Experimental research on electrochemical machining of titanium alloy Ti60 for a blisk

Ti60(Ti–5.6Al–4.8Sn–2Zr–1Mo–0.35Si–0.7Nd) is a high-temperature titanium alloy that is now used for important components of aircraft engines. Electrochemical machining(ECM) is a promising technique that has several advantages, such as a high machining rate, and can be used on a wide range of difficult-to-process materials. In this paper, orthogonal experiments are conducted to investigate ECM of Ti60, with the aim of determining the influences of some electrochemical process parameters on the surface roughness. The most important parameter is found to be the frequency of the pulsed power supply. It is found that using suitably optimized parameters for ECM can greatly decrease the surface roughness of a workpiece. A surface roughness of approximately 0.912 lm can be obtained with the following optimal parameters: Na Cl electrolyte concentration 13wt%, voltage20 V, pulse frequency 0.4 k Hz, duty cycle 0.3, temperature 23 °C, and anode feed rate 0.5 mm/min.Furthermore, blisk blades have been successfully processed using these optimized parameters.     

Experimental investigation of rotary sinking electrochemical discharge milling with high-conductivity salt solution and non-pulsed direct current

Electrochemical milling is a modified technique of traditional electrochemical machining (ECM) that can be used to manufacture some helicopter transmission system parts. The use of rotary tools and an inner-jet electrolyte supply pattern can greatly improve the material removal rate (MRR) in a single pass. However, the feed speed is generally limited to minimize the tool wear. To increase the MRR, electrical discharge machining (EDM) is introduced into the electrochemical milling process. The tool rotation is employed to interrupt the discharge and the high-conductivity salt solution and non-pulsed direct current power supply are also adopted to increase ECM, eventually, a new machining method is proposed, which can be called rotary sinking electrochemical discharge milling (RSECD milling). The mechanism of it is explored in this study by analyzing the machined current, MRR, surface morphology, and tool wear at different applied voltages and feed speeds. Besides, the RSECD milling using the tool with a larger diameter is also conducted to further verify the effectiveness. In particular, the MRR can be increased by 742.5% when using the tool with a diameter of 20 mm at the applied voltage of 20 V.     

Surface-improvement mechanism of hybrid electrochemical discharge process using variable-amplitude pulses

Superalloys are commonly used in aircraft manufacturing; however, the requirements for high surface quality and machining accuracy make them difficult to machine. In this study, a hybrid electrochemical discharge process using variable-amplitude pulses is proposed to achieve this target. In this method, electrochemical machining (ECM) and electrical discharge machining (EDM) are unified into a single process using a sequence of variable-amplitude pulses such that the machining process realizes both good surface finish and high machining accuracy. Furthermore, the machining mechanism of the hybrid electrochemical discharge process using variable-amplitude pulses is studied. The mechanism is investigated by observations of machining waveforms and machined surface. It is found that, with a high-frequency transformation between high- and low-voltage waveforms within a voltage cycle, the machining mechanism is frequently transformed from EDM to pure ECM. The critical discharge voltage is 40 V. When pulse voltages greater than 40 V are applied, the machining accuracy is good; however, the surface has defects such as numerous discharge craters. High machining accuracy is maintained when high-voltage pulses are replaced by low-voltage pulses to enhance electrochemical dissolution. The results indicate that the proposed hybrid electrochemical discharge process using variable-amplitude pulses can yield high-quality surfaces with high machining accuracy.     

整体叶盘叶型电解加工流场设计及实验简

 电解加工（ECM）是航空发动机整体叶盘制造的主要技术之一,其电解液流场稳定性是影响电解加工精度和表面质量的核心因素。本文在分析原有的二维流场基础上,针对流体在不同流道截面下的流场状态,提出了一种三维复合电解液流场模式,即三股电解液分别从毛坯进气边、叶盆叶根、叶背叶根流入,由排气边交汇流出。采用有限元法对三维复合流场及两类二维流场开展仿真分析,分析结果表明三维复合流场改善了流道突变区域流场状态,有效抑制了二维流场的流场缺陷,有助于提高流场稳定性。对加工区液体流态进行了判断,其结果显示三维复合流场可以满足电解加工要求。开展了3种流场模式的加工速度比较实验,三维复合流场达到的进给速度最高,较二维流场可显著提升加工效率。采用三维复合流场开展了多叶片扇段加工,获得了较好的重复精度与表面质量。     

整体叶盘叶型电解加工流场设计及实验

电解加工（ECM）是航空发动机整体叶盘制造的主要技术之一,其电解液流场稳定性是影响电解加工精度和表面质量的核心因素。本文在分析原有的二维流场基础上,针对流体在不同流道截面下的流场状态,提出了一种三维复合电解液流场模式,即三股电解液分别从毛坯进气边、叶盆叶根、叶背叶根流入,由排气边交汇流出。采用有限元法对三维复合流场及两类二维流场开展仿真分析,分析结果表明三维复合流场改善了流道突变区域流场状态,有效抑制了二维流场的流场缺陷,有助于提高流场稳定性。对加工区液体流态进行了判断,其结果显示三维复合流场可以满足电解加工要求。开展了3种流场模式的加工速度比较实验,三维复合流场达到的进给速度最高,较二维流场可显著提升加工效率。采用三维复合流场开展了多叶片扇段加工,获得了较好的重复精度与表面质量。     

Simulation and experimental investigation on a dynamic lateral flow mode in trepanning electrochemical machining

An appropriate flow mode of electrolyte has a positive effect on process efficiency, surface roughness, and machining accuracy in the electrochemical machining(ECM) process. In this study, a new dynamic lateral flow mode, in which the electrolyte flows from the leading edge to the trailing edge, was proposed in trepanning ECM of a diffuser. Then a numerical model of the channel was set up and simulated by using computational fluid dynamics software. The result showed that the distribution of the flow field was comparatively uniform in the inter-electrode gap. Furthermore, a fixture was designed to realize this new flow mode and then corresponding experiments were carried out. The experimental results illustrated that the feeding rate of the cathode reached 2 mm/min, the best taper angle was about 0.4°, and the best surface roughness was up to Ra= 0.115 lm. It reflects that this flow mode is suitable and effective, and can also be applied to machining other complex structures in trepanning ECM.     

Electrochemical trepanning with uniform electrolyte flow around the entire blade profile

In the traditional machining process for diffusers, blades are easily deformed, and methods suffer from high tool wear and low efficiency. Electrochemical machining(ECM) possesses unique advantages when applied to these difficult-to-machine materials. In the ECM process, theflow field plays a crucial role. Here, an electrolyte flow mode that supplies uniform flow around the entire blade profile was adopted for electrochemical trepanning of diffusers. Various flow rates were employed to obtain the optimal flow field. Simulations were conducted using ANSYS software, and results indicated that increasing the flow rate substantially afforded a more uniform flowfield. A series of experiments was then performed, and results revealed that increasing the flow rate greatly improved both the machining efficiency and the surface quality of the diffusers. The maximum feeding rate of the cathode reached 4 mm/min, the blade taper of the concave part decreased to 0.02, and the blade roughness was reduced to 1.216 lm. The results of this study demonstrated the high feasibility of this method and its potential for machining other complex components for engineering applications.     

Optimization of flow field in electrochemical trepanning of integral cascades (Ti6Al4V)

Ti6Al4V is widely applied in the integral cascades of aero engines. As an effective machining method, electrochemical trepanning (ECTr) has unique advantages in processing surface parts made of hard-to-cut materials. In ECTr, the state of the flow field has a significant effect on processing stability and machining quality. To improve the uniformity of the flow field when ECTr is applied to Ti6Al4V, two different flow modes are designed, namely full-profile electrolyte supply (FPES) and edges electrolyte supply (EES). Different from the traditional forward flow mode, the flow directions of the electrolyte in the proposed modes are controlled by inlet channels. Simulations show that the flow field under EES is more uniform than that under FPES. To further enhance the uniformity of the flow field, the structure of EES is optimized by modifying the insulating sleeve. In the optimized configuration, the longitudinal distance between the center of the inlet hole and the center of the blade is 6.0 mm, the lateral distance between the centers of the inlet holes on both sides is 16.5 mm, the length to which the electrolyte enters the machining area is 1.5 mm, and the height of the insulating sleeve is 13.5 mm. A series of ECTr experiments are performed under the two flow modes. Compared with EES, the blade machined by FPES is less accurate and has poorer surface quality, with a surface roughness (R_a) of 3.346 μm. Under the optimized EES, the machining quality is effectively enhanced, with the surface quality improved from R_a = 2.621 μm to R_a = 1.815 μm, thus confirming the efficacy of the proposed methods.     

Flow field design and experimental investigation of electrochemical machining on blisk

Flow field is a crucial factor to influence the stability and surface quality in the electrochemical machining (ECM) of blisks. A four-way flow mode was proposed to eliminate mixing regions of electrolyte at the leading and tailing edges. Two flow field models were described separately in this report: a W-shaped flow mode and a four-way flow mode. The flow field was analyzed through a finite element method. The results showed that, in comparison with the W-shaped flow mode, the distribution of electrolyte flow was more uniformed and the mixed region in the flow channel was improved. The pressure of the leading and tailing edges inlets was optimized, and optimal pressure of 0.6 MPa was determined. In addition, verification experiments were performed, and the results showed that the stability, efficiency, and quality of the profiles of the blisk blade manufactured by ECM were enhanced in the new flow mode.     

Improving profile accuracy and surface quality of blisk by electrochemical machining with a micro inter-electrode gap

Electrochemical machining (ECM) has emerged as an important option for manufacturing the blisk. The inter-electrode gap (IEG) distribution is an essential parameter for the blisk precise shaping process in ECM, as it affects the process stability, profile accuracy and surface quality. Larger IEG leads to a poor localization effect and has an adverse influence on the machining accuracy and surface quality of blisk. To achieve micro-IEG (<50 μm) blisk finishing machining, this work puts forward a novel variable-parameters blisk ECM strategy based on the synchronous coupling mode of micro-vibration amplitude and small pulse duration. The modelling and simulation of the blisk micro-IEG machining have been carried out. Exploratory experiments of variable-parameters blisk ECM were carried out. The results illustrated that the IEG width reduced with the progress of variable parameter process. The IEG width of the blade’s concave part and convex part could be successfully controlled to within 30 μm and 21 μm, respectively. The profile deviation for the blade’s concave surface and convex surface are 49 μm and 35 μm, while the surface roughness reaches R_a = 0.149 μm and R_a = 0.196 μm, respectively. The profile accuracy of the blisk leading/trailing edges was limited to within 91 μm. Compared with the currently-established process, the profile accuracy of the blade’s concave and convex profiles was improved by 50.5 % and 53.3 %, respectively. The surface quality was improved by 53.2 % and 50.9 %, respectively. Additionally, the machined surface was covered with small corrosion pits and weak attacks of the grain boundary due to selective dissolution. Some electrolytic products were dispersed on the machined surface, and their components were mainly composed of the carbide and oxide products of Ti and Nb elements. The results indicate that the variable-parameters strategy is effective for achieving a tiny IEG in blisk ECM, which can be used in engineering practice.     

Electrochemical machining of a convex strips structure on a revolving part by using site directed power interruption

Revolving parts with complex surface structures are widely used in machinery and mechanical equipment. The ECM process provides its adequacy to cut hard materials with different shapes, and its applications are widely increased, due to its outstanding advantages. In this paper, a new method for machining a convex strips structure on a cylinder by using site directed power interruption(SDPI) in the ECM process is presented. A variable correction value of the power-off time was defined and optimized to obtain the ideal interval for better machining accuracy and stability.The electric field distribution and the simulated convex profiles show that the stray current density can be reduced effectively by using the proposed method. The correction value has an important influence on the machining accuracy. A suitable correction value in the range of 0.6–1.2 s can effectively improve the machining accuracy of the convex strips structure. Experiments were also conducted to verify the proposed method. Results have confirmed that the stray corrosion on the convex strips surface is significantly reduced and the machining accuracy of convex strips structure is remarkably improved by using the proposed method with a suitable correction value in the ECM process. Finally, a convex strip with a height of 2 mm on a thin-wall revolving part was also produced successfully using a correction value of 0.9.     

Simulation and experimental investigation of inner-jet electrochemical grinding of GH4169 alloy

GH4169 alloy is one of the most commonly used materials in aero engine turbine blades, but its machinability is poor because of its excellent strength at high temperatures. Electrochemical machining (ECM) has become a common method for machining this alloy and other difficult-to-machine materials. Electrochemical grinding (ECG) is a hybrid process combining ECM and conventional grinding. In this paper, investigations conducted on inner-jet ECG of GH4169 alloy are described. Two types of inner-jet ECG grinding wheels were used to machine a flat bottom surface. The machining process was simulated using COMSOL software, and machining gaps under different machining parameters were obtained. In addition, maximum feed rates and maximum material removal rates under different machining parameters were studied experimentally. The maximum sizes and the uniformity of the distributions of the gaps machined by the two grinding wheels were compared. The effects of different applied voltages on the machining results were also investigated.     

Electrochemical machining of complex components of aero-engines: Developments,trends, and technological advances

Because of several advantages, such as no tool wear, independence on the mechanical properties of the material, and high machining efficiency, electrochemical machining (ECM) has become a viable method for machining components in numerous industrial applications, particularly in the manufacture of typical aero-engine components with complex structures fabricated from materials that are difficult to cut. This paper highlights the current developments, new trends, and technological advances of key factors of ECM, such as electrochemical dissolution characteristics of novel difficult to cut materials which are often used in aero-engine, numerical simulation of electrochemical process, design for the complex profile and structure of cathode tool, flow field simulation and design for uniform electrolyte flow, and innovation of electrochemical machining or hybrid methods which reflect the state of the art in academic and industrial research on electrochemical machining in aero-engine manufacturing.     

脉冲电流大厚度电解线切割加工试验

航空航天难加工材料直纹面构件的高精度高表面完整性加工已经成为制造领域普遍关注和亟需解决的难题，电解线切割加工在高表面完整性要求加工场合上具有原理性优势。建立脉冲电流电解线切割加工模型，分析了工件厚度变化带来的影响。试验结果表明：随着工件厚度增加，电解液电阻减小，工件两端极间电压减小，加工缝宽变窄；双电层时间常数增大，脉宽时间内充电所能达到的电位降低，有效加工时间变短，平均电流密度较低；脉冲频率大于20 kHz时，最大进给速度随频率增加而快速减小，低于20 kHz时，最大加工速度差别较小。最后，采用脉冲频率20 kHz，以进给速度4 μm/s稳定加工出20 mm厚榫头/榫槽结构，表面粗糙度约为0.449 4 μm，表面质量、加工效率明显高于100 kHz加工效果。     

Electrochemical machining on blisk channels with a variable feed rate mode

Electrochemical machining (ECM) is an economical and effective method for blisk manufacturing and includes two steps: channel machining and profile machining. The allowance distribution after the channel machining will directly affect the profile machining. Therefore, to improve the uniformity of allowance distribution in the machining of channels, a method that incorporates a variable feed rate mode is developed. During the machining process, the feed rates are dynamically changed according to the needs of the side gap at the different feed depths. As a result, the side gaps at the different feed depths vary, contributing to a decrease in the allowance difference. In this study, the dissolution processes of a blisk channel are simulated using different feed rates, and prediction profiles are obtained. Based on the prediction profiles, the relationship among the feed rate, feed depth, and side gap is established. Then, the feed rates at different feed depths are adjusted according to the relationship. In addition, contrast experiments are conducted. Compared with blisk channel ECM using a constant feed rate of 1 mm/min, using the variable feed rate decreases the allowance differences in the convex and concave parts by 62.2 % and 67.4 %, respectively. This indicates that using the variable feed rate in the ECM process for a blisk channel is feasible and efficient.     

Effect of tube-electrode inner diameter on electrochemical discharge machining of nickel-based superalloy

Nickel-based superalloys are widely employed in modern aircraft engines because of their excellent material characteristics, particularly in the fabrication of film cooling holes. How-ever, the high machining requirement of a large number of film cooling holes can be extremely chal-lenging. The hybrid machining technique of tube electrode high-speed electrochemical discharge drilling (TEHECDD) has been considered as a promising method for the production of film cooling holes. Compared with any single machining process, this hybrid technique requires the removal of more complex machining by-products, including debris produced in the electrical discharge machin-ing process and hydroxide and bubbles generated in the electrochemical machining process. These by-products significantly affect the machining efficiency and surface quality of the machined prod-ucts. In this study, tube electrodes in different inner diameters are designed and fabricated, and the effects of inner diameter on the machining efficiency and surface quality of TEHECDD are inves-tigated. The results show that larger inner diameters could effectively improve the flushing condi-tion and facilitate the removal of machining by-products. Therefore, higher material removal efficiency, surface quality, and electrode wear rate could be achieved by increasing the inner diam-eter of the tube electrode.     

Comparative investigation on high-speed grinding of TiCp/Ti–6Al–4V particulate reinforced titanium matrix composites with single-layer electroplated and brazed CBN wheels

In order to develop the high-efficiency and precision machining technique of Ti Cp/Ti–6Al–4V particulate reinforced titanium matrix composites(PTMCs), high-speed grinding experiments were conducted using the single-layer electroplated cubic boron nitride(CBN) wheel and brazed CBN wheel, respectively. The comparative grinding performance was studied in terms of grinding force, grinding temperature, grinding-induced surface features and defects. The results display that the grinding forces and grinding temperature obtained with the brazed CBN wheel are always lower than those with the electroplated CBN wheel. Though the voids and microcracks are the dominant grinding-induced surface defects, the brazed CBN wheel produces less surface defects compared to the electroplated wheel according to the statistical analysis results. The maximum materials removal rate with the brazed CBN wheel is much higher than that with the electroplated one. All above indicate that the single-layer brazed CBN super-abrasive wheel is more suitable for high-speed grinding of PTMCs than the electroplated counterpart.     

Improving performance of macro electrolyte jet machining of TC4 titanium alloy: Experimental and numerical studies

Electrolyte jet machining (EJM) is a promising method for shaping titanium alloys due to its lack of tool wear, thermal and residual stress, and cracks and burrs. Recently, macro-EJM has attracted increasing attention for its high efficiency in machining wide grooves or planes. However, macro-EJM generates large amounts of electrolytic products, thereby increasing the difficulty of rapid product removal with a standard tool and reducing the surface quality. Therefore, for enhanced product transport, a novel tool with a back inclined end face was proposed for macro-EJM of TC4 titanium alloy. For comparison, also proposed were ones with a standard flat end face, a front inclined end face, and both front and back inclined end faces. The flow field distributions of all proposed tools were simulated numerically, and experiments were also conducted to validate the simulation results. The results show that one with a 5° back inclined end face can decrease the low-velocity flow zone in the machining area and increase the high-velocity flow zone at the back end of tool, thereby promoting rapid product removal. A relatively smooth bright-white groove surface was obtained. The same tool also resulted in the highest machining depth and material removal rate among the tested ones. In addition, rapid product removal was beneficial to the subsequent processing. Because of its rapid product removal, the machining depth and material removal rate during deep groove machining using the tool with a 5° back inclined end face were respectively 7% and 14% higher than those produced using a standard one. Moreover, the lowest bottom height difference of 0.027 mm can be obtained when the step-over value was 8.2 mm, and a plane with a depth of 0.285 mm and a bottom height difference of 0.03 mm was fabricated using the tool with a 5° back inclined end face.     

Flow field design and process stability in electrochemical machining of diamond holes

The metal grille, commonly composed of an amount of diamond holes, has been grow-ingly used as a key structure on stealth aircraft. Electrochemical machining (ECM) promises to be increasingly applied in aircraft manufacturing on the condition that process stability is guaranteed. In this work, a flow field model was designed to improve the process stability. This model is endowed with a variety of flow channel features, together with vibrating feeding modes. The flow field distribution on the bottom surface of the diamond hole was discussed and evaluated as well. The numerical results show that a short arc flow channel could significantly enhance the uniformity of electrolyte velocity distribution and a vibrating feeding of the cathode enables to reduce both fluctuations of the electrolyte velocity and pressure on the bottom surface of the diamond hole. Consequently, the flow field mutations were eliminated. It is verified from the experimental results that a short arc flow channel, when combined with vibrating feeding, is capable of improving machining localization and process stability markedly. What is more, the side gap on the bottom surface of the diamond hole could also be reduced by the abovementioned approach.     

Electrochemical drilling of small holes by regulating in real-time the electrolyte flowrate in multiple channels

Electrochemical drilling(ECD) provides an alternative technique for drilling multiple small holes in difficult-to-machine materials in numerous industrial applications such as for aeroengines. The value and fluctuation of electrolyte flowrate can seriously affect the machining stability and hole quality in ECD. In particular, when drilling multiple holes, the distribution and fluctuations of the electrolyte flowrate in each channel could influence the uniformity of the electrolyte flowrate among...