High velocity impact characterization of Al alloys for oblique impacts

This paper describes the experimental and computational analyses of a high velocity aluminum projectile impact on an Al6061-T6 spacecraft inner wall at different oblique angles. Al2017-T4 spherical projectiles of 5.56 mm in diameter and 0.25 g in weight were chosen within the velocity range of 1000±200 m/s due to the limitation of the light gas gun. The energy absorbed was calculated by measuring the velocities before and after impact on the inner wall. The energy absorbed by the wall and the remaining energy carried by the projectile helped to estimate the severity of further damage to inner components. Afterwards, validation was done by using the commercially available software LS-DYNA with a dedicated SPH. On average, a 10% energy absorption difference between experimentation and simulation was found. By using C-SCAN, the damage area proportion of the total inner wall to impact penetration hole area was found to be on average 6%, 26% and 53% greater than the projectile cross sectional area for the oblique angle impacts of 30°, 45°, and 60°, respectively. These findings helped to understand the relationship between the oblique impact event and the damage area on a spacecraft inner wall along with space debris cloud propagation and comparison with experimental results using LS-DYNA.     

Characterization of the cataloged Fengyun-1C fragments and their long-term effect on the LEO environment

The intentional breakup of Fengyun-1C on 11 January 2007 created the most severe orbital debris cloud in history. The altitude where the event occurred was probably the worst location for a major breakup in the low Earth orbit (LEO) region, since it was already highly populated with operational satellites and debris generated from previous breakups. The addition of so many fragments not only poses a realistic threat to operational satellites in the region, but also increases the instability (i.e., collision cascade effect) of the debris population there.     

Dynamical evolution of high area-to-mass ratio debris released into GPS orbits

A large set of simulations, including all the relevant perturbations, was carried out to investigate the long-term dynamical evolution of fictitious high area-to-mass ratio (A/M) objects released, with a negligible velocity variation, in each of the six orbital planes used by Global Positioning System (GPS) satellites. As with similar objects discovered in near synchronous trajectories, long lifetime orbits, with mean motions of about 2 revolutions per day, were found possible for debris characterized by extremely high area-to-mass ratios. Often the lifetime exceeds 100 years up to A/M ∼ 45 m²/kg, decreasing rapidly to a few months above such a threshold. However, the details of the evolution, which are conditioned by the complex interplay of solar radiation pressure and geopotential plus luni-solar resonances, depend on the initial conditions. Different behaviors are thus possible. In any case, objects like those discovered in synchronous orbits, with A/M as high as 20–40 m²/kg, could also survive in this orbital regime, with semi-major axes close to the semi-synchronous values, with maximum eccentricities between 0.3 and 0.7, and with significant orbit pole precessions (faster and wider for increasing values of A/M), leading to inclinations between 30° and more than 90°.     

航空发动机高能碎片非包容事件故障树分析

为了使航空发动机高能碎片非包容事件满足适航安全性要求,运用故障树法对航空发动机该事件进行安全性分析并提出了分析方法的步骤和流程。引入最小割集和概率重要的度的概念,利用Isograph Reliability软件画出故障树并计算出高能碎片不包容事件的发生概率、最小割集以及概率重要度,通过对比最小割集和概率重要度,确定导致发动机高能碎片不包容主要的失效形式,并提出了有针对性的措施。     

Physical characterization of the deep-space debris WT1190F: A testbed for advanced SSA techniques

We report on extensive ${\mathit{BVR}}_c{I}_c$ photometry and low-resolution ($\lambda /\mathrm{\Delta }\lambda ～250$) spectroscopy of the deep-space debris WT1190F, which impacted Earth offshore from Sri Lanka, on 2015 November 13. In spite of its likely artificial origin (as a relic of some past lunar mission), the case offered important points of discussion for its suggestive connection with the envisaged scenario for a (potentially far more dangerous) natural impactor, like an asteroid or a comet.Our observations indicate for WT1190F an absolute magnitude $R_c={32.45}_{\pm 0.31}$, with a flat dependence of reflectance on the phase angle, such as ${\mathit{dR}}_c/d?～{0.007}_{\pm 2}$?mag?deg^?1. The detected short-timescale variability suggests that the body was likely spinning with a period twice the nominal figure of $P_{\mathrm{flash}}={1.4547}_{\pm 0.0005}\mathrm{s}$, as from the observed lightcurve. In the ${\mathit{BVR}}_c{I}_c$ color domain, WT1190F closely resembled the Planck deep-space probe. This match, together with a depressed reflectance around 4000 and 8500 Å may be suggestive of a “grey” (aluminized) surface texture.The spinning pattern remained in place also along the object fiery entry in the atmosphere, a feature that may have partly shielded the body along its fireball phase perhaps leading a large fraction of its mass to survive intact, now lying underwater along a tight ($～1\times 80$?km) strip of sea, at a depth of 1500?m or less.Under the assumption of Lambertian scatter, an inferred size of ${216}_{\pm 30}/\sqrt{\alpha /0.1}$?cm is obtained for WT1190F. By accounting for non-gravitational dynamical perturbations, the Area-to-Mass ratio of the body was in the range $(0.006?\mathit{AMR}?0.011)$?m²?kg^?1.Both these figures resulted compatible with the two prevailing candidates to WT1190F’s identity, namely the Athena II Trans-Lunar Injection Stage of the Lunar Prospector mission, and the ascent stage of the Apollo 10 lunar module, callsign “Snoopy”. Both candidates have been analyzed in some detail here through accurate 3D CAD design mockup modelling and BRDF reflectance rendering to derive the inherent photometric properties to be compared with the observations.     

柔性多层冲击空间碎片防护结构设计与试验

充气展开密封结构是未来空间站以及大型空间居住舱的理想构建形式,其外蒙皮由气密层、增强层、微流星体和空间碎片防护层、辐射保护层以及热控层组成。为了既满足对空间碎片的防护,又满足折叠、收纳以及展开的要求,空间碎片防护层需要采用多层冲击防护结构设计。基于多层冲击防护结构,采用国产的玄武岩纤维材料和芳纶织物的特性参数,根据弹道极限方程设定了柔性空间碎片防护层的设计参数,并通过高速撞击试验对根据设计参数生产的试验件进行了试验验证,试验结果与柔性多层冲击防护结构的弹道极限方程吻合较好。     

天基激光移除空间碎片仿真平台研究与开发

为了从空间碎片和天基移除系统两方面分析激光驱动碎片变轨过程,优化移除任务规划和策略,基于真实的可观测空间碎片数据,设计并开发了一套天基激光移除空间碎片三维数值仿真平台。首先从总体设计出发,对三维数值仿真平台的需求分析、总体框架、模块功能进行了明确的描述。其次通过对激光驱动空间碎片变轨过程数学模型的分析,确定了各模块的具体实现方法。最后采用C++/Qt开发了三维数值仿真平台,通过仿真验证了设计平台的有效性。该仿真平台可用于不同天基平台和目标碎片的任务规划、碎片分布热点区域和航天器防护区域的方案设计及空间环境治理体系的优化设计。     

Characterizing space debris longitude-dependent distribution based on RAAN perturbation rate

The space debris environment is one of the major threats against payloads. Space debris orbital distribution is of great importance for space debris environment modeling. Due to perturbation factors, the Right Ascension of Ascending Node (RAAN) of space objects changes consistently, causing regular rotation of the orbit plane around Earth’s axis. Based on the investigation of the RAAN perturbation rate of concerned objects, this paper proposes a RAAN discretization method in order to present the space debris longitude-dependent distribution. Combined with two line element (TLE) data provided by the US Space Surveillance Network, the estimated value from RAAN discretization method is compared with the real case. The results suggest that using only the initial orbital data at the beginning of the time interval of interest, the RAAN discretization method is able to provide reliable longitude distribution of concerned targets in the next following period. Furthermore, spacecraft cumulative flux against space debris is calculated in this paper. The results suggest that the relevance between spacecraft RAAN setup and flux output is much smaller for LEO targets than MEO targets, which corresponds with the theory analysis. Since the nonspherical perturbation is the major factor for RAAN variation, the RAAN perturbation rate has little connection with the size of orbital objects. In other words, the RAAN discretization method introduced in this paper also applies to space debris of different size range, proposing a possible suggestion for the improvement of space debris environment engineering models.     

空间碎片失效概率分析软件标准的校验

空间碎片失效概率分析软件是“空间碎片防护设计软件包”的重要组成部分。文章简单介绍了失效概率分析软件的组成结构,并根据国际标准对失效概率分析软件进行详细校验。