运载火箭姿态系统自适应神经网络容错控制

针对运载火箭姿态系统跟踪问题,考虑干扰、执行器故障和模型不确定因素的影响,设计了一种基于自适应神经网络的非线性容错控制律。该控制算法结合了连续的终端滑模控制,径向基神经网络和自适应控制方法。首先,基于滑模控制理论,设计了一种快速终端滑模面,保证系统跟踪误差能够在有限时间收敛至零。然后,在终端滑模面基础上,提出了一种基于自适应径向基神经网络估计的终端滑模控制律。利用自适应参数的神经网络逼近系统参数并提高抗干扰性能,采用平滑连续控制策略消除了终端滑模中的颤动现象。通过李雅普诺夫的分析方法证明了闭环系统的收敛性和全局稳定性。采用数值仿真,验证了提出的基于自适应径向基神经网络的终端滑模控制律具有较好的跟踪性能和精度。     

双拦截弹拦截单目标边界型微分对策制导律研究

针对战术弹道导弹、高超声速巡航导弹和无人飞行器等新型具有高机动性能的防空目标,为提高成功拦截的概率,采用多枚拦截弹进行拦截。应用微分对策理论,将双拦截弹拦截单目标的末段制导问题建模为“二对一追踪-逃逸”对策模型。考虑最大加速度约束,研究了两枚拦截弹的拦截空间分解和对策空间分布,并通过仿真研究了制导律性能。结果表明：采用两枚拦截弹拦截时,脱靶量对目标机动方向的转变时间具有很好的鲁棒性。     

焊接过程电信号在线监测研究现状及发展趋势

详细介绍了各种在线监测和分析方法在焊接过程电信号监测以及焊接质量评估中的应用，分析每一种在线监测方法的特点和焊接质量方面的应用现状。对各种在线监测方法在焊接质量监测中应用的发展趋势进行了分析和预测。     

Numerical analysis and optimization of boundary layer suction on airfoils

Numerical approach of hybrid laminar flow control(HLFC) is investigated for the suction hole with a width between 0.5 mm and 7 mm. The accuracy of Menter and Langtry’s transition model applied for simulating the flow with boundary layer suction is validated. The experiment data are compared with the computational results. The solutions show that this transition model can predict the transition position with suction control accurately. A well designed laminar airfoil is selected in the present research. For suction control with a single hole, the physical mechanism of suction control, including the impact of suction coefficient and the width and position of the suction hole on control results, is analyzed. The single hole simulation results indicate that it is favorable for transition delay and drag reduction to increase the suction coefficient and set the hole position closer to the trailing edge properly. The modified radial basis function(RBF) neural network and the modified differential evolution algorithm are used to optimize the design for suction control with three holes. The design variables are suction coefficient, hole width, hole position and hole spacing. The optimization target is to obtain the minimum drag coefficient. After optimization,the transition delay can be up to 17% and the aerodynamic drag coefficient can decrease by 12.1%.     

Flow separation control on swept wing with nanosecond pulse driven DBD plasma actuators

A 15° swept wing with dielectric barrier discharge plasma actuator is designed.Experimental study of flow separation control with nanosecond pulsed plasma actuation is performed at flow velocity up to 40 m/s. The effects of the actuation frequency and voltage on the aerodynamic performance of the swept wing are evaluated by the balanced force and pressure measurements in the wind tunnel. At last, the performances on separation flow control of the three types of actuators with plane and saw-toothed exposed electrodes are compared. The optimal actuation frequency for the flow separation control on the swept wing is detected, namely the reduced frequency is 0.775, which is different from 2-D airfoil separation control. There exists a threshold voltage for the low swept wing flow control. Before the threshold voltage, as the actuation voltage increases, the control effects become better. The maximum lift is increased by 23.1% with the drag decreased by 22.4% at 14°, compared with the base line. However, the best effects are obtained on actuator with plane exposed electrode in the low-speed experiment and the abilities of saw-toothed actuators are expected to be verified under high-speed conditions.     

星外管路多层隔热组件热参数确定方法

提出了利用整星热平衡试验数据确定星外管路多层组件热参数的方法,解决了以往星外管路热设计在地面热试验验证不充分的难题。以某卫星星外管路为例,通过对星外管路试验状态模型的修正,确定了星外管路多层隔热组件热参数,并分析了星外管路的在轨极端温度。根据确定的星外管路多层隔热组件热参数计算出的星外管路温度,与在轨温度数据符合较好,验证了此方法的有效性。     

Dynamic analysis of C/C composite finger seal

A seal device as an important component of aeroengines has decisive influence on per- formance, reliability, and working life of aeroengines. With the development of aeroengines, demands on the performance characteristics of seal devices are made strictly. Finger seal as a novel kind of sealing device, recently attracts more and more attentions in academic circles and engineer- ing fields at home and abroad. Research on finger seals has been extensively developed, especially on leakage and wear performances under dynamic conditions. However, it is a pity that the work on finger seals has been limited with a single approach that is improving the performance by structural optimization; in addition, the technology of dynamic analysis on finger seals is weak. Aiming at the problems mentioned above, a distributed mass equivalent dynamic model of finger seals considering the coupling effect of overlaid laminates is established in the present paper, the dynamic perfor- mance of 2.5 dimension C/C composite finger seal is analyzed with the model, and then the effects of fiber bundle density and fiber bundle preparation direction on finger seal＇s dynamic performance are discussed, as well as compared with those of Co-based alloy finger seal. The current work is about dynamic analysis of finger seals and application of C/C composite in this paper may have much academic significance and many engineering values for improving research level of finger seal dynamics and exploring feasibility of C/C composite being used for finger seals.     

多种失效模式相关的机构运动可靠度计算方法

机构运动中必然存在多种相关失效模式,多为影响机构运动的各类随机变量函数.为了在机构运动可靠性分析中有效考虑多种相关失效模式的影响,建立了考虑多种失效模式相关条件下的机构运动可靠度计算模型,并实现了对多种失效模式相关条件下的机构运动可靠度计算模型的求解,为考虑多种相关失效模式下的机构运动可靠性分析提供了一种有效途径.以6408滚动轴承为例,进行100 000抽样计算,考虑失效模式相关条件下运动可靠度为95.998 9%.该方法精度较高,具有一定的理论意义和应用价值.     

碳硼复合渗研究及其应用

本文研究了２０钢和４５钢的碳硼复合渗渗层组织及耐磨性能。结果表明：复合渗可得到较强支撑作用的过渡层，从而使渗硼层耐磨性提高。饲料粉碎机锤片采用复合渗工艺处理后试用效果良好。     

数控纤维缠绕机芯模处理软件的研究

给出了离散点输入芯模的数学处理过程，从而对任意给定的芯模轮廓曲线有了统一的处理方法，统了一芯模输入，为非测地线缠绕软件的输入芯模“微元化”提供了理论依据，并为后面的缠绕计算奠定了基础。