后掠翼三维鼓包串激波控制参数的影响

针对跨声速后掠翼,三维鼓包串作为一种有效的减阻方式具有结构简单、高效及鲁棒性好等优点.利用全局优化算法探索了鼓包设计参数空间的整体特性,并对鼓包长度、三维鼓包展向设计参数对鼓包减阻效果的影响进行了研究,发现鼓包顶点位置和高度对阻力系数最敏感,三维鼓包的展向设计参数则对阻力系数不敏感,而鼓包长度和鼓包相对展长越长越有利于减阻.在此基础上开展了小后掠角自然层流机翼加3种不同类型鼓包串的优化研究,通过优化结果发现,增加优化后的三维鼓包串,可将小后掠角自然层流机翼阻力发散马赫数向后推移,并且鼓包平均长度和控制区越大,效果越好.三维鼓包串具有良好的局部控制特性,可用于局部较强激波的抑制.三维鼓包串对常规后掠翼波阻具有良好的控制效果,同时能够抑制激波诱导的机翼后缘气流分离.      

翼吊短舱形式发动机安装效应的风洞试验研究

为了确定实际飞行使用条件下,发动机状态变化时,进排气系统损失对飞机气动特性的影响,本文针对翼吊短舱形式的发动机开展了缩比模型风洞试验,分别进行了基本构型与起飞构型下,马赫数0.1、0.15、0.2,攻角0°~15°变化,5种不同发动机状态条件下的风洞试验,通过数据分析,明确了该类型发动机推/阻力划分的基本方法,分析了发动机状态变化时飞机气动特性的改变及修正方法。风洞试验结果表明：发动机状态变化对飞机升阻特性影响明显,飞机设计研发阶段不能仅对短舱通流模型,或单一发动机状态下的动力短舱模型进行损失修正,必须建立合理的推/阻划分体系,对实际使用条件下,发动机状态变化引起的进排气损失进行修正。     

共轴式直升机桨毂阻力特性与减阻试验

共轴式直升机桨毂阻力占全机废阻的50%以上,因此有必要对桨毂阻力特性和减阻设计进行研究。 通过对某共轴式直升机桨毂模型、减阻方案及减阻方案加装涡流发生器进行风洞试验,研究轴式直升机桨毂的 阻力特性,验证减阻方案及减阻方案加装涡流发生器的减阻效果。结果表明:桨毂支臂方位角、转速和攻角变 化对桨毂及其减阻方案的阻力影响很小;上下桨毂整流罩与中间轴整流罩之间的缝隙对阻力影响比较大;减阻 方案可以降低约33%的桨毂阻力,而加装涡流发生器的减阻效果并不明显。     

翼尖装置优化设计研究

使用面元法气动分析软件VSAERO对机翼与翼梢小翼组合体模型进行数值模拟,并采用Steve Smith提出的诱导阻力优化方法对翼梢小翼的定位进行优化设计。结果表明,能够有效地预测出翼梢小翼的最优定位,在翼梢小翼优化设计中具有很好的适用性。     

简化微小液滴在超声速气流横向喷射中的运动探索

从研究超声速气流中简化液滴(刚性小球)的气动力着手,比较分析使用CFD方法与使用两相流理论中已有的颗粒阻力系数模型得到的简化液滴气动力结果,得出Charles B.Henderson给出的阻力系数经验关系式适用于计算简化液滴在超声速气流中的运动。进一步,对不同直径简化液滴的运动开展工程方法的计算。在来流Ma=2.7的二维平板超声速流场中选取一个截面,作为气相流场,结果显示:(1)简化液滴与主气流存在相对超声速运动,当简化液滴直径dk≤0.12mm时,纵向相对超声速运动区域约为0.15m~0.4m,当dk0.12mm时,作用区域明显增大;(2)以10m/s喷射出的简化液滴,其横向穿透深度与纵向运动距离比约为0.004m/1m~0.021m/1m;(3)以100m/s的速度喷射出的30~120μm直径简化液滴,其横向穿透深度与纵向运动距离比约为0.02m/1m~0.055m/1m,实际过程中,小尺寸简化液滴的汽化很快,其穿透深度很小。     

风力机组叶片的先进翼型族设计

大型风力机组叶片设计需要专用的翼型族,以满足风力机组运行的环境要求。高升阻比、低粗糙度影响是该翼型族的气动性能特点。为了发展我国具有自主知识产权的风力机专用翼型族,在科技部863项目的支持下,北京航空航天大学联合国内气动研究单位,通过理论分析、数值模拟和风洞试验等技术途径,开发了两个适用于大型风力机组叶片的先进翼型族。理论分析和风洞试验表明,设计结果基本达到了预先设定的气动性能指标。     

水气动量交换的实验研究

在风浪槽中进行水气动量交换实验，测量了不同风速和风区下的波浪及空气湍流流场。测量数据表明水面上风速分布符合对数律，水气界面附近在小范围的动量交换常通量层。阻力系数ＣＤ随风速增加线性增长，随波龄增加而减小。这一趋向与理论分析及外海帝测结果一致。对风浪发展过程中波浪和空气湍流谱结构的分析证明了水气运动的耦合关系。     

Refining DORIS atmospheric drag estimation in preparation of ITRF2008

In preparation of ITRF2008, all geodetic technique services (VLBI, SLR, GPS and DORIS) are generating new solutions based on combination of individual analysis centers solutions. These data reprocessing are based on a selection of models, parameterization and estimation strategy unique to each analysis center and to each technique. While a good agreement can be found for models between groups, thanks to the existence of the IERS conventions, a great diversity still exist for parameter estimation, allowing possible future improvements in this direction. The goal of this study is to focus on the atmospheric drag estimation used to generate the new DORIS/IGN ignwd08 time series prepared for ITRF2008. We develop here a method to inter-compare different processing strategies. In a first step, by analyzing single-satellite solutions for a few weeks of data but for a large number of possible analysis strategies, we demonstrate that estimating drag coefficient more frequently (typically every 1–2 h instead of previously every 4–8 h) for the lowest DORIS satellites (SPOTs and Envisat) provides better geodetic results for station coordinates and polar motion. This new processing strategy also solved earlier problem found when processing DORIS data during intense geomagnetic events, such as geomagnetic storms. Differences between drag estimation strategies can mostly be found during these few specific periods of extreme geomagnetic activity (few days per year). In such a case, when drag coefficient is only estimated every 6 h or less often for single-satellite solution, a significant degradation in station coordinate accuracy can be observed (120 mm vs. 20 mm) and significant biases arose in polar motion estimation (5 mas vs. 0.3 mas). In a second step, we reprocessed a full year of DORIS data (2003) in a standard multi-satellite mode. We were able to provide statistics on a more reliable data set and to strengthen these conclusions. Our proposed DORIS analysis is easy to implement in all software packages and is now already used by several analysis centers of the International DORIS Service (IDS) when submitting reprocessed solutions for ITRF2008.     

A novel approach for predicting inlet pressure of aircraft hydraulic pumps under transient conditions

Cavitation caused by insufficient suction is a major factor that influences the life of aircraft pumps. Currently, pressurizing the tank can solve the cavitation problem under steady large-flow conditions. However, this method is not always effective under transient conditions (from zero flow to full flow in a very short time). Moreover, to apply and design other measures, such as a boost impeller, the suction dynamics during the transient period must be investigated. In this paper, a novel approach based on the pressure wave propagation theory is proposed for predicting the inlet pressure of an aircraft pump under transient conditions. First, a dynamic model of a typical aircraft pump is established in the form of differential equations. Then, the transient flow model of the inlet line is described using momentum and continuity equations, and the governing equations are discretized by the method of characteristics and the finite difference method. The simulated results are in good agreement with the results from verification tests. Further simulation analysis indicates that the wave velocity and transient time may influence the inlet and reservoir pressure as well as the size of the inlet line. Finally, solutions for upgrading the inlet pressure are discussed. These solutions provide guidelines for designing inlet installations.     

Reconfigurable Flight Control Design for Combat Flying Wing with Multiple Control Surfaces

With control using redundant multiple control surface arrangement and large-deflection drag rudders,a combat flying wing has a higher probability for control surface failures.Therefore,its flight control system must be able to reconfigure after such failures.Considering three types of typical control surface failures(lock-in-place(LIP),loss-of-effectiveness(LOE) and float),flight control reconfiguration characteristic and capability of such aircraft types are analyzed.Because of the control surface redundancy,the aircraft using the dynamic inversion flight control law already has a control allocation block.In this paper,its flight control configuration during the above failures is achieved by modifying this block.It is shown that such a reconfigurable flight control design is valid,through numerical simulations of flight attitude control task.Results indicate that,in the circumstances of control surface failures with limited degree and the degradation of the flying quality level,a combat flying wing adopting this flight control reconfiguration approach based on control allocation could guarantee its flight safety and perform some flight combat missions.