北斗实时精密轨道和钟差产品解算策略及精度评定

随着北斗卫星导航系统全球星座部署即将完成，其应用领域不断扩大，实时精密服务性能受到了极大关注。基于动力学精密定轨方法，设计了北斗卫星实时轨道、钟差算法流程和解算策略。利用不同频点信号，分别计算了BDS-2和BDS-3卫星的实时精密轨道和钟差，建立了完整的轨道和钟差精度评定方法，重点对解算的实时产品的精度进行了评定。结果表明：BDS-2和BDS-3实时精密轨道和钟差产品精度均可满足大部分实时用户的需求。对于B1IB3I频点，BDS-3 MEO卫星的实时轨道精度约为26cm，径向精度约为6cm，实时钟差精度约为0.45ns，且相较于BDS-2，性能更加稳定；对于B1CB2a频点，BDS-3 MEO卫星的实时轨道精度优于20cm，精度和稳定性较高。     

新一代北斗试验卫星伪距质量初步评估

为验证北斗全球系统卫星新型导航信号体制、星间链路和高精度原子钟等关键技术,中国于2015年3月30日至2016年2月1日间发射了5颗新一代北斗试验卫星。试验卫星除了播发新的民用信号B1C和B2外,同时还播发B1I和B3I平稳过渡信号。试验卫星导航信号的伪距质量以及北斗现有工作卫星存在的与高度角相关伪距误差问题在新一代北斗卫星上是否得到解决是大家普遍关注的问题,将基于北斗试验卫星实测数据对此进行初步评估与验证。     

HOI延迟对LEO卫星简化动力学POD的影响

通常使用无电离层(IF)线性组合(LC)消除低地球轨道(LEO)卫星简化动力学精密定轨(POD)一阶电离层延迟误差,忽略了高阶电离层(HOI)延迟误差。随着LEO卫星POD技术的发展,计算不同轨道高度的HOI延迟并探索其变化已成为进一步提高POD精度的重要手段。首先,使用国际参考电离层-2016(IRI-2016)和国际地磁参考场第13代(IGRF-13)模型,计算电离层穿刺点(IPP)位置和地磁场强度。其次,使用平滑星载GNSS数据计算电离层斜路径总电子含量(STEC)。然后,分别计算GOCE、GRACE-A和SWARM-A/B卫星的二阶和三阶电离层延迟。最后,评估了HOI延迟对LEO卫星重叠轨道分析、卫星激光测距(SLR)检核和精密科学轨道(PSO)比较结果的影响。实验结果表明：HOI延迟对LEO卫星简化动力学POD的影响大约在毫米至厘米的数量级上;HOI延迟对LEO卫星简化动力学POD外符合精度的影响分别达到0.92,0.22,0.21和0.18 mm;随着LEO卫星轨道高度的增加,HOI延迟对LEO卫星简化动力学POD的影响减小。     

Aiming at a 1-cm Orbit for Low Earth Orbiters: Reduced-Dynamic and Kinematic Precise Orbit Determination

The computation of high-accuracy orbits is a prerequisite for the success of Low Earth Orbiter (LEO) missions such as CHAMP, GRACE and GOCE. The mission objectives of these satellites cannot be reached without computing orbits with an accuracy at the few cm level. Such a level of accuracy might be achieved with the techniques of reduced-dynamic and kinematic precise orbit determination (POD) assuming continuous Satellite-to-Satellite Tracking (SST) by the Global Positioning System (GPS). Both techniques have reached a high level of maturity and have been successfully applied to missions in the past, for example to TOPEX/POSEIDON (T/P), leading to (sub-)decimeter orbit accuracy. New LEO gravity missions are (to be) equipped with advanced GPS receivers promising to provide very high quality SST observations thereby opening the possibility for computing cm-level accuracy orbits. The computation of orbits at this accuracy level does not only require high-quality GPS receivers, but also advanced and demanding observation preprocessing and correction algorithms. Moreover, sophisticated parameter estimation schemes need to be adapted and extended to allow the computation of such orbits. Finally, reliable methods need to be employed for assessing the orbit quality and providing feedback to the different processing steps in the orbit computation process. This revised version was published online in August 2006 with corrections to the Cover Date.     

双线程滑动窗口多系统GNSS超快精密定轨实现及评估

全球导航卫星系统（GNSS）超快精密定轨为GNSS实时应用提供了高精度空间基准。基于天地协同定位、导航与授时（PNT）网络服务中心实现了四系统GNSS卫星超快精密定轨,并对定轨结果进行精度评价。介绍了天地协同PNT网络的概念内涵以及网络服务中心部署的超快精密定轨软件架构和详细功能,并针对实时应用需求提出了一种双线程滑动窗口超快精密定轨策略。最后利用重叠弧段比较、与外部轨道产品比较以及卫星激光测距（SLR）检核3种方式对定轨结果进行了精度评价。结果表明,与武汉大学分析中心的最终事后精密轨道产品相比,四系统GNSS MEO卫星预报6 h弧段的径向均方根（RMS）误差整体在2~5 cm水平,BDS2 IGSO卫星最小一维RMS误差在10~15 cm水平;GPS和Galileo卫星的SLR检核残差均值在1~3 cm水平,标准差在3~6 cm水平,能够满足后续厘米级实时应用对空间基准的精度需求。     

Basic performance of BeiDou-2 navigation satellite system used in LEO satellites precise orbit determination

The visibility for low earth orbit（LEO） satellites provided by the BeiDou-2 system is analyzed and compared with the global positioning system（GPS）. In addition, the spaceborne receivers＇ observations are simulated by the BeiDou satellites broadcast ephemeris and LEO satellites orbits. The precise orbit determination（POD） results show that the along-track component accuracy is much better over the service area than the non-service area, while the accuracy of the other two directions keeps at the same level over different areas. However, the 3-dimensional（3D） accuracy over the two areas shows almost no difference. Only taking into consideration the observation noise and navigation satellite ephemeris errors, the 3D accuracy of the POD is about30 cm. As for the precise relative orbit determination（PROD）, the 3D accuracy is much better over the eastern hemisphere than that of the western hemisphere. The baseline length accuracy is 3.4 mm over the service area, and it is still better than 1 cm over the non-service area. This paper demonstrates that the BeiDou regional constellation could provide global service to LEO satellites for the POD and the PROD. Finally, the benefit of geostationary earth orbit（GEO） satellites is illustrated for POD.     

北斗空间信号误差统计特征及描述方法研究

通过对比北斗卫星导航系统(BeiDou Navigation Satellite System,BDS)广播星历与事后精密星历,提取了轨道和卫星时钟误差。基于北斗轨道误差及北斗卫星时钟误差统计特征分析,构建区别于全球定位系统(Global Positioning System,GPS)的BDS空间信号用户测距误差(Signal-In-Space User Range Error,SISRE)描述方法,对BDS广播星历中用户测距精度(User Range Accuracy,URA)进行了验证。6个月的北斗数据测试结果表明,北斗GEO、IGSO和MEO卫星的URA分别为3.0m、1.9m和1.6m。     

A demonstration of sub meter GPS orbit determination and highprecision user positioning

High-accuracy orbits have been determined for satellites of the Global Positioning System (GPS), with submeter orbit accuracy demonstrated for two well-tracked satellites. Baselines of up to 2000 km in North America determined with the GPS orbits shows daily repeatability of 0.3-2 parts in 10⁸ and agree with very long baseline interferometry (VLBI) solutions at the level of 1.5 parts in 10 ⁸. Tests used to assess orbit accuracy include orbit repeatability from independent data sets, orbit prediction, ground baseline determination, and formal errors. One satellite tracked for eight hours each day shows RMS errors below 1 m even when predicted more than three days outside of a 1-week data arc. These results demonstrate the powerful relative positioning capability available from differential GPS tracking. Baselines have also been estimated between Florida and sites in the Caribbean region over 1000 km away, with daily repeatability of 1-4 parts in 10⁸. The best orbit estimation strategies included data arcs of 1-2 weeks, process noise models for tropospheric fluctuations, combined processing of GPS carrier phase and pseudorange data, and estimation of GPS solar pressure coefficients     

Spaceborne GPS receiver antenna phase center offset and variation estimation for the Shiyan 3 satellite

In determining the orbits of low Earth orbit (LEO) satellites using spaceborne GPS, the errors caused by receiver antenna phase center offset (PCO) and phase center variations (PCVs) are gradually becoming a major limiting factor for continued improvements to accuracy. Shiyan 3, a small satellite mission for space technology experimentation and climate exploration, was developed by China and launched on November 5, 2008. The dual-frequency GPS receiver payload delivers 1 Hz data and provides the basis for precise orbit determination within the range of a few centime-ters. The antenna PCO and PCV error characteristics and the principles influencing orbit determi-nation are analyzed. The feasibility of PCO and PCV estimation and compensation in different directions is demonstrated through simulation and in-flight tests. The values of receiver antenna PCO and PCVs for Gravity Recovery and Climate Experiment (GRACE) and Shiyan 3 satellites are estimated from one month of data. A large and stable antenna PCO error, reaching up to 10.34 cm in the z-direction, is found with the Shiyan 3 satellite. The PCVs on the Shiyan 3 satellite are estimated and reach up to 3.0 cm, which is slightly larger than that of GRACE satellites. Orbit validation clearly improved with independent k-band ranging (KBR) and satellite laser ranging (SLR) measurements. For GRACE satellites, the average root mean square (RMS) of KBR resid-uals improved from 1.01 cm to 0.88 cm. For the Shiyan 3 satellite, the average RMS of SLR resid-uals improved from 4.95 cm to 4.06 cm.     

多机构比对融合的分布式InSAR编队星间基线确定

星间基线高精度确定是分布式干涉合成孔径雷达（InSAR）系统完成科学任务的重要保证,受星载全球定位系统（GPS）接收机连续跟踪弧段短、个别弧段共视GPS卫星个数少或模糊度固定成功率低、频繁轨道机动等因素影响,分布式InSAR高精度基线确定仍有不可靠的风险。通过多机构产品互比来识别基线精度较差的时间段,降低不可靠风险,并通过多机构产品融合进一步提高基线精度。选用重力反演与气候实验（GRACE）卫星数据进行实验,国防科技大学（NDT）和西安测绘研究所（CHS）采用不同的基线处理软件和简化动力学策略,保证了各自的基线产品具有一定的独立性。实验表明,多机构互比对可以有效识别基线精度较差的时间段,NDT和CHS的基线产品之间具有很好的一致性,互比对残差的均方根（RMS）在R、T、N方向分别为0.7、0.9、0.7 mm,二者之间没发现明显系统偏差,大约97.86%的基线三维互比对残差量级在2 mm以内。两个机构基线产品融合后发现可进一步降低基线产品中的随机波动误差,K/Ka波段测距（KBR）系统校核结果表明融合基线产品精度较NDT基线产品提高8.97%,较CHS基线产品提高29.21%。     

低成本U-blox模块的单频GPS/BDS增强PPP定位性能分析

以U-blox单频接收机采集数据,在GPS与GPS/BDS两种解算模式下进行局域增强精密单点定位(PPP)解算,并进行模糊度固定,对其在不同环境下的定位性能进行实验研究和分析。实验结果表明:在静态环境下,GPS/BDS浮点解收敛至cm级需3min左右,较GPS缩短64%,GPS/BDS定位精度RMS在平面与高程方向分别为(3.2cm,2.7cm),较GPS提升(47%,59%);GPS/BDS在30s左右可固定模糊度,固定后定位精度为(0.4cm,1.0cm),较GPS/BDS浮点解提升(88%,63%)。在动态环境下,GPS/BDS浮点解收敛至cm级需4min左右,较GPS提升59%,定位精度为(3.1cm,5.9cm),较GPS提升(34%,43%);GPS/BDS获得固定解需2min左右,固定后定位精度为(0.7cm,1.0cm),较GPS/BDS浮点解提升(77%,83%)。     

I: PRECISE ORBIT DETERMINATION AND GRAVITY FIELD MODELLING: Strategies for Precise Orbit Determination of Low Earth Orbiters Using the GPS

Considerable experience accumulated during the past decade in strategies for processing GPS data from ground-based geodetic receivers. First experience on the use of GPS observations from spaceborne receivers for orbit determination of satellites on low altitude orbits was gained with the launch of TOPEX/POSEIDON ten years ago. The launch of the CHAMP satellite in July 2000 stimulated a number of activities worldwide on improving the strategies and algorithms for orbit determination for Low Earth Orbiters (LEOs) using the GPS. Similar strategies as for ground-based receivers are applied to data from spaceborne GPS receivers to determine high precision orbits. Zero- and double-differencing techniques are applied to obtain kinematic and/or reduced-dynamic orbits with an accuracy which is today at the decimeter level. Further developments in modeling and processing strategies will continuously improve the quality of GPS-derived LEO orbits in the near future. A significant improvement can be expected from fixing double-difference phase ambiguities to integer numbers. Particular studies focus on the impact of a combined processing of LEO and GPS orbits on the quality of orbits and the reference frame realization. This revised version was published online in August 2006 with corrections to the Cover Date.     

北斗/GPS双频载波相位单点定位模型及精度分析

针对海洋工程实时米级绝对定位需求,利用双频伪距、载波相位观测量和同时估计接收机位置、接收机钟差和载波相位模糊度,构建了一种双频载波相位实时单点定位方法.亚太区域14个测站试验结果显示:北斗水平和高程定位RMS分别为1.33m和1.81m,GPS为0.60m和0.85m,北斗/GPS组合为0.56m和0.72m;船载动态试验结果显示:北斗水平和高程定位RMS分别为1.40m 和2.46m,GPS为0.69m 和0.90m,北斗/GPS组合为0.65m和0.83m.     

双频双星座地基增强系统精度和完好性算法

针对单频单星座地基增强系统（GBAS）无法满足飞机III类精密进近与着陆导航性能需求的问题，提出了将北斗导航卫星系统（BDS）与全球定位系统（GPS）进行融合，构建一种新型的基于GPS/BDS的双频双星座GBAS。首先，分析了GBAS的工作原理，并对Hatch滤波器的误差进行了分析，给出了一种适用于双频GBAS的无码载偏离载波相位平滑伪距算法；然后，对机载完好性算法进行了研究，给出了H0和H1假设下的机载保护级计算方法；最后，进行了系统验证实验，实验结果表明，单星座GBAS不能满足飞机III类精密进近与着陆导航的性能需求，GPS和BDS融合后可见卫星个数得到提升，优化了卫星几何分布，进而使得系统的可用性由80.6081%提升到大于99.9999%。     

载波相位平滑伪距在GPS/SINS紧组合导航系统中的应用

针对GPS/SINS紧组合导航系统中伪距噪声大从而引起组合导航系统精度低的问题,提出了将载波相位平滑伪距方法引入到组合导航系统中,利用具有较高精度的载波相位对低精度伪距进行平滑滤波,在建立观测方程的同时,为了减小Kalman滤波器计算量,选用最佳4颗卫星的伪距与伪距率作为观测值,并提出了一种四面体选星法,该方法不需要进行矩阵求逆运算,减小了运算量。利用光纤陀螺捷联惯导系统与GPS接收机搭建了实验验证系统,通过车载实验对所提出的方法进行了验证,实验结果表明,经过载波相位平滑后的伪距噪声得到了降低,从而能够进一步提高GPS/SINS组合导航系统的定位精度,其位置误差均方根值相比无载波相位平滑减小近40%。     

广播星历旋转误差对低轨星载BDS-3/GPS实时精密定轨影响分析

基于LT-01A卫星星载BDS-3/GPS观测值进行了星载实时精密定轨研究,并重点分析了广播星历旋转误差对实时定轨精度的影响。通过赫尔默特转换评估了所选时段内GPS和BDS-3广播星历轨道旋转误差,显示BDS-3广播星历旋转误差可达-8.7 mas,平均量级较GPS大约2.5倍。BDS-3广播星历经旋转改正后,轨道切向、法向均方根(RMS)误差从25 cm左右提升至10 cm量级,提升幅度超过50%。因此,基于星载BDS-3以及BDS-3/GPS联合的实时定轨精度受BDS-3星历旋转误差影响严重,且主要作用于切向和法向。经过旋转改正后,单独BDS-3实时定轨在切向、法向、径向RMS分别为21.0 cm、10.7 cm及11.2 cm,其切向和法向精度比改正前分别提升15.0%和31.8%;BDS-3与GPS联合定轨进一步提升切向精度至19.4 cm。得益于BDS-3广播星历较高的精度,单BDS-3以及BDS-3/GPS联合的实时定轨在旋转改正前的三维RMS分别为31.9 cm和29.2 cm,较单GPS实时定轨分别提升9.1%和16.8%;添加旋转改正后,其定轨精度分别提升至26.7 ...     

Integrating BDS and GPS for precise relative orbit determination of LEO formation flying

Low-Earth-Orbit(LEO) formation-flying satellites have been widely applied in many kinds of space geodesy. Precise Relative Orbit Determination(PROD) is an essential prerequisite for the LEO formation-flying satellites to complete their mission in space. The contribution of the BeiDou Navigation Satellite System(BDS) to the accuracy and reliability of PROD of LEO formation-flying satellites based on a Global Positioning System(GPS) is studied using a simulation method. Firstly, when BDS is added to GPS, the mean number of visible satellites increases from9.71 to 21.58. Secondly, the results show that the 3-Dimensional(3 D) accuracy of PROD, based on BDS-only, GPS-only and BDS + GPS, is 0.74 mm, 0.66 mm and 0.52 mm, respectively. When BDS co-works with GPS, the accuracy increases by 29.73%. Geostationary-Earth-Orbit(GEO) satellites and Inclined Geosynchronous-Orbit(IGSO) satellites are only distributed over the Asia-Pacific region; however, they could provide a global improvement to PROD. The difference in PROD results between the Asia-Pacific region and the non-Asia-Pacific region is not apparent. Furthermore, the value of the Ambiguity Dilution Of Precision(ADOP), based on BDS + GPS, decreases by 7.50% and 8.26%, respectively, compared with BDS-only and GPS-only. Finally, if the relative position between satellites is only a few kilometres, the effect of ephemeris errors on PROD could be ignored. However, for a several-hundred-kilometre separation of the LEO satellites, the SingleDifference(SD) ephemeris errors of GEO satellites would be on the order of centimetres. The experimental results show that when IGSO satellites and Medium-Earth-Orbit(MEO) satellites co-work with GEO satellites, the accuracy decreases by 17.02%.     

Inter-satellite link augmented BeiDou-3 orbit determination for precise point positioning

Precise Point Positioning(PPP) requires precise products, including high-accuracy satellite orbit and clock parameters. It is impossible to obtain an orbit solution that is sufficiently accurate for PPP services with a regional tracking network; therefore, satellite orbits are usually estimated by a global tracking network with a large number of ground stations. However, it is expensive to build globally distributed stations. Fortunately, BeiDou-3 satellites carry an InterSatellite Link(ISL) pay...     

Spacecraft orbit determination using GPS navigation solutions

The orbit determination using the GPS navigation solutions for the KOMPSAT-1 spacecraft has been studied. The Cowell method of special perturbation theories was employed to develop a precision orbit propagation, and the perturbations due to geopotential, the gravity of the Sun and the Moon, solid Earth tides, ocean tides, the Earth's dynamic polar motion, solar radiation pressure, and atmospheric drag were modeled. Specifically, the satellite box-wing macro model was applied to minimize the drag errors at low altitude. The estimation scheme consisted of an extended Kalman filter and Bayesian least square method. To investigate the applicability of the method to the KOMPSAT-1 spacecraft, the orbit determination was accomplished using the GPS navigation solutions for the TOPEX/POSEIDON and TAOS satellites. The orbit determination results were compared with NASA POE generated by global laser tracking. The position and velocity accuracy was estimated about 16∼7 m and 0.0157∼0.0074 m·s⁻¹ RMS, respectively, for the two satellites in the presence of SA. These results verify that an orbit determination scheme using GPS navigation solutions can provide the static orbit information and reduce conspicuously the position and velocity errors of navigation solutions. It can be suggested that the sequential and batch orbit determination using the GPS navigation solutions be the most appropriate method in the KOMPSAT-1 type mission.     

中低纬地区混合LEO星座增强GNSS UPPP收敛性能评估

针对全球卫星导航系统（GNSS）精密单点定位（PPP）收敛时间过长的问题，提出了利用低轨卫星（LEO）几何结构变化快的优势，增强GNSS非差非组合PPP（UPPP）的收敛性能。选取中低纬度地区28个能接收GPS、GALILEO和BDS3信号的测站观测数据，比较了极轨和混合LEO星座的增强效果。结果表明：混合LEO星座增强GPS、GALILEO和BDS组合系统时，各测站收敛时间减少60%~80%，70%的测站收敛速度优于极轨星座。当混合LEO星座增强单BDS时，CL和GCL组合系统的收敛时间相当，ENU方向定位误差变化基本一致。收敛时间从10~20 min 下降至3 min以内，原因是混合LEO增强BDS定位时，大大改善了卫星的空间结构。