一种基于OPTICS聚类的仅测角导航目标检测算法

仅测角自主导航方法具有设备简单、复杂度低，功耗低的优点，在空间任务中具有广泛的应用前景.针对中远距离下空间目标特征少的特点，提出了一种利用基于OPTICS聚类算法的空间目标检测方法，可用于仅测角导航过程中的目标检测.对原始星图进行预处理提取星点及目标点，并结合星图识别的结果选择部分帧，使用经过改进的OPTICS聚类方法获得目标运动轨迹.最后，使用本文中的算法对软件仿真出的含有目标的高精度星图进行处理验证了算法的可行性.在卫星相对于空间目标抵近过程中，目标检测的水平误差及垂直误差小于0.15°的帧数分别占到了85.4%以及99.6%.相比AVANTI实验中的目标检测方法，减少了在轨任务中相关参数的调节，进一步提升了算法的自主性.     

低温锂离子电池研究进展

随着能源需求的日益高涨，锂离子电池（LIB）在各个领域内的应用愈发广泛。为满足极端气候等特殊应用环境对储能器件的需求，LIB需拓宽其工作温度范围。从材料和电池结构角度详细总结了应用于低温条件LIB的最新研究进展。首先，分析了限制LIB低温性能的根本原因；然后，分别从电解液的研发与优化、电极材料的改性和开发、新型电池体系的开发、电池热管理系统（BTMS）设计4个方面归纳并讨论了在低温情况下改善LIB性能的途径和方法；最后，总结了低温LIB研究亟待解决的问题，并为新一代低温LIB的发展提出了可行的研究方向。      

纤维织物超高速碰撞热-力学模型与分析

A new thermo mechanical model for fiber fabric of hypervelocity impact is established by using the Johnson Cook model, the Gruneisen equation of state and the FEM SPH coupling algorithm, while some new factors are taken into account such as the heat generation, strain rate strengthening and high temperature softening of materials. Mechanical and thermal information could be obtained with the model, such as penetration, fragmentation, stress and strain, heat generation and temperature field of fiber fabric. The analysis results are in good agreement with the experimental results.     

飞秒激光系统图像调焦装置以及方法

飞秒激光直写技术在复杂三维微结构加工领域具有显著优势，而调焦是否精准直接影响了所加工结构的完整度.提出了在光路中临时置入调焦光源和物的图像调焦技术，通过调节物的位置使其成像面与激光聚焦面一致，从而通过清晰可分辨的成像状态间接反映激光聚焦状态.利用Zemax软件模拟分析了原飞秒激光光路与加入调焦光源和物的调焦光路，二者可实现相同加工物镜后工作距离与良好成像质量，证明了该方法的可行性.通过分析得到该过程的成像误差主要由成像镜头焦深(3.9 μm)引起，我们获得的理想调焦精度可达到1/2焦深以内.设计了单层高度为5 μm的二层圆柱结构，通过多次实验验证了所加工元件高度误差在1.5 μm范围以内，与理论分析一致，满足飞秒激光系统的调焦要求.     

Ground experiments of Chang’e-5 lunar regolith penetrating radar

The Lunar Regolith Penetrating Radar (LRPR) is an Ultra-Wideband (UWB) array-based Ground penetrating radar (GPR) onboard the lander of Chang’e-5 (CE-5) mission. The primary scientific objectives of the LRPR are to probe the thickness and structure of lunar regolith of the landing site, and support the drilling and sampling process. In order to evaluate the performance of the LRPR, a series of ground experiments are performed using the LRPR prototype mounted on a CE-5 lander model. The performance of the LRPR is evaluated by comparing the experimental data with the simulated data. Data processing and imaging method are verified, and the interferences from the lander and other aspects are analyzed. The results of the ground experiments and simulation demonstrate that the LRPR is able to meet the design requirement of 2-m detection depth. They also indicate that the upper and lower interfaces of the stratified structure in the lunar regolith can be well distinguished by the LRPR when the dielectric constant difference is greater than 0.3, and the imaging effect of the location under the dense antennas is better than that of other positions. However, the identification capability of the LRPR to the independent blocky objects is relatively poor mainly due to the clutters caused by the lander, the sparsity of the antenna elements compared to the size of the basalt block, the limited aperture of the antenna array, and the tail of the transmitted waveform.     

Modeling and Optimal Design of Planar Linkage Mechanism of Coupled Joint Clearances for Manufacturing

The uncertainty of the mechanism motion error is mostly caused by the manufacturing process,so the motion error cannot be effectively predicted at the design phase.The problems of manufacturing complexity and the relationship between design and manufacturing are analyzed,and the influence of dimensional tolerance and fit tolerance on the motion accuracy of the system is considered in the design process.Then based on the Monte Carlo simulation,an optimal design model of planar linkage mechanism is set up.A typical offset slider-crank mechanism is used as an illustrative example to carry out the optimal design.Compared with the result of typical robustness design,the similar variation characteristics of the mean value and the standard deviation can be found,so the proposed method is effective.The method is furthermore applied in the optimization of the schemes with different fit tolerances and the prediction of motion errors in the design phase is achieved.A set of quantitative evaluation system for mechanism optimal design is provided.Finally,a basic strategy is presented to balance the motion precision and manufacturing cost.     

天基轻气炮发射清除低轨碎片方案及关键技术分析

文章分析了现有的空间碎片清除方式,并以800~1200 km低地球轨道高度上1~10 cm量级的空间碎片为清除目标,提出了天基轻气炮清除碎片的新方法。首先分析了轻气炮有效载荷在典型参数下的弹丸加速能力;之后根据将碎片降轨使其坠入大气层烧毁的设想,提出天基轻气炮共面清除碎片的方式,并选择轨道高度800 km的圆轨道作为碎片运行轨道进行可行性分析。计算表明,对半径10 cm、厚度1 cm的铝合金圆板碎片(质量211.95 g),使用初速1 km/s、重10 g的黏性弹丸可按任务方案达到清除效果。此外,计算出该参数弹丸对轨道高度800~1200 km的圆轨道上可清除的最大碎片质量为500~825 g,证明轻气炮弹丸对1~10 cm的碎片具有较强的清除能力。最后,分析了以轻气炮为有效载荷的航天器在完成清除碎片任务时的关键技术。     

三维自适应终端滑模协同制导律

针对多枚导弹协同作战的问题,且多枚导弹之间保持有向拓扑通信的条件下,基于终端滑模法设计了视线方向及视线法向的双层协同制导律。其中,视线方向的制导指令能够保证导弹同时完成拦截任务;视线法向上的三维制导律能够保证每枚导弹以期望的视线角攻击目标,从而发挥各枚导弹的最大杀伤力,并且视线角的约束相当于规划了末制导段导弹的弹道问题,在一定程度上避免攻击目标前导弹间发生碰撞。同时,针对所设计的滑模制导律设计了新的自适应律,从而加快了滑模面的收敛速度并且削弱了由符号函数引起的系统抖振现象。基于李雅普诺夫稳定性理论,证明了所设计制导律的正确性,并在最后给出了数学仿真实验,验证了所设计制导律的有效性及优越性。     

Numerical analysis and optimization of boundary layer suction on airfoils

Numerical approach of hybrid laminar flow control(HLFC) is investigated for the suction hole with a width between 0.5 mm and 7 mm. The accuracy of Menter and Langtry’s transition model applied for simulating the flow with boundary layer suction is validated. The experiment data are compared with the computational results. The solutions show that this transition model can predict the transition position with suction control accurately. A well designed laminar airfoil is selected in the present research. For suction control with a single hole, the physical mechanism of suction control, including the impact of suction coefficient and the width and position of the suction hole on control results, is analyzed. The single hole simulation results indicate that it is favorable for transition delay and drag reduction to increase the suction coefficient and set the hole position closer to the trailing edge properly. The modified radial basis function(RBF) neural network and the modified differential evolution algorithm are used to optimize the design for suction control with three holes. The design variables are suction coefficient, hole width, hole position and hole spacing. The optimization target is to obtain the minimum drag coefficient. After optimization,the transition delay can be up to 17% and the aerodynamic drag coefficient can decrease by 12.1%.