基于互锁双指令控制的电磁阀驱动电路设计

为满足体积及重量强约束条件下的动力系统电磁阀控制需求，提出了一种基于互锁双指令控制的电磁阀驱动电路设计方案。采用逻辑相反的互锁指令与串并联设计的阀门驱动电路结构形式，设计了基于McBSP内总线交互的电磁阀控制流程，建立了150N电磁阀驱动电路仿真模型及阀门电流测试平台。仿真及测试结果表明，该驱动电路能够有效实现二度故障下的电磁阀开启与关闭。     

A novel architecture of electro-hydrostatic actuator with digital distribution

To address the flow imbalance rapidly of the asymmetric Electro-Hydrostatic Actuator (EHA), this paper presents a novel architecture of asymmetric EHA with the Digital Distribution (EHA-DD). It also improves the flow nonlinearity and control accuracy of the pump, especially in the low-speed condition. The digital distribution with two High-Speed on–off Valves (HSVs) not only balances flow instead of the check valves, but also replaces the pump at the low-speed to control output flow by adjusting the PWM signal. The pump and HSVs are the crucial components to control flow output. Firstly, the flow calculation models of the pump and the duty ratio inversed model of the HSV are obtained through experimental tests and the identification method. To get the control input signal for the required flow, the pump speed and PWM duty ratio for the HSVs are inversed to compensate for flow output. Further, a multimode digital flow distribution control method based on pump speed, mainly including the pump-controlled mode for large flow demand and valve-controlled mode for little flow demand, is proposed to control the accurate flow output actively. The step extension experiments based on the flow calculation models are conducted on the EHA-DD prototype under elastic, opposite varying load. The results demonstrate that the EHA-DD realizes little position error by accurate flow control, and it is also beneficial to improve the service life of the pump.     

A novel framework for liquid propellant engine’s cooling system design by sensitivity analysis based on RSM and multi-objective optimization using PSO

One of the challenges of combustion chamber and nozzle design in a Liquid Propellant Engine (LPE) is to predict the behavior and performance of the cooling system. Therefore, while designing, the optimization of the cooling system is always of great importance. This paper presents the multi-objective optimization of the LPE’s cooling system. To this end, a novel framework has been developed, resulting from the application of the Response Surface Method (RSM) and the correlation coefficients matrix, sensitivity analysis and the The Particle Swarm Optimization (PSO). based on this method, the input variables, constraints, objective functions, and their surfaces were identified. In terms of multi-optimization algorithms, RSM and PSO are utilized to get global optimum. In conclusion, the methodology capability is to optimize the LPE’s cooling system, 6 percentage increase in total heat transfer and 7 bar decrease cooling system pressure loss, which resulted in a 1.2-seconds increase in the specific impulse of the engine.     

发动机喷流对飞行器底部流动影响数值模拟

针对发动机燃气喷流对底部流动的影响开展研究。建立冷喷与热喷计算方法，与经典的高压空气尾喷管喷流试验数据进行了对比，验证了本文建立的三维喷流方法的可靠性。对本文选用的飞行器外形采用冷喷与热喷方法开展了对比计算并与飞行试验值进行比较，分析了两种方法结果的差异。采用热喷方法对来流马赫数 2.5 ，不同飞行高度及喷管进口总压开展计算，研究飞行高度及喷管进口总压对发动机喷流及底部流场的影响。结果表明，保持飞行高度、来流马赫数不变，喷管进口总压增加，底部压力系数逐渐提高。燃气质量浓度最大值位于底部空腔的壁面处，且保持一个恒定值。保持喷管进口总压、来流马赫数不变，飞行高度增加，喷流高速区向后移动且中心区最大马赫数增加。在一定飞行高度下，底部压力系数由负转正，即飞行器底部会出现正推力，这对飞行器的射程会产生重要影响，需要提前评估。     

西安某粘接材料厂室内供暖、热水系统的设计

基于厂方对供热系统的要求,根据供热建筑物、机房和可利用设施的实际情况,采用一台换热器,通过阀门的切换,实现了供暖和供热水的分段运行。将蒸汽发生器的进水与系统补水有机地整合为一个系统,有效地解决了机房面积过小的实际困难。利用自来水的压力和热水箱与浴室的高差解决了热水供应的实际问题。     

SAR performance-based fault diagnosis for electro-hydraulic control system: A novel FDI framework for closed-loop system

Model-based fault diagnosis serves as an efficient and powerful technique in addressing fault detection and isolation (FDI) issues for control systems. However, the standard methods and their modifications still encounter some difficulties in algorithm design and application for complex higher-order systems. To avoid these difficulties, a novel fault diagnosis framework based on multiple performance indicators of closed-loop control system is proposed. Under this framework, a so-called performance residual vector is constructed to measure the differences between the real system and the nominal model in terms of system stability, accuracy, and rapidity (SAR) respectively. The criteria for quantification, normalization of the SAR residuals and the explicit mappings between the thresholds and the required performance are given. FDI can be easily achieved simultaneously by monitoring the normalized residual vector length and direction in the SAR performance residual space. A case study on electro-hydraulic servo control system of turbofan engine is adopted to demonstrate the effectiveness of the proposed method.     

航空发动机设计中采用CAD技术的研究

为了进一步加强ＣＡＤ（ＣｏｍｐｕｔｅｒＡｉｄｅｄＤｅｓｉｇｎ）技术在航空发动机设计领域的应用,主要介绍ＡｕｔｏＣＡＤ图形软件的辅助绘图、三维建模的功能及在航空发动机领域的一些应用。目的是在航空发动机设计领域推广及运用ＣＡＤ技术改善发动机的设计方法。     

航天器推进系统故障诊断专家系统的研制开发

论述了设计航天器推进系统故障监测与诊断专家系统的重要性和必要性。并结合具体工程背景所研制开发的诊断系统, 研究了其主要的设计思想、特点、功能以及软件需求分析,实现软／硬件环境     

涡扇发动机气路故障定量诊断的BP网络研究

为了克服ＢＰ算法收敛速度慢的问题,提出了一种基于混合学习规则的ＢＰ算法,并采用模归一化方法,成功地定量组织了故障的学习样本,建立了能够定量分析发动机气路部件故障的人工神经网络（ＢＰＮ）。通过分析测量系统随机误差的影响和实际试车数据的效验结果,表明该网络具有较强的推广能力及适应性,能基本满足故障定量诊断的要求,并具有较好的工程实用性。     

应用BP-ART混合神经网络的推进系统状态监控实时系统

应用ＢＰ－ＡＲＴ混合神经网络提出了一种供推进系统状态监控实时使用的系统,其拓扑结构为： 第一层处理单元由ＢＰ神经网络组成, 每个ＢＰ网络代表一个相应的推进系统组件; 第二层处理单元为一个ＡＲＴ神经网络, 网络的每一个输出代表推进系统的一种“健康状态”, 据此可对其故障进行“诊断”。该混合结构充分发挥了两类网络的优点, 给出的具体应用实例也显示出在推进系统实时状态监控与故障诊断应用中的有效性