基于FPGA的超声三维坐标测量系统

提出基于超声波测距的三维坐标测量方法,利用FPGA实现超声波测距系统电路,设计并行四个通道信号处理系统,获得超声发射端到四个超声接收端的距离,并利用最小二乘法实现发射端空间位置的准确估计。对基于超声波测距的三维坐标测量系统进行实验研究,实验结果表明采用峰值测距和最小二乘三维定位算法可有效实现三维坐标测量,坐标的绝对误差在30 mm以内。     

一种TPC编译码器的FPGA设计实现

简要介绍了Turbo乘积码的编译码原理,提出了一种基于AHA4540和FPGA的TPC编译码器设计方案.重点给出了TPC编码器的FPGA编程设计的思想以及AHA4540内部寄存器的配置设计,并对所设计配置后的编译码器进行了仿真验证.结果表明,该设计系统具有良好的性能.     

导弹电磁弹射器电磁兼容性研究

在导弹电磁弹射器发射过程中会产生强电磁场辐射,不仅会造成电磁能量的损耗,也会对系统中的电子设备产生干扰。因此,在电磁发射中需要采取一定的防护措施。文章分析了导弹电磁弹射系统的组成和工作原理,从发射线圈电磁屏蔽和电路中的抗干扰2个方面对电磁线圈的电磁兼容性设计进行研究,并进行了仿真分析,通过比对屏蔽前后的效果,给出了一种磁线圈弹射器电磁兼容性设计的解决方案。     

基于FPGA的FIR滤波器设计与实现

本文根据激光陀螺仪信号的解调原理,提出了一种利用数字信号处理技术并采用FPGA实现的解调方法。分析了FIR滤波器的工作原理,根据激光陀螺仪对滤波器的要求,给出了由FPGA设计实现FIR滤波器的基本原理,并利用IP核实现了FIR滤波器,满足了激光陀螺仪的需求。通过在国产激光陀螺仪上的应用,验证了方案的正确性。通过对激光陀螺仪脉冲计数的高速采样并利用数字滤波器处理,可以有效的消除抖动引起的信号噪声,得到所需要的惯性信息。采用FPGA设计实现,可以提高运算速度,并且可以缩短数据采样的延时。     

基于FPGA的边界扫描测试系统的研究

介绍了基于FPGA的边界扫描测试系统的系统组成,工作原理,以及设计方案。描述了嵌入式测试系统的软硬件设计。文章给出了系统的程序流程和数据结构。     

电磁发射拦截装置中发射线圈的结构分析

介绍了电磁发射拦截装置的组成及工作原理,建立了发射线圈的三维模型,对发射线圈进行了磁—结构耦合分析,给出了发射线圈的磁场和应力场分布规律,得出了初步结论。     

一种用于 ACAS 的相位校准方法

校准是用于 ACAS 发射机的一项关键技术,本文给出了一种新的基于比相的实时校准方法,去除了发射通道幅度对通道相位差的影响,介绍了该方法的原理,并在 FPGA 硬件平台上完成了该方法的仿真和验证,通过实测数据的分析与处理,证明了这种方法的可行性     

基于FPGA和DSP的光电吊舱控制系统设计与实现

本文介绍了机载两框架两轴光电吊舱的工作原理,并设计了一种基于FPGA和DSP的光电吊舱控制系统,充分利用了FPGA和DSP的各自优势,提高了系统的响应速度。详细描述了控制系统硬件电路的功能划分和实现过程。提出了控制回路设计方案,并通过实验验证了控制系统的性能,在两框架两轴光电吊舱上实现了较高的光轴稳定精度     

一种采用收发双缓冲结构的1553B总线接口的设计与实现

从简化结构、提高实时性的角度出发,提出了一种RT模式下的1553B总线接口。该总线接口硬件上以BU-61580为总线协议处理器,以FPGA为主处理器,在FPGA内部实现接口粘合逻辑,省去额外电路,做到无缝链接。软件上在接收端采用子地址双缓冲模式,保证数据一致性和正确性,发送端提出了发送双缓冲机制,在保证可靠性的前提下提高了数据更新的实时性。详细阐述了总线接口的设计和实现方案,并通过仿真和实验手段证明了该接口方案的可行性和有效性。     

一种截获高速机动目标的方法

分析了采用滤波器组的方法截获快速机动目标存在的缺点,提出通过采用对回波信号进行FFT提取多普勒频移的方法得到目标的径向速度,并介绍了基4FFT算法原理,给出了采用FPGA设计FFT的方法。     

基于飞机油箱模型形状特征油量测量切片步长选择方法研究

 在分析飞机数字式油量测量过程中目前广泛使用的切片法油量测量原理的基础上,针对现有的定步长切片法无法得到准确、可靠的燃油质量特性数据库的缺陷,结合对飞机油箱模型形状特征的分析,提出了基于飞机油箱模型形状特征的油量测量切片步长选择方法。此方法包括切片步长整体和局部选择两个过程,整体选择以实现相邻两切片平面所夹油箱模型体积近似相等为目的来确定切片步长,以体现油箱模型截面整体变化规律;局部选择以设计切片平面与截面突变平面重合或尽可能接近的方式,突出油箱截面的局部变化特征。实验结果表明：该切片步长选择方法较定步长方法能够建立更为合理、可靠的燃油质量特性数据库,从而提高了油量测量精度。     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

二维翼段颤振的μ控制

 采用超声电机作为作动器来实现含控制面的翼段颤振鲁棒抑制。针对作者设计的二维翼段颤振主动抑制系统，通过理论与实验相结合的方法，建立了考虑沉浮方向阻尼和作动器模型参数不确定性的控制系统模型，设计了μ控制器，并对控制器做了降阶处理。数值仿真和风洞试验表明，μ控制器可有效地抑制颤振的发生，将颤振临界速度提高23.4%。相对于H_∞控制器，μ控制器的控制效果和鲁棒性更好。     

Abnormal Shape Mould Winding

为解决网格化芯模的缠绕问题,本文提出了复合材料面片缠绕机理;接着详细分析了面片缠绕过程中的芯模凹曲面上纤维滑线和架空现象,应用微分几何曲面理论和空间几何理论,提出判据及其解决方案;最后,针对飞机发动机进气道的缠绕成型,编制缠绕控制程序并进行相应的实验,验证了面片缠绕方法的可行性。     

基于H∞性能指标的质量矩拦截弹鲁棒控制

 以所建立的质量矩拦截弹数学模型为基础，利用微分几何的反馈线性化理论，得到一个解耦线性系统，考虑到拦截弹的鲁棒性要求和3个滑块的协调控制问题，提出采用双回路的设计方法，内回路采用线性二次调节器（LQR），外回路采用考虑混合灵敏度问题的H_∞控制设计。仿真结果证明了该方法动态性能满足设计要求，同时对系统参数的不确定性具有较强的鲁棒性。     

航天器返回地球的气动特性综述

航天器返回地球的飞行过程中,气动特性是实现将宇宙飞行速度减到落地前速度、保证再入飞行得到有效控制以及再入防热安全可靠的关键因素。针对简单旋成体气动外形、半弹道式再入控制、烧蚀防热类返回航天器,综述了返回地球过程中变化的空气流域特性、航天器周围的气体绕流环境、空气与航天器作用产生的动力学与热效应等。系统地给出了该类航天器的再入气动特性参数与飞行性能的共性规律,包括:气动阻力与再入减速、气动升力与再入轨迹控制、配平攻角与飞行稳定性、气动加热与防热,以及再入过程中不同气动特性航天器、气象条件变化等对再入飞行性能的影响规律。为航天器开展返回飞行过程的跨流域气动性能工程研制提供设计参考。     

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.     

Effects of Mo on the Microstructure and Hydrogen Sorption Properties of Ti-Mo Getters

The effects of Mo on the microstructure evolution, porosity and hydrogen sorption properties of Ti-Mo getters are investigated in this work. The results show that the addition of Mo prolongs the densification process of Ti-Mo getters and results in a significant amount of sintered pores. With the Mo content increasing, the porosity of getters firstly increases reaching the maximum value as it at- tains about 7.5wt.%, and then drops. At the room temperature, the hydrogen sorption property of getters increases progressively with the Mo content increasing, but the tendency is not very clear before its content lies below 2.5wt.%. When the Mo content achieves about 7.5wt.%, the hydrogen sorption property proves to be the best. The discussion is made about the above mentioned phenomena inclusive of hydrogen sorption properties of getters under different activation conditions (from 500-750 ℃).     

Preparation of Highly Dispersed Antimony-doped Tin Oxide Nano-powder via Ion-exchange Hydrolysis of SnCl4 and SbCl3 and Azeotropic Drying

Antimony-doped tin hydroxide colloid precipitates have been synthesized by hydrolysis of SnCl4 and SbCl3 using: (1) an ion-exchange hydrolysis to remove chlorine ions, and (2) isoamyl acetate as an azeotropic solvent to obviate water. The obtained dried powder is of high dispersivity without any need for further grinding. The size and dispersivity of the final particles are investigated with the aid of TG-DTA, BET, XRD and TEM. After having calcined, the antimony-doped tin oxide nanopowder possesses a tetragonal rutile structure with high dispersivity, uniform particles and low hard agglomeration.