具后角增大时,后刀面磨损量迅速上升,当螺旋角增大时,后刀面磨损量减小,当刀具的前角增大时,后刀面磨损量先减小后增大。采用FA萤火虫算法优化后的刀具结构对CFRP材料进行铣削实验,实验结果值与建立的模型预测值误差较小,表面粗糙度的误差率为3%,刀具后刀面磨损量的误差率为7.6%。     

Effects of in-situ TiB2 particles on machinability and surface integrity in milling of TiB2/2024 and TiB2/7075 Al composites

In-situ ceramics particle reinforced aluminum matrix composites are favored in the aerospace industry due to excellent properties. However, the hard ceramic particles as the reinforcement phase bring challenges to machining. To study the effect of in-situ TiB₂ particles on machinability and surface integrity of TiB₂/2024 composite and TiB₂/7075 composite, milling experiments were performed, and compared with conventional 2024 and 7075 aluminum alloys. In-situ TiB₂ particles clustered at the grain boundaries and dispersed inside the matrix alloy grains hinder the dislocation movement of the matrix alloy. Therefore, the milling force and temperature of the composites are higher than those of the aluminum alloys due to the increase of the strength and the decrease of the plasticity. In the milling of composites, abrasive wear is the main wear form of carbide tools, due to the scratching of hard nano-TiB₂ particles. The composites containing in-situ TiB₂ particles have machining defects such as smearing, micro-scratches, micro-pits and tail on the machined surface. However, in-situ TiB₂ particles impede the plastic deformation of the composites, which greatly reduces cutting edge marks on the machined surface. Therefore, under the same milling parameters, the surface roughness of TiB₂/2024 composite and TiB₂/7075 composite is much less than that of 2024 and 7075 aluminum alloy respectively. Under the milling conditions of this experiment, the machined subsurface has no metamorphic layer, and the microhardness of the machined surface is almost the same as that of the material. Besides, compared with 2024 and 7075 aluminum alloy, machined surfaces of TiB₂/2024 composite and TiB₂/7075 composite both show tensile residual stress or low magnitude of compressive residual stress.     

超高强度钢立铣工件温度分析及对加工表面质量的影响

以航空难加工材料300M钢为研究对象,基于立铣加工中的工件温度判断在铣削加工中是否出现了金相组织转变,进而分析不同工况下影响加工表面质量的因素。首先,将移动热源法应用于铣削加工中,计算考虑后刀面磨损的立铣加工工件温度,实验表明,计算值与实验值相比误差在10%以内。然后,分析了工件温度在时间上与空间上的分布,以及不同刀具磨损和加工参数条件下工件表面的温升规律,据此预测加工表面是否出现了组织转变,并结合金相组织观察进一步确认。最后,依据加工表面质量物理层面残余应力和显微硬度的检测数据,初步探讨了各因素对表面质量的影响。结果表明,在研究的加工参数范围内,并未达到金相组织转变温度,表面质量主要受铣削热力作用下的剪切面塑性凸出效应、后刀面挤光效应和热效应的影响。     

Tool Life and Surface Integrity in High-speed Milling of Titanium Alloy TA15 with PCD/PCBN Tools

Titanium alloys are widely used in aeronautics that demand a good combination of high strength, good corrosion resistance and low mass. The mechanical properties lead to challenges in machining operations such as high process temperature as well as rapidly increasing tool wear. The conventional tool materials are not able to maintain their hardness and other mechanical properties at higher cutting temperatures encountered in high speed machining. In this work, the new material tools, which are polycrystalline diamond (PCD) and polycrystalline cubic boron nitride (PCBN) tools, are used in high-speed milling of Ti-6.5Al-2Zr-1Mo-1V (TA15) alloy. The performance and wear mechanism of the tools are investigated. Compared to PCBN tool, PCD tool has a much longer tool life, especially at higher cutting speeds. Analyses based on the SEM and EDX suggest that attrition, adhesion and diffusion are the main wear mechanisms of PCD and PCBN tools in high-speed milling of TA15. Oxidation wear is also observed at PCBN tool/workpiece interface. Roughness, defects, micro-hardness and microstructure of the machined surface are investigated. The recorded surface roughness values with PCD/PCBN tools are bellow 0.3 μm at initial and steady cutting stage. Micro-hardness analysis shows that the machined surface hardening depth with PCD and PCBN tools is small. There is no evidence of sub-surface defects with PCD and PCBN tools. It is concluded that for TA15 alloy, high-speed milling can be carried out with PCD/PCBN tools.     

钛合金TC11深孔钻削刀片材料的选择

在研究了钛舍金材料切削性能的基础上，针对钛合金的特点，选用了五种国内常用的硬质舍金刀片材料，对钛合金进行深孔钻削刀具磨损试验。结果表明，确定了适合钻削钛合金TC11的硬质合金刀片材料。     

微细电解铣削加工模型及实验研究

 对微细电解铣削加工技术进行了深入研究。将分层加工技术应用到微细电解加工过程中,显著改善了加工稳定性;建立了微细电解铣削加工的数学模型;基于电化学刻蚀原理,在线制得直径小至10 μm的圆柱电极;分组实验并验证了加工模型中各参数如：电极直径、加工电压、电解液浓度、铣削层厚度等对微细电解铣削加工精度的影响。通过优化加工参数,成功加工出了深三角结构和四棱台微型腔,形状精度高,加工稳定性好。     

涂层刀具低温铣削SiCp/Al复合材料表面质量研究

在加工过程中,相反的两相特性增加了SiC_p/Al复合材料加工难度,难以获得良好的表面质量。层和TiAlSiN涂层两种铣刀的切削性能。结果表明,在低温条件下,两种刀具的切削力增加,铣削后表面铝基体的开裂及剥落等缺陷均显著改善,加工表面损伤减小且粗糙度降低,低温铣削能获得更好的表面质量。此外,在常温与低温条件下TiAlSiN涂层比TiAlN涂层铣刀的切削力小,低温条件下TiAlSiN涂层铣刀表面完整性和切屑形貌优于TiAlN涂层铣刀。     

涂层刀具铣削加工300M钢的刀具磨损试验研究

建立了一套便携式的在线刀具磨损图像检测装置及相应的计算程序,利用该装置观察到了涂层硬质合金刀具加工300M高强度钢过程的定性磨损规律,并确定了刀具磨损量的测量方法。     

Experimental investigation of rotary sinking electrochemical discharge milling with high-conductivity salt solution and non-pulsed direct current

Electrochemical milling is a modified technique of traditional electrochemical machining (ECM) that can be used to manufacture some helicopter transmission system parts. The use of rotary tools and an inner-jet electrolyte supply pattern can greatly improve the material removal rate (MRR) in a single pass. However, the feed speed is generally limited to minimize the tool wear. To increase the MRR, electrical discharge machining (EDM) is introduced into the electrochemical milling process. The tool rotation is employed to interrupt the discharge and the high-conductivity salt solution and non-pulsed direct current power supply are also adopted to increase ECM, eventually, a new machining method is proposed, which can be called rotary sinking electrochemical discharge milling (RSECD milling). The mechanism of it is explored in this study by analyzing the machined current, MRR, surface morphology, and tool wear at different applied voltages and feed speeds. Besides, the RSECD milling using the tool with a larger diameter is also conducted to further verify the effectiveness. In particular, the MRR can be increased by 742.5% when using the tool with a diameter of 20 mm at the applied voltage of 20 V.     

纤维方向角对超低温冷却石英纤维复合材料铣削性能的影响

石英增强聚酰亚胺树脂基复合材料是一种非均匀的各向异性材料,其加工性能高度依赖于纤维铺层方向与加工进给方向所成角度,即纤维方向角。本文通过一系列不同纤维方向角的干切削和超低温冷却铣削实验,研究了纤维方向角对表面形貌、表面粗糙度、铣削力及刀具磨损的影响。结果表明:不同纤维方向角,剪应力形式不同,切削断屑形式也不同。纤维方向角为锐角时铣削表面质量均良好,但当纤维方向角增大到90°时,切削表面质量下降,切削力变化幅度增大。相同铣削时间内,在干切削工况下,刀具磨损严重,涂层脱落面积约为测量面积的70%;而在低温切削工况下,涂层未遭到严重破坏,刀具仍处于稳定磨损阶段,刀具耐用度优于干切削工况。     

Elliptical vibration cutting of large-size thin-walled curved surface parts of pure iron by using diamond tool with active cutting edge shift

Large-size thin-walled curved surface parts of pure iron are crucial in aerospace, national defense, energy and precision physical experiments. However, the high machining accuracy and surface quality are difficult to achieve due to the serious tool wear and deformation when machining the parts with conventional cutting tools. In this paper, an elliptical vibration cutting (EVC) with active cutting edge shift (ACES) based on a long arbor vibration device is proposed for ultra-precision machining the pure iron parts by using diamond tool. Compared with cutting at a fixed cutting edge, the influence of ACES on the EVC was analyzed. Experiments in EVC of pure iron with ACES were conducted. The evolutions of the surface roughness, surface topography, and chip morphology with tool wear in EVC with ACES are revealed. The reasonable parameters of ultra-precision machining the pure iron parts by EVC with ACES were determined. It shows that the ACES has a slight influence on the machined surface roughness and surface topography. The diamond tool life can be significantly prolonged in EVC of pure iron with ACES than that with a fixed cutting edge, so that high profile accuracy and surface quality could be obtained even at higher nominal cutting speed. A typical thin-walled curved surface pure iron part with diameter ∅240 mm, height 122 mm, and wall thickness 2 mm was fabricated by the presented method, and its profile error and surface roughness achieved PV 2.2 μm and Ra less than 50 nm, respectively.     

GT35硬质合金材料高温摩擦磨损特性研究

利用球-盘高温摩擦磨损试验机对GT35硬质合金进行摩擦磨损实验,研究了GT35硬质合金材料的摩擦磨损特性及机理。分析了不同温度和不同摩擦半径情况下GT35硬质合金的摩擦磨损行为。结果表明:在法向载荷不变的条件下,GT35硬质合金的摩擦系数和比磨损率均随温度的上升而增大,其摩擦系数和比磨损率随摩擦半径的增加也呈上升的变化趋势。     

钛合金TB6铣削表面粗糙度与表面缺陷研究

钛合金TB6铣削表面粗糙度对其使用性能具有重要影响,通过试验研究端面铣削参数、干铣削和刀具磨损对表面粗糙度及表面缺陷的影响。研究表明:表面粗糙度对每齿进给量变化最为敏感,其次是铣削宽度,再次为铣削深度,铣削速度最小;刀具磨损量(VB)对粗糙度产生明显影响,尤其VB大于0.2mm时,表面粗糙度将急剧增加,并导致划痕、孔洞缺陷;不同铣削条件下均存刀痕、侧流、隆起等缺陷;干铣削时加工表面出现熔敷物或熔滴,并增大毛刺;毛刺随切削速度的增大而变小,随刀具磨损量VB的增加而变大。钛合金TB6适宜在冷却润滑条件下低速铣削加工。     

Machining of SiC ceramic matrix composites: A review

Continuous fiber reinforced SiC ceramic matrix composites (FRCMCs-SiC) are currently the preferred material for hot section components, safety–critical components and braking components (in the aerospace, energy, transportation) with high value, and have triggered the demand for machining. However, the high brittleness, anisotropy, and heterogeneity of materials bring great challenges to machining, due to high mechanical and thermal loads, severe tool wear, and poor machining quality. With the increasing demand of FRCMCs-SiC parts, high-quality and high-efficient machining has become a hot issue. This review paper provides a detailed literature survey on the machining of FRCMCs-SiC. The material removal mechanism, defect form, and interfacial mechanical properties of FRCMCs-SiC were summarized. The machining processes of FRCMCs-SiC were introduced, and their respective advantages and disadvantages were compared. Given the low machinability (high hardness, high brittleness, anisotropy, and heterogeneity) of FRCMCs-SiC, preliminary experiments have proved that ultrasonic-assisted machining and laser-assisted machining have shown unique advantages in reducing force and tool wear, improving machining quality and machining efficiency. The machined surface integrity was discussed, the influence of process parameters on the machined surface quality was analyzed, and the machining defects of FRCMCs-SiC were summarized. But for FRCMCs-SiC, the existing quantitative evaluation of the machined surface integrity was weak and unsystematic.     

TC4钛合金侧铣加工表面形貌分析及工艺参数优化

TC4钛合金是 1种典型的不易加工材料,其切削加工表面质量很难控制。为实现面向侧铣加工表面形貌的切削工艺参数优选,开展了 TC4钛合金侧铣加工实验研究。首先,探究了加工表面微观缺陷特征及其形成机制;然后,采用粗糙度参数 Ra和 Sa对铣削表面形貌进行定量表征,并分析了切削速度、进给量和切削深度对表面粗糙度参数的影响;最后,基于遗传算法(Genetic Algorithm,GA)对铣削工艺参数进行了优化。研究发现,加工表面微观缺陷主要有进给刀痕等固有缺陷和黏附颗粒等随机缺陷。铣削表面粗糙度随主轴转速的增大先减小后增大;随径向切深的增大先增大后减小;随进给量先增大后减小。在主轴转速 n = 1 093 r/min、径向切深 ae = 0.2 mm、每转进给量 f = 0.06 mm/r的条件下可以获得较小的表面粗糙度。