Virtual target guidance-based distributed model predictive control for formation control of multiple UAVs

The paper proposes a Virtual Target Guidance (VTG)-based distributed Model Predictive Control (MPC) scheme for formation control of multiple Unmanned Aerial Vehicles (UAVs). First, a framework of distributed MPC scheme is designed in which each UAV only shares the information with its neighbors, and the obtained local Finite-Horizon Optimal Control Problem (FHOCP) can be solved by swarm intelligent optimization algorithm. Then, a VTG approach is developed and integrated into the distributed MPC scheme to achieve trajectory tracking and obstacle avoidance. Further, an event-triggered mechanism is proposed to reduce the computational burden for UAV formation control, which takes into consideration the predictive state errors as well as the convergence of cost function. Numerical simulations show that the proposed VTG-based distributed MPC scheme is more computationally efficient to achieve formation control of multiple UAVs in comparison with the traditional distributed MPC method.     

基于直接配点法的绳系卫星系统变轨控制

讨论了不必回收子星的二体绳系卫星系统(TSS)的变轨方案。假设TSS质心运动满足经典的二脉冲Hohmann变轨,用未变形绳长加速率控制两次脉冲期间的TSS运动。利用直接配点法中的Hermite-Simpson方法将控制消耗最小的最优问题离散为大型非线性规划问题,然后用MATLAB的SNOPT软件包求解;针对初始偏差较大的实际情况,又结合直接配点法和滚动时域控制得到了解析的反馈控制律。仿真算例表明,得到的TSS变轨过程状态变化平滑,控制消耗较小,而且变轨之后TSS接近平衡状态;此外,反馈控制律对最优路径的跟踪效果较好,能够消除初始偏差的影响。     

Three-dimensional midcourse guidance using neural networks forinterception of ballistic targets

A suboptimal midcourse guidance law is obtained for interception of free-fall targets in the three-dimensional (3D) space. Neural networks are used to approximate the optimal feedback strategy suitable for real-time implementation. The fact that the optimal trajectory in the 3D space does not deviate much from a vertical plane justifies the use of the two-dimensional (2D) neural network method previously studied. To regulate the lateral errors in the missile motion produced by the prediction error of the intercept point, the method of feedback linearization is employed. Computer simulations confirm the superiority of the proposed scheme over linear quadratic regulator guidance and proportional navigation guidance as well as its approximating capability of the optimal trajectory in the 3D space     

不确定性非线性系统的自适应输出反馈控制

研究了一种不确定性非线性系统的自适应输出反馈控制方法.首先引入伪控制信号使系统反馈线性化,然后设计一个线性动态补偿器和在线神经网络,自适应消除不确定性和建模所引起的误差.仿真结果表明,该控制方法能够消除系统的稳态误差,提高系统动态性能,并且具有较好的鲁棒性.     

面向悬浮光力系统的集成化反馈控制器研究

悬浮光力系统具有高灵敏度、高稳定性和低耗散等特点,有望发展成为新型高性能力学传感器。针对目前悬浮光力系统存在的反馈控制器兼容性差、软硬件成本高、集成度低等问题,提出了一种兼容多种反馈控制模式的软硬件设计方案,并研制了一套高度集成的反馈控制器,在160 mm×170 mm×42 mm的尺寸上集成了六通道模数/数模转换器、滤波器、现场可编程门阵列+微处理器(FPGA+ARM)等功能模块,并且开发了基于数字锁相环和比例积分微分(PID)控制器的控制算法,最终在同一套硬件系统上实现了跨尺度微粒的运动信息采集和反馈控制,以及数十赫兹至亚兆赫兹的感知带宽。实验结果表明,该集成反馈控制器能够实现超高真空(10^-6 Pa量级)下亚微米及微米尺度微粒的稳定悬浮和运动控制。在扩展系统感知带宽的同时减小了整体体积,为悬浮光力传感技术的器件化奠定了基础。     

谐振式光子晶体光纤陀螺信号检测及处理技术研究

谐振式光子晶体光纤陀螺是一种具有小型化、高精度等潜在技术优势的新型光纤陀螺,是国内外惯性器件研究的一个重要发展方向。针对谐振式光子晶体光纤陀螺的结构和信号检测原理进行了详细的叙述,确定了基于FPGA的陀螺信号检测总体方案,陀螺信号处理及控制模块主要由频差信号解调、复合拍频检测、闭环反馈控制、数据编码输出以及调制信号模块组成;随后重点介绍了窄线宽半导体激光器的驱动控制方案,在调制解调及频率偏差检测方案上采用数字相敏检波器实现频率偏差检测,在谐振频率闭环跟踪锁定方案上采用数字PI控制器实现环路光频率控制;最后进行了谐振式光子晶体光纤陀螺实验测试系统搭建,以及谐振曲线测试和谐振频率闭环锁定测试。     

新一代歼击机超机动飞行的动态逆控制

 根据反馈线性化理论, 讨论了神经网络自适应非线性动态逆控制设计。首先根据时标分离原则, 采用动态逆方法设计快回路和慢回路控制器; 其次提出基于模型逆的神经网络非线性直接自适应控制方案, 设计一种在线神经网络用于补偿模型逆误差。仿真表明, 该控制方案具有较好的自适应能力和鲁棒性。     

利用飞轮的航天器姿态跟踪与能量存储

研究航天器集成能量与姿态控制系统中飞轮的控制律。系统中飞轮是姿态控制的执行机构,同时也是储能装置。首先利用Lyapunov方法设计了航天器姿态跟踪的反馈控制律,然后研究一种力矩形式的飞轮控制律。利用奇异值分解方法把飞轮组的控制力矩向量分解为3部分相互正交的力矩向量,一部分用来提供姿态控制力矩,一部分用来以给定的功率储能,另一部分完成轮速平衡以避免由于各飞轮轮速差异过大引起的飞轮饱和。提出了一种基于动能反馈的储能功率规划方案来保证系统的能量平衡,可以避免由于过剩能量引起的飞轮饱和。数值仿真结果验证了控制方案的有效性。     

Integrated active fault-tolerant control using IMM approach

An integrated fault detection, diagnosis, and reconfigurable control scheme based on interacting multiple model (IMM) approach is proposed. Fault detection and diagnosis (FDD) is carried out using an IMM estimator. An eigenstructure assignment (EA) technique is used for reconfigurable feedback control law design. To achieve steady-state tracking, reconfigurable feedforward controllers are also synthesized using input weighting approach. The developed scheme can deal with not only actuator and sensor faults, but also failures in, system components. To achieve fast and reliable fault detection, diagnosis, and controller reconfiguration, new fault diagnosis and controller reconfiguration mechanisms have been developed by a suitable combination of the information provided by the mode probabilities from the IMM algorithm and an index related to the closed-loop system performance. The proposed approach is evaluated using an aircraft example, and excellent results have been obtained     

基于 Nussbaum函数的多无人机预设性能反步容错协同控制

针对多无人机协同执行任务过程中遭遇执行器增益故障下的安全飞行控制问题,设计了 1种预设性能反步容错姿态跟踪控制方案,以实现故障下的多无人机姿态同步跟踪控制。首先,定义飞行器的姿态同步跟踪误差和姿态角速率跟踪误差,分别利用预设性能函数对 2种误差进行约束,将不等式约束转化为等式约束。其次,基于转换误差设计反步容错姿态同步跟踪控制器,应用 Nussbaum函数解决由增益故障引起的未知控制增益问题。Lyapunov稳定性分析表明,姿态同步跟踪误差与姿态角速率跟踪误差稳定且收敛。仿真结果验证了控制方案的可行性以及有效性。     

Gain-scheduled state feedback control design technique for flightvehicles

For multi-input, multi-output (MIMO) nonlinearly parameter dependent linear parameter-varying (LPV) systems with multiple parameters, a design method of gain-scheduled state feedback control using a minimum sensitivity eigenvalue assignment of the frozen parameter closed-loop system with quadratic stability checks is proposed. The proposed design method is applied to the bank-to-turn (BTT) control of a flight vehicle, and the nonlinear 6 degree of freedom (DOF) simulations are performed to show the usefulness as a gain-scheduled state feedback control scheme     

Sensitivity Reduction in Aircraft Control Systems

A method for reducing trajectory sensitivity to parameter perturbations for linear feedback systems is described. Application of the method to the design of aircraft control systems, with special reference to a helicopter forward flight control system, is illustrated. The response of the system based on this method is found to be better than that obtained with fixed-feedback gain controllers, although the response may not be as good as that of an adaptive control scheme. The main advantage of the method is the simplicity of its implementation relative to that of the adaptive control scheme which requires an on-board computer.     

ROBUST ADAPTIVE BANK-TO-TURN MISSILE AUTOPILOT DESIGN USING FUZZY CMAC NEURAL NETWORKS

ＲＯＢＵＳＴＡＤＡＰＴＩＶＥＢＡＮＫ┐ＴＯ┐ＴＵＲＮＭＩＳＳＩＬＥＡＵＴＯＰＩＬＯＴＤＥＳＩＧＮＵＳＩＮＧＦＵＺＺＹＣＭＡＣＮＥＵＲＡＬＮＥＴＷＯＲＫＳＺｈａｎｇＹｏｕａｎ（张友安）,ＣｕｉＰｉｎｇｙｕａｎ（崔平远）,ＷａｎｇＳｈｏｕｂｉｎｇ（王守斌...     

存储系统中两级纠错编码方案设计与验证

针对恶劣空间环境设计了一种两级存储编码方案，以应对航天系统中存储单元发生多个单粒子翻转（SEU）错误的问题。方案设计的主要思想是根据简单低纠错编码组合出高容错编码，通过编码组合，使用字间编码来纠正字内编码无法纠正的错误，从而使存储系统更加可靠；对两级编码方案提出若干优化策略，以提高编解码性能，使得两级冗余编码效率接近于原始字内编码。实验结果表明，提出的两级冗余编码方案能够较好解决存储系统中发生多个单粒子翻转错误的问题。即与单一的字内编码相比，两级纠错编码方案能够大大降低星上存储系统出现不可修复的概率，保证了星上存储系统的可靠运行。     

系统误差条件下的多运动站无源定位性能分析

 系统误差的存在可能对无源定位的性能带来较大影响。针对多运动站得到的含有系统误差的观测量信息,推导了定位误差的克拉美-罗下限(CRLB)。首先根据具体系统误差模型推导测量误差的统计信息,然后根据系统误差导致不同时刻观测量相关的特点,将非对角矩阵的误差协方差矩阵写为分块矩阵的形式,并在此基础上推导其递推计算式,最后以系统误差情况下多运动站只测角无源定位为例进行定位性能的仿真分析。仿真结果表明系统误差的存在对定位误差CRLB影响较大,在定位中需要重点考虑。     

`And we were tired': fatigue and aircrew errors

It is argued, on the basis information obtained by the NASA Aviation Safety Reporting System (ASRS), that the majority of errors made by aircrew members are cognitive errors, not control errors, and that a major contributing factor is fatigue. The ASRS incident reports indicate some aircrews often receive less than six hours of sleep, experience desynchronosis, and lack proper nutrition. The ways in which all these factors affect both individual performance and group (crew) performance are discussed     

压电陶瓷叠层作动器迟滞蠕变非线性自适应混合补偿控制方法

压电陶瓷叠层作动器的迟滞蠕变非线性特性严重影响了控制系统的稳定性及动态跟踪精度。针对其迟滞蠕变非线性补偿控制问题,提出了一种高精度动态补偿压电陶瓷叠层作动器非线性特性的自适应混合补偿控制方法,即迟滞蠕变前馈补偿与自适应滤波反馈补偿结合的前馈-反馈混合控制方法。采用改进的Prandtl-Ishlinskii（Modified Prandtl-Ishlinskii,MPI）模型对压电陶瓷叠层作动器迟滞蠕变非线性特性进行精细化建模,并得到其逆补偿模型进行前馈补偿。根据前馈补偿误差,采用自适应滤波反馈控制对输入信号进行实时调控,实现对压电陶瓷叠层作动器的迟滞非线性及lg（t）型蠕变特性的实时精确补偿控制。数值仿真与实验结果表明,相比于常规前馈迟滞蠕变补偿,所提出的自适应混合补偿控制方法可以有效降低压电陶瓷叠层作动器的迟滞补偿误差,极大提高了迟滞蠕变非线性动态跟踪精度以及自适应性。     

一种变输入参数结构的多控制器协调工作设计

1引言随着航空发动机的发展,其控制系统的复杂程度不断提高[1],多个控制器组成的控制系统中,各个控制器如何协调工作的问题已越来越突出[2,3]。通过对具体航空发动机控制系统的仿真,发现问题主要集中在两个方面,一是备份控制器接替工作时其累积的输出误差很大,在短时间内无法迅     

Design of Time-constrained Guidance Laws via Virtual Leader Approach

Guidance problems with flight time constraints are considered in this article. A new virtual leader scheme is used for design of guidance laws with time constraints. The core idea of this scheme is to adopt a virtual leader for real missiles to convert a guidance problem with time constraints to a nonlinear tracking problem, thereby making it possible to settle the problem with a variety of control methods. A novel time-constrained guidance (TCG) law, which can control the flight time of missiles to a prescribed time, is designed by using the virtual leader scheme and stability method. The TCG law is a combination of the well-known proportional navigation guidance(PNG) law and the feedback of flight time error. What's more, this law is free of singularities and hence yields better performances in comparison with optimal guidance laws with time constraints. Nonlinear simulations demonstrate the effectiveness of the proposed law.     

基于预测控制的导弹俯仰通道制导控制一体化设计

考虑制导和控制之间固有的时间尺度差异,提出基于预测控制设计制导控制一体化策略,通过对动态调节过程的合理预测,更加真实的反应控制量对系统状态的影响。利用连续时间非线性预测控制,以输出跟踪误差和控制能量的组合为性能指标,在线滚动优化得到控制指令,分析了控制律的参数选取,最后通过数值仿真验证了制导控制一体化策略的有效性。