Switching and performance variations of on-orbit BDS satellite clocks

The information of the satellite clock switching and performance variations on-orbit of Chinese BeiDou-2 Navigation System (BDS) is not available for the public. In order to detect the BDS satellite clock switching and performances variation, we analyzed the precise clock offset products with a total duration of 5?years every BDS satellite equipped four atomic clocks from four different manufactures from January 2013 to October 2017. Three important contributions are concluded as follows. (1) It is found that the average time of on-orbit operation for BDS satellite clocks is about 1–2?years. There have been 22 times of clock switching for BDS satellites, of which the C05 and C08 satellites have been switched to the fourth (last) atomic clock. (2) There are frequent phase adjustments for BDS on-orbit satellite clocks, and the frequency series is relatively stable. Furthermore, there are semi-annual sinusoid cycles in the frequency drift series of C06 and C09 satellites. (3) The performances of MEO satellite clocks perform better than the IGSO and GEO satellite clocks. The average ten-thousand frequency stability of BDS satellite clocks is about 1E-13, which is worse than that of GPS and Galileo but better than that of GLONASS.     

The adjusted optical properties for Galileo/BeiDou-2/QZS-1 satellites and initial results on BeiDou-3e and QZS-2 satellites

Solar Radiation Pressure (SRP) is the dominant non-gravitational perturbation for GNSS (Global Navigation Satellite System) satellites. In the absence of precise surface models, the Empirical CODE Orbit Models (ECOM, ECOM2) are widely used in GNSS satellite orbit determination. Based on previous studies, the use of an a priori box-wing model enhances the ECOM model, especially if the spacecraft is a stretched body satellite. However, so far not all the GNSS system providers have published their metadata. To ensure a precise use of the a priori box-wing model, we estimate the optical parameters of all the Galileo, BeiDou-2, and QZS-1 (Quasi Zenith Satellite System) satellites based on the physical processes from SRP to acceleration. Validation using orbit prediction proves that the adjusted parameters of Galileo and QZS-1 satellites exhibit almost the same performance as the corresponding published and “best guess” values. Whereas, the estimated parameters of BeiDou-2 satellites demonstrate an improvement of more than 60% over the initial “guess” values. The resulting optical parameters of all the satellites are introduced into an a priori box-wing model, which is jointly used with ECOM and ECOM2 model in the orbit determination. Results show that the pure ECOM2 model exhibits better performance than the pure ECOM model for Galileo, BeiDou-2 GEO and QZS-1 orbits. Combined with the a priori box-wing model the ECOM model (ECOM+BW) results in the best Galileo, BeiDou-2 GEO and QZS-1 orbits. The standard deviation (STD) of satellite laser ranging residuals reduce by about 20% and 5% with respect to the pure ECOM2 model for Galileo and BeiDou-2 GEO orbits, while the reductions are about 40% and 60% for QZS-1 orbits in yaw-steering and orbit-normal mode respectively. BeiDou-2 IGSO and MEO satellite orbits do not benefit much from the a priori box-wing model. In summary, we suggest setting up a unified SRP model of ECOM+BW for Galileo, QZS-1, and BeiDou-2 orbits based on the adjusted metadata. In addition, we estimate the optical parameters of BeiDou-3e and QZS-2 satellites using a limited number of tracking stations. Results regarding the unified SRP model indicate the same advantages, the STD of satellite laser ranging residuals reduces by about 30% and 20% for QZS-2 and BeiDou-3e orbits respectively over orbit products without a priori model. The estimation procedure is effective and easy to apply to the new emerging satellites in the future.     

Preliminary analysis of the quality and positioning performance of BDS-3 global interoperable signal B1C&B2a

BeiDou-3 Navigation Satellite System (BDS-3) satellites are equipped with the new generation GNSS signals B1C and B2a, which support the interoperability with GPS and Galileo systems. In this study, the pseudo-range multipath error and carrier phase observation noise of the BDS-3 B1C and B2a signals were evaluated based on zero baseline measurements from the day of year (DOY) 113 to 116, 2020. Further, the precision and performance of the single point positioning (SPP) and precise point positioning (PPP) are assessed at 9 stations. This assessment manifests that the standard deviations (STDs) of the pseudo-range multipath error are about 0.09 ~ 0.22 m, while STDs of the carrier phase observation noise are about 0.075 mm. For the single-frequency SPP, its positioning precision is about 2.03 ~ 4.85 m and 3.29 ~ 10.73 m at the 99.99% confidence level in horizontal and vertical directions, respectively, while the dual-frequency SPP precision is about 1.92 ~ 8.02 m and 4.81 ~ 12.77 m in horizontal and vertical directions, respectively. For the daily static PPP, the convergence time is about 20 ~ 30 min, while the daily positioning precision can reach 1.38 ~ 4.42 cm and -1.31 ~ 4.34 cm in horizontal and vertical directions, respectively. In general, the quality and the SPP and PPP performance of the BDS-3 B1C&B2a signals are comparable to the GPS and Galileo.     

Beidou wide-area augmentation system clock error correction and performance verification

On December 27, 2018, the Beidou-3 System (BDS-3) has completed the deployment of 18 Medium Earth Orbit (MEO) satellites combined as a space constellation. In addition to the augmentation information for the new system signals B1C and B2a, the BDS-3 is compatible with the three augmentation information broadcast by the BDS-2 system for B1I and B3I signals: equivalent clock error correction, User Differential Ranging Error (UDRE) and Grid Ionosphere Vertical Error (GIVE). In this paper, the observation data of Beidou monitoring network are used to analyze the pseudo-range observation quality of the smooth transition signals B1I and B3I of BDS-2 and BDS-3. At the same time, the relationship between the equivalent clock error correction and the prediction error of the satellite clock is analyzed by using the Two-Way Satellite Time and Frequency Transfer (TWSTFT) data. The results show that the correlation between the equivalent clock error correction and the monitored clock error by using the TWSTFT data is greater than 60%. We calculate the UDRE by using the equivalent clock error correction. The results show that the satellite equivalent clock error correction can improve the accuracy of User Equivalent Range Error (UERE) by about 50%. This paper also compares the positioning accuracy of the BDS-2 satellites with the BDS-2 satellites combined BDS-3 satellites. The results show that the three-dimensional positioning accuracy is improved by about 30% after the BDS-3 satellites are added.     

混合星座导航卫星广播星历相关问题研究

GPS卫星广播星历参数具有参数少、物理意义明确以及精度高等特点,可以考虑将它应用于包含MEO、IGSO和GEO卫星的混合星座卫星导航系统。分析了采用GPs卫星广播星历参数时MEO、IGSO和GEO卫星的广播星历拟合精度,并且比较分析了在一个卫星的轨道周期内,广播星历参数拟合结果的变化规律。仿真结果表明,MEO、IGSO和GEO卫星的广播星历拟合误差最大在分米量级;MEO和IGSO卫星在一个轨道周期内星历参数拟合结果的变化规律相近,但是与GEO卫星的差异较大。     

北斗GEO卫星CEI相时延解算方法研究

连线端站干涉测量(connected element interferometry，CEI)是高精度测角技术，在中高轨卫星、月球及深空航天器定轨定位中有良好的应用前景。基于CEI技术特点，提出了一种新的测量方法，即在相干测距模式下利用测距音和载波信号作为信号源进行连线端站干涉测量。构建了CEI试验系统对北斗GEO卫星进行观测，利用相干测距模式下的下行信号解算群时延、相时延。利用北斗GEO卫星精密星历计算的时延理论值，对北斗GEO卫星CEI群时延和相时延结果进行评估。结果表明，相干测距模式下CEI群时延和相时延残差均值分别为0.47ns、0.08ns，标准差(3σ)分别4.2ns、0.13ns。该项研究验证了相干测距模式下CEI相时延解算的可行性，可为共位地球同步卫星精密相对定位、月球探测器CEI测量提供技术参考。     

Geosynchronous satellites expanding a future GNSS satellite constellation: A precise orbit determination study

The integration of geosynchronous orbit (GSO) satellites in Global Navigation Satellite Systems (GNSS) is mostly discussed to enable a regional enhancement for tracking. But how do GSO satellites affect the orbit determination of the rest of the constellation? How accurately can these orbits be determined in a future GNSS tracking scenario with optical links? In this simulation study we analyze the benefit of GSO satellites as an expansion of a MEO (Medium Earth Orbit) satellite constellation – we selected the Galileo satellite constellation – for MEO Precise Orbit Determination (POD). We address not only the impact on POD of MEO satellites but also the possibility to precisely determine the GSO satellites – geostationary orbits (GEO) and inclined geosynchronous orbits (IGSO) – in such an expanded MEO constellation. In addition to GNSS microwave observations, we analyze the influence of different optical links between the participating entities: Optical two-way Inter-Satellite Links (OISL) and ground-space oriented Optical Two-Way Links (OTWL). These optical measurements together with the GNSS microwave observations give a remarkable benefit for the POD capability. In the case of GNSS and OTWL, we simulate the measurements with regard to a network of 16 ground stations. We pay great attention to the simulation of systematic effects of all measurement techniques. We discuss the influence on the systematic errors as well as the formal orbit uncertainties. A MEO constellation expanded with GSO satellites as well as the use of optical links together with GNSS observations not only improves the MEO satellite orbits but also the GSOs to a great extent.     

Correction model of BDS satellite-induced code bias and its impact on precise point positioning

There are code biases on the pseudo-range observations of the Beidou Navigation Satellite System (BDS) that range in size from several decimeters to larger than one meter. These biases can be divided into two categories, which are the code biases in the pseudo-range observations of Inclined Geo-Synchronous Orbit (IGSO) satellites and Medium Earth Orbit (MEO) satellites and the code biases in the pseudo-range observations of Geosynchronous Earth Orbit (GEO) satellites. In view of the code bias of the IGSO/MEO satellites, the code bias correction model is established using the weighted least square curve fitting method. After the correction, the code biases of the IGSO and MEO satellites are clearly mitigated. A methodology of correcting GEO code bias is proposed based on the empirical mode decomposition (EMD)-wavelet transform (WT) coupled model. The accuracies of the GEO multipath combination of the B1, B2 and B3 frequencies are improved by 39.9%, 17.9%, and 29.4%, respectively. Based on the corrections above, the ten days observations of three Multi-GNSS Experiment (MGEX) stations are processed. The results indicate that the convergence time of the precise point positioning (PPP) can be improved remarkably by applying a code bias. The mean convergence time can be improved by 14.67% after the IGSO/MEO code bias correction. By applying the GEO code bias, the mean convergence time can be further improved by 17.42%.     

Evaluation and analysis on positioning performance of BDS/QZSS satellite navigation systems in Asian-Pacific region

By using the observation data and products of precise obit and clock offset from Multi-GNSS Experiment (MGEX) of the International GNSS Service (IGS) and GNSS Research Centre, Curtin University in this paper, the positioning performance of BDS/QZSS satellite navigation system has been analyzed and evaluated in aspects of the quantity of visible satellites, DOP value, multipath effect, signal-to-noise ratio, static PPP and kinematic PPP. The analysis results show that compared to BDS single system when the cutoff angle are 30°and 40°, the DOP value of BDS/QZSS combined system has decreased above 20%, and the quantity of visible satellites increased about 16–30% respectively, because of the improved spatial geometric configuration. The magnitude of satellite multipath effect of BDS system shows the trend of MEO?>?IGSO?>?GEO, which is consistent with that of QZSS satellite system, as the constellation structure of the two systems is similar. The variation tendencies of signal-to-noise ratio with respect to elevation angle of the two systems are almost the same at all frequencies, showing that at the same elevation angle the signal-to-noise ratio of MEO satellites is higher than that of IGSO satellites, as the higher obit is the lower transmitting power is obtained. For having a specially designed obit, the variation of signal-to-noise ratio of BDS system is more stable. However, the magnitude of signal-to-noise ratio of QZSS system appears the trend of frequency 3?>?frequency 2?>?frequency 1. The static PPP performance of the BDS/QZSS combination system has been improved more significantly than the BDS single system in E, N and U directions. When the cutoff angle are at 7°, 15° and 30°, the PPP accuracy is increased about 25–34% in U direction, 10–13% and 23–34% in E and N directions respectively. When the elevation angle is large (40°), compared to BDS single system at lower elevation angles (7° and 15°) the PPP accuracy of the BDS/QZSS combination system is improved above 30% in U direction. In kinematic PPP performance, compared to BDS single system, the accuracy, availability and reliability of the BDS/QZSS combination system has been improved too, especially at large elevation angles (30° and 40°), the kinematic PPP accuracy in E and U directions has been improved about 10–50%, and above 50% in U direction. It can be concluded that the combination with QZSS system can improve the positioning accuracy, reliability and stability of BDS system. In the future, with the improvement of the satellite construction of Japan’s QZSS system and the global networking of China’s BDS satellites, the QZSS satellites will contribute greatly to improve the positioning accuracy, reliability, availability and stability of GNSS systems in areas such as cities, mountains, densely-packed buildings and severely covered areas in Asian-Pacific region.     

风云三号C星GNOS北斗掩星电离层探测初步结果

利用风云三号卫星C星GNOS掩星探测仪电离层数据,分析了2013年10月FY-3C GNOS探测的北斗掩星电离层廓线分布,将2013年10月1日至2015年10月10日期间FY-3C GNOS观测的F₂层峰值电子密度（N_mF₂）与地面电离层测高仪观测结果进行对比,验证了FY-3C GNOS北斗电离层掩星的探测精度.结果表明,FY3-C GNOS北斗电离层掩星与电离层测高仪探测的N_mF₂数据相关系数为0.96,平均偏差为10.21%,标准差为19.61%.在不同情况下其数据精度有如下特征:白天精度高于夜晚;夏季精度高于分季,分季精度高于冬季;中纬地区精度高于低纬地区,低纬地区精度高于高纬地区; BDS倾斜同步轨道（IGSO）卫星精度高于同步轨道（GEO）卫星和中轨道（MEO）卫星.FY-3C GNOS北斗电离层掩星与国际上其他掩星电离层数据精度的一致性对GNSS掩星探测资料的综合利用具有重大意义.      

Analysis on navigation accuracy of high orbit spacecraft based on BDS GEO and IGSO satellites

To make up for the insufficiency of earth-based TT&C systems, the use of GNSS technology for high-orbit spacecraft navigation and orbit determination has become a new technology. It is of great value to applying Geosynchronous Earth Orbit (GEO) and Inclined GeoStationary Orbit (IGSO) navigation satellites for supporting the navigation of high-orbit spacecraft since there are three different types of navigation satellites in BeiDou Navigation Satellite System (BDS): Medium Earth Orbit (MEO), GEO and IGSO. This paper conducts simulation experiments based on Two-Line Orbital Element (TLE) data to analyze and demonstrate the role of these satellites in the navigation of high-orbit spacecraft. Firstly, the spacecraft in GEO was used as the target satellite to conduct navigation experiments. Experiments show that for the spacecraft on the GEO orbit, after adding GEO and IGSO respectively on the basis of receiving MEO navigation satellite signals, the accuracies were improved by 7.22 % and 6.06 % respectively. When adding both GEO and IGSO navigation satellites at the same time, the accuracy can reach 16 m. In the second place, navigation and positioning experiments were carried out on three high elliptical orbit (HEO) satellites with different semimajor axis (32037.2 km, 42385.9 km, 67509.6 km). The experiments show that the number of visible satellites has been improved significantly after adding GEO and IGSO navigation satellites at the same time. The visible satellites in these three orbits were improved by 32.84 %, 41.12 % and 37.68 %, respectively compared with only observing MEO satellites.The RMS values of the navigation positioning errors of these three orbits are 25.59 m, 87.58 m and 712.48 m, respectively.     

新一代卫星导航信号测量性能分析

导航信号的测量性能最终影响系统定位、测速、授时等服务精度, 是系统顶层设计的重要论证内容之一. 结合COMPASS系统新一代卫星导航信号体制框架设计, 分析了各种应用条件下的伪距、载波相位和多普勒测量精度, 并以典型设计参数为例进行了数值计算. 结果表明, 在接收机典型设计参数和工作条件下, 各信号分量均能够实现0.1m的伪距测量精度、0.006周的载波相位测量精度以及0.005m·s-1的多普勒测量精度. 首次给出的针对新信号体制各项测量性能的研究结果可为卫星导航系统信号体制设计、 导航接收机关键参数设计以及卫星导航系统用户测距误差预算等顶层设计提供参考.      

Design and performances of laser retro-reflector arrays for Beidou navigation satellites and SLR observations

Beidou is the regional satellite navigation system in China, consisting of three kinds of orbiting satellites, MEO, GEO and IGSO, with the orbital altitudes of 21500–36000 km. For improving the accuracy of satellites orbit determination, calibrating microwave measuring techniques and providing better navigation service, all Beidou satellites are equipped with laser retro-reflector arrays (LRAs) to implement high precision laser ranging. The paper presents the design of LRAs for Beidou navigation satellites and the method of inclined installation of LRAs for GEO satellites to increase the effective reflective areas for the regional ground stations. By using the SLR system, the observations for Beidou satellites demonstrated a precision of centimeters. The performances of these LRAs on Beidou satellites are very excellent.     

Compatibility of Terrestrial Reference Frames used in GNSS broadcast messages during an 8 week period of 2019

The operational Terrestrial Reference Frames (TRFs) realized through the evaluation of broadcast ephemerides for GPS, GLONASS, Galileo, BeiDou-2 and BeiDou-3 have been compared to IGS14, the TRF realized by the International GNSS Service (IGS). The TRFs realized by the GPS, GLONASS, Galileo, and BeiDou-2 and BeiDou-3 broadcast ephemerides are the orbital realizations of WGS 84 (G1762′), PZ90.11, GTRF19v01, and BDCS respectively. These TRFs are compared using up to 56 days of data (21 July-14 Sept 2019) at a 5 or 15-min rate. The operational TRFs are compared to IGS14 in a 7-parameter similarity (Helmert) transformation. Numerical results show that the operational GNSS TRFs differ from IGS14 at a level no greater than 4 cm for Galileo, 6 cm for GPS and BeiDou-3, 13 cm for GLONASS, and 48 cm for a limited set of BeiDou-2 Medium Earth Orbit (MEO) vehicles.     

基于地面基站的定位系统构建和方案

针对大型、复杂、多功能建筑,其内部信号环境恶劣,卫星导航的信号衰减较大,较难稳定捕获跟踪,建筑内多径效应严重,短多径对定位精度的影响较大,直接使用卫星导航信号进行定位难度大的问题,提出了一种基于地面基站的大区域（建筑群）室内定位方案。根据频率与信号穿透性能和空间衰减之间的关系,选择甚高频频段作为信号载波,采用码伪距和载波伪距联合定位的方式,可同时兼顾覆盖性和定位性能。利用所提出的新型定位方式,搭建了一个基本测试系统,通过信号的产生、发射、无线传播,进行了信号的捕获、跟踪和伪距求差解算,初步验证了本文方法的可行性及覆盖能力。      

The use of ionospheric tomography and elevation masks to reduce the overall error in single-frequency GPS timing applications

Signals from Global Positioning System (GPS) satellites at the horizon or at low elevations are often excluded from a GPS solution because they experience considerable ionospheric delays and multipath effects. Their exclusion can degrade the overall satellite geometry for the calculations, resulting in greater errors; an effect known as the Dilution of Precision (DOP). In contrast, signals from high elevation satellites experience less ionospheric delays and multipath effects. The aim is to find a balance in the choice of elevation mask, to reduce the propagation delays and multipath whilst maintaining good satellite geometry, and to use tomography to correct for the ionosphere and thus improve single-frequency GPS timing accuracy. GPS data, collected from a global network of dual-frequency GPS receivers, have been used to produce four GPS timing solutions, each with a different ionospheric compensation technique. One solution uses a 4D tomographic algorithm, Multi-Instrument Data Analysis System (MIDAS), to compensate for the ionospheric delay. Maps of ionospheric electron density are produced and used to correct the single-frequency pseudorange observations. This method is compared to a dual-frequency solution and two other single-frequency solutions: one does not include any ionospheric compensation and the other uses the broadcast Klobuchar model. Data from the solar maximum year 2002 and October 2003 have been investigated to display results when the ionospheric delays are large and variable. The study focuses on Europe and results are produced for the chosen test site, VILL (Villafranca, Spain). The effects of excluding all of the GPS satellites below various elevation masks, ranging from 5° to 40°, on timing solutions for fixed (static) and mobile (moving) situations are presented. The greatest timing accuracies when using the fixed GPS receiver technique are obtained by using a 40° mask, rather than a 5° mask. The mobile GPS timing solutions are most accurate when satellites at lower elevations continue to be included: using a mask between 10° and 20°. MIDAS offers the most accurate and least variable single-frequency timing solution and accuracies to within 10 ns are achieved for fixed GPS receiver situations. Future improvements are anticipated by combining both GPS and Galileo data towards computing a timing solution.     

Time synchronization of new-generation BDS satellites using inter-satellite link measurements

Autonomous satellite navigation is based on the ability of a Global Navigation Satellite System (GNSS), such as Beidou, to estimate orbits and clock parameters onboard satellites using Inter-Satellite Link (ISL) measurements instead of tracking data from a ground monitoring network. This paper focuses on the time synchronization of new-generation Beidou Navigation Satellite System (BDS) satellites equipped with an ISL payload. Two modes of Ka-band ISL measurements, Time Division Multiple Access (TDMA) mode and the continuous link mode, were used onboard these BDS satellites. Using a mathematical formulation for each measurement mode along with a derivation of the satellite clock offsets, geometric ranges from the dual one-way measurements were introduced. Then, pseudoranges and clock offsets were evaluated for the new-generation BDS satellites. The evaluation shows that the ranging accuracies of TDMA ISL and the continuous link are approximately 4?cm and 1?cm (root mean square, RMS), respectively. Both lead to ISL clock offset residuals of less than 0.3?ns (RMS). For further validation, time synchronization between these satellites to a ground control station keeping the systematic time in BDT was conducted using L-band Two-way Satellite Time Frequency Transfer (TWSTFT). System errors in the ISL measurements were calibrated by comparing the derived clock offsets with the TWSTFT. The standard deviations of the estimated ISL system errors are less than 0.3?ns, and the calibrated ISL clock parameters are consistent with that of the L-band TWSTFT. For the regional BDS network, the addition of ISL measurements for medium orbit (MEO) BDS satellites increased the clock tracking coverage by more than 40% for each orbital revolution. As a result, the clock predicting error for the satellite M1S was improved from 3.59 to 0.86?ns (RMS), and the predicting error of the satellite M2S was improved from 1.94 to 0.57?ns (RMS), which is a significant improvement by a factor of 3–4.     

Analysis of BDS-3 distributed autonomous navigation based on BeiDou system simulation platform

Satellite autonomous navigation is an important function of the BeiDou-3 navigation System (BDS-3). Satellite autonomous navigation means that the navigation satellite uses long-term forecast ephemeris and Inter-Satellite Link (ISL) measurements to determinate its own spatial position and time reference without the support of the ground Operation and Control System (OCS) for a long time to ensure that the navigation system can normally maintain the time and space reference. This paper aims to analyze the feasibility of distributed autonomous navigation algorithms. For the first time, a ground parallel autonomous navigation test system (GPANTS) is built. The performance of distributed autonomous navigation is then analyzed using the two-way ISL ranging of BDS-3 satellites. First, the BDS simulation platform and the GPANTS are introduced. Then, the basic principles of distributed satellite autonomous orbit determination and time synchronization based on ISL measurements are summarized. Preliminary evaluation of the performance of the BDS-3 constellation autonomous navigation service under ideal conditions through simulation data. Then the performance of autonomous navigation for 22 BeiDou-3 satellites using ISL measurements is evaluated. The results show that when satellites operate autonomously for 50 days without the support of any ground station, the User Range Error (URE) of autonomous orbit determination is better than 3 m, and the time synchronization accuracy is better than 4 ns.     

北斗卫星导航系统实时定轨与钟差处理策略

目前鲜有对北斗卫星导航系统（BeiDouNavigationSatelliteSystem,BDS）实时精密定轨与钟差确定的研究,文章提出了BDS实时轨道与实时钟差处理策略,包括了观测与动力学模型、实时轨道与实时钟差处理流程与评估方法。尤其对于实时钟差,为了提高计算效率,联合使用两个独立并行的线程估计非差绝对钟差和历元间相对钟差。利用多模全球卫星导航系统试验(MGEX)与全球连续检测评估系统（iGMAS）实测数据进行了北斗实时轨道与钟差解算,BDS实时轨道径向平均精度对于GEO卫星优于20cm,对于IGSO与MEO一般优于10cm;钟差精度对于GEO卫星为0.5~4.5ns,对于IGSO／MEO为0.2~2.0ns。基于目前的轨道与钟差结果,实时精密单点定位（PrecisePointPositioning,PPP）结果可以达到分米量级。     

北斗首颗备份卫星性能初步分析

主要从卫星钟差预报、轨道测定精度、伪距波动情况等角度分析了I6卫星与北斗卫星导航系统（BDS）其他现役倾斜地球同步轨道（IGSO）卫星的异同,并从位置精度因子（PDOP）和格网可用性评估了I6卫星入网对BDS的贡献。利用星地双向时频传递设备观测的星地钟差数据,评估了I6卫星星载原子钟的预报性能,结果表明,I6卫星发播的卫星钟参数外推5h预报误差的均方根误差（RMS）为232ns,外推1h预报误差的RMS为073ns,与现役IGSO卫星钟差预报水平相当;对多星联合精密定轨结果分析表明,与北斗现役I3卫星相比,姿态控制方式优化后的I6卫星在地影期间的轨道精度并未发生明显衰减,克服了现有北斗二号卫星在地影期间轨道精度下降,从而影响北斗服务的连续性、可用性问题;利用大口径抛物面天线采集到的数据对I6卫星的伪距波动进行了分析,结果表明I6卫星单个观测弧段内其伪距波动峰峰差约为1m,与其他IGSO卫星一致;进行PDOP仿真计算,结果表明I6卫星的加入使得喀什地区的PDOP最大值由1282下降为726,PDOP大于6的时段所占百分比由2911%下降为1721%;对格网电离层产品实施解算,结果表明I6卫星的加入使得6个电离层格网点的可用度提升至95%以上。