磁流变弹性体砂轮抛光镍基高温合金表面完整性研究

为了改善磨削后镍基高温合金GH4169的表面完整性,本文采用磁流变弹性体砂轮对镍基高温合金GH4169进行抛光试验研究。首先,通过模压成型的方法制备了磁流变弹性体砂轮,并对其表面微观形貌及不同磁场强度下的硬度进行了表征。其次将制备出的磁流变弹性体砂轮用于对镍基高温合金GH4169的抛光工艺试验中,并讨论抛光工艺参数中磁场强度对镍基高温合金表面完整性的影响。试验结果表明：在一定的磁场强度范围内,零件抛光后的表面粗糙度和显微硬度随着磁场强度的增大而减小,同时增大磁场强度也有利于改善零件的表面形貌,减少砂轮的磨损量,降低零件磨削后的亚表面损伤层厚度。     

新型刚玉砂轮磨削GH4169镍基高温合金的性能评价研究

镍基高温合金是航空发动机部件的常用材料,其磨削加工存在工具损耗严重、寿命短等难题。针对3种新研制的刚玉砂轮(分别为粒度60#的微晶和单晶混合磨料砂轮、粒度60#的单晶刚玉砂轮,以及粒度70#的单晶刚玉砂轮),开展了GH4169镍基高温合金材料的磨削试验,从磨削力、磨削温度、砂轮磨损以及表面粗糙度等方面对3种砂轮的磨削性能进行了评价。结果表明,3种砂轮磨削GH4169材料在砂轮磨损和表面粗糙度方面未表现出明显差异,而通过对磨削力和磨削温度的综合评价发现粒度60#的单晶刚玉砂轮的磨削性能更优。3种砂轮磨削GH4169材料的磨削比在0.5~3之间。在正常磨削条件下,3种砂轮的磨削表面粗糙度Ra小于0.4μm。同时发现,砂轮磨损(主要包括磨粒的破碎和脱落)是造成磨削表面缺陷形成的重要原因。     

Influence of alumina abrasive tool wear on ground surface characteristics and corrosion properties of K444 nickel-based superalloy

K444 nickel-based superalloy is an important material to manufacture the gas turbine due to its excellent mechanical properties at high temperatures and corrosion resistance. Currently,grinding is the mostly used method for the surface finish of the K444 alloy components. However,few studies worked on the effects of the abrasive tool wear on the ground surface characteristics and corrosion properties of K444 alloy. This study uses two different-type alumina abrasive tools, i.e.,white alumina(WA)...     

Grindability and Surface Integrity of Cast Nickel-based Superalloy in Creep Feed Grinding with Brazed CBN Abrasive Wheels

The technique of creep feed grinding is most suitable for geometrical shaping, and therefore has been expected to improve effectively material removal rate and surface quality of components with complex profile. This article studies experimentally the effects of process parameters (i.e. wheel speed, workpiece speed and depth of cut) on the grindability and surface integrity of cast nickel-based superalloys, i.e. K424, during creep feed grinding with brazed cubic boron nitride (CBN) abrasive wheels. Some important factors, such as grinding force and temperature, specific grinding energy, size stability, surface topography, microhardness and microstructure alteration of the sub-surface, residual stresses, are investigated in detail. The results show that during creep feed grinding with brazed CBN wheels, low grinding temperature at about 100 °C is obtained though the specific grinding energy of nickel-based superalloys is high up to 200-300 J/mm³. A combination of wheel speed 22.5 m/s, workpiece speed 0.1 m/min, depth of cut 0.2 mm accomplishes the straight grooves with the expected dimensional accuracy. Moreover, the compressive residual stresses are formed in the burn-free and crack-free ground surface.     

Grinding force and surface quality in creep feed profile grinding of turbine blade root of nickel-based superalloy with microcrystalline alumina abrasive wheels

Creep feed profile grinding of the fir-tree blade root forms of single crystal nickel-based superalloy was conducted using microcrystalline alumina abrasive wheels in the present study. The grinding force and the surface quality in terms of surface topography, subsurface microstructure, microhardness and residual stress obtained under different grinding conditions were evaluated comparatively. Experimental results indicated that the grinding force was influenced significantly by the competing predominance between the grinding parameters and the cross-sectional root workpiece profile. In addition, the root workpiece surface, including the root peak and valley regions, was produced with the large difference in surface quality due to the nonuniform grinding loads along the root workpiece profile in normal section. Detailed results showed that the surface roughness, subsurface plastic deformation and work hardening level of the root valley region were higher by up to 25%, 20% and 7% in average than those obtained in the root peak region, respectively, in the current investigation. Finally, the superior parameters were recommended in the creep feed profile grinding of the fir-tree blade root forms. This study is helpful to provide industry guidance to optimize the machining process for the high-valued parts with complicated profiles.     

镍基高温合金GH4169磨削参数对表面完整性影响

研究了用单晶刚玉砂轮磨削镍基高温合金GH4169时,磨削参数对表面完整性中的表面特征(表面粗糙度、表面形貌、表面显微硬度和表面残余应力)的影响,以期优化磨削参数.砂轮速度依次选择15,20,25m/s,磨削深度分别选择50,100,150μm,工件速度分别选择5,10,15m/min.研究结果表明:表面粗糙度对工件速度的变化最敏感,表面显微硬度对砂轮速度变化最敏感,表面残余应力对砂轮速度变化最敏感;同时表明了磨削参数对磨削表面形貌、显微硬度梯度、微观组织、残余应力梯度的影响,揭示了表面完整性中的变质层形成规律.其塑性变形层在5～10μm,显微硬度变化影响层为80～100μm,残余应力影响层厚度为80～200μm,其为磨削镍基高温合金表面完整性控制研究提供相关的实验数据基础.      

K417镍基高温合金微动磨损行为的研究

研究了K417镍基高温合金的微动磨损行为。结果表明,K417镍基高温合金的微动磨损可以分为开始、过渡和稳定三个阶段,稳定阶段的微动磨损机理是疲劳脱层。高温下K417镍基合金的微动磨损表面可以形成致密的釉质氧化膜,具有良好高温强度的K417镍基合金基体的支撑保证了釉质氧化膜的连续和完整。通过降低剪切应力的大小和改变其分布形式,釉质氧化膜可以缓解K417镍基合金的微动磨损。     

Prediction on grinding force during grinding powder metallurgy nickel-based superalloy FGH96 with electroplated CBN abrasive wheel

In this article, a grinding force model, which is on the basis of cutting process of single abrasive grains combined with the method of theoretical derivation and empirical formula by analyzing the formation mechanism of grinding force, was established. Three key factors have been taken into accounts in this model, such as the contact friction force between abrasive grains and materials, the plastic deformation of material in the process of abrasive plowing, and the shear strain effect of material during the process of cutting chips formation. The model was finally validated by the orthogonal grinding experiment of powder metallurgy nickel-based superalloy FGH96 by using the electroplated CBN abrasive wheel. Grinding force values of prediction and experiment were in good consistency. The errors of tangential grinding force and normal grinding force were 9.8% and 13.6%, respectively. The contributions of sliding force, plowing force and chip formation force were also analyzed. In addition, the tangential forces of sliding, plowing and chip formation are 14%, 19% and 11% of the normal forces on average, respectively. The pro-posed grinding force model is not only in favor of optimizing the grinding parameters and improving grinding efficiency, but also contributes to study some other grinding subjects (e.g. abrasive wheel wear, grinding heat, residual stress).     

Grain erosion wear properties and grinding performance of porous aggregated cubic boron nitride abrasive wheels

Cubic boron nitride (cBN) superabrasive grinding wheels exhibit unique advantages in the grinding of difficult-to-cut materials with high strength and toughness, such as titanium alloys and superalloys. However, grinding with multilayered metallic cBN superabrasive wheels faces problems in terms of grain wear resistance, the chip storage capability of the working layers and the stability and controllability of the dressing process. Therefore, in this work, novel metallic cBN superabrasive wheels with aggregated cBN (AcBN) grains and open pore structures were fabricated to improve machining efficiency and surface quality. Prior to the grinding trials, the air-borne abrasive blasting process was conducted and the abrasive blasting parameters were optimized in view of wear properties of cBN grains and metallic matrix materials. Subsequently, the comparative experiments were performed and then the variations in grinding force and force ratio, grinding temperature, tool wear morphology and ground surface quality of the multilayered AcBN grinding wheels were investigated during machining Ti–6Al–4V alloys. In consideration of the variations of grain erosion wear volume and material removal rate per unit of pure metallic matrix materials as the abrasive blasting parameters changes, the optimal abrasive blasting parameters were identified as the SiC abrasive mesh size of 60# and the abrasive blasting distance and time of 60 mm and 15 s, respectively. The as-developed AcBN grains exhibited better fracture toughness and impact resistance than monocrystalline cBN (McBN) grains because of the existence of metal-bonded materials amongst multiple cBN particles that decreased crack propagation inside whole grains. The metallic porous AcBN wheels had lower grinding forces and temperature and better ground surface quality than vitrified McBN wheels due to the constant layer-by-layer exposure of cBN particles in the working layer of AcBN wheels.     

单颗磨粒磨削仿真研究进展

概述了传统磨削仿真的基本方法及发展过程,总结了磨粒模型和工件模型的研究现状,具体分析了有限元法、光滑流体粒子动力学法、分子动力学法以及综合仿真方法等应用于单颗磨粒磨削材料的去除机理、成屑机理、工件表面质量以及磨粒磨损等仿真中的研究现状,最后阐述了各类仿真方法的局限性,并提出了单颗磨粒磨削仿真进一步的发展前景。     

Development of a new high-shear and low-pressure grinding wheel and its grinding characteristics for Inconel718 alloy

Nickel-based alloy has been widely used due to its outstanding mechanical properties. However, Nickel-based alloy is a typical difficult-to-machine material, which is a great constrain for its application in the manufacturing field. To improve the surface quality of the ground workpiece, a new high-shear and low-pressure grinding wheel, with high ratio of tangential grinding force to normal grinding force, was fabricated for the grinding of selective laser melting (SLM) manufactured Inconel718 alloy. The principle of high-shear and low-pressure grinding process was introduced in detail, which was quite different from the conventional grinding process. The fabrication process of the new grinding wheel was illustrated. A serial of experiments with different processing parameters were carried out to investigate the grinding performance of the developed grinding wheel via analyzing surface roughness and surface morphology of the ground workpiece. The optimal processing parameters of high-shear and low-pressure grinding were obtained. The surface roughness of ground workpiece was reduced to 0.232 μm from the initial value of 0.490 μm under the optimal grinding conditions. It was found that the initial scratches on the ground workpiece were almost completely removed after the observations with the metalloscopy and the field-emission scanning electron microscopy (FE-SEM). The capability of the newly developed high-shear and low-pressure grinding wheel was validated.     

摩擦系数对燕尾榫微动疲劳特性的影响

在燕尾榫连接接头的微动疲劳特性分析中,考虑接触表面质量,即摩擦系数的影响.给出了摩擦系数对接头应力水平、摩擦功和微动磨损参数之间的关系.分析表明：按照传统方法,将摩擦系数取为常数时所确定的裂纹萌生位置偏于危险,由于摩擦系数的变化,裂纹既可能在榫头上萌生,也可能在榫槽上萌生;摩擦系数对接头的切向应力和摩擦功等参数也有一定的影响.     

钛合金风扇叶片磨抛加工性能试验研究

针对钛合金风扇叶片磨抛加工中砂轮易磨损、工件表面易烧伤的问题,开展了钛合金材料磨抛加工性试验研究,主要考察砂轮选型、磨抛工艺参数等关键因素对钛合金材料磨抛加工性的影响,并对试验结果进行了分析研究。试验结果表明,在保证工件表面加工质量(R_a0.8μm,表面无烧伤)的前提下,普通磨料砂轮GC46L10V磨抛加工钛合金的材料去除率和磨抛比分别可达5000mm~3/min和2.5,超硬磨料陶瓷结合剂CBN砂轮磨抛加工钛合金的材料去除率和磨抛比分别可达2000mm~3/min和4。基于研究结果,针对钛合金风扇叶片开展了砂带磨抛加工验证试验,工件加工质量良好。     

TC4-DT钛合金磨削表面特性及其摩擦磨损性能

钛合金是一种典型难磨削加工材料,磨削表面易出现烧伤、裂纹等热损伤。本文开展了TC4-DT钛合金磨削实验,通过扫描电镜（SEM）、能谱（EDS）、X射线衍射（XRD）、显微硬度仪、金相显微镜及球-盘摩擦磨损实验仪研究了其表面特性及摩擦磨损性能。结果表明：低速磨削表面质量好,摩擦磨损性能较基体略提高;当砂轮线速度为80 m/s时,磨削表面质量良好,摩擦系数为0.38,较基体降低40%;而砂轮线速度为100 m/s时,磨削表面出现严重烧伤、网状裂纹。因此选择合理的高速磨削工艺可避免烧伤、裂纹等热损伤缺陷,并可有效改善表面摩擦磨损性能;磨削表面干摩擦磨损机制为磨粒磨损、粘着磨损和剥层磨损。     

航空发动机整体叶盘磁力研磨光整实验

磁力研磨工艺抛光整体叶盘时,工件与磁极干涉严重,用径向磁极代替轴向磁极加工可有效避免干涉,但研磨压力小、研磨效率低.通过对磁力研磨径向磁极加工机理和单个研磨粒子的微观受力情况详细分析得到:提高磁场强度变化率可有效增大磁力研磨效率.经有限元模拟分析发现磁极表面沿轴线方向开矩形槽可使磁场强度变化率提高.对镍基高温合金材质整体叶盘进行磁力研磨实验,并对实验数据分析研究得出:以径向磁极为工具的磁力研磨法可实现对整体叶盘的无干涉加工,磁极开矩形槽后磁力研磨效率可提高31%,叶盘表面粗糙度值由研磨前的1.2μm降至0.18μm,验证了磁力研磨工艺对高效、高质量实现整体叶盘表面光整加工的可行性.      

磨粒磨损对砂带磨削TC17表面完整性的影响研究

砂带磨粒磨损直接影响磨削表面质量进而影响构件综合服役性能.以表面完整性为评估指标,对砂带磨损前后钛合金的表面加工质量进行了试验研究,揭示了砂带磨粒磨损对磨削TC17表面粗糙度、残余应力和表面硬度的影响规律及机制.结果表明,磨粒磨损后由于高度均匀化、单位面积切削磨粒数增加、磨削深度减小,使得表面粗糙度减小、纹理均匀细腻,...     

砂布页轮表面形貌测量与建模

针对整体叶盘抛光磨具砂布页轮,进行磨具表面形貌测量与建模.采用自动变焦三维表面测量仪对P240、P320两种粒度采样砂布页片的表面形貌进行扫描,分析并获得磨粒分布密度、磨粒出刃高度分布等特征参数,继而通过二维数字滤波技术和傅里叶变换法生成具有指定自相关函数的粗糙表面.通过分析砂布页轮柔性特征,分别针对静态及动态砂布页轮...     

Specific grinding energy and surface roughness of nanoparticle jet minimum quantity lubrication in grinding

Nanoparticles with the anti-wear and friction reducing features were applied as cooling lubricant in the grinding fluid. Dry grinding, flood grinding, minimal quantity of lubrication（MQL）, and nanoparticle jet MQL were used in the grinding experiments. The specific grinding energy of dry grinding, flood grinding and MQL were 84, 29.8, 45.5 J/mm³, respectively. The specific grinding energy significantly decreased to 32.7 J/mm³ in nanoparticle MQL. Compared with dry grinding, the surface roughness values of flood grinding, MQL, and nanoparticle jet MQL were significantly reduced with the surface topography profile values reduced by 11%, 2.5%, and 10%,respectively, and the ten point height of microcosmic unflatness values reduced by 1.5%, 0.5%,and 1.3%, respectively. These results verified the satisfactory lubrication effects of nanoparticle MQL. MoS₂, carbon nanotube（CNT）, and ZrO₂ nanoparticles were also added in the grinding fluid of nanoparticle jet MQL to analyze their grinding surface lubrication effects. The specific grinding energy of MoS₂ nanoparticle was only 32.7 J/mm³, which was 8.22% and 10.39% lower than those of the other two nanoparticles. Moreover, the surface roughness of workpiece was also smaller with MoS₂ nanoparticle, which indicated its remarkable lubrication effects. Furthermore,the role of MoS₂ particles in the grinding surface lubrication at different nanoparticle volume concentrations was analyzed. MoS₂ volume concentrations of 1%, 2%, and 3% were used.Experimental results revealed that the specific grinding energy and the workpiece surface roughness initially increased and then decreased as MoS₂ nanoparticle volume concentration increased.Satisfactory grinding surface lubrication effects were obtained with 2% MoS₂ nanoparticle volume concentration.     

碳纤维增强树脂基摩擦材料摩擦磨损性能

为提高树脂基摩擦材料摩擦因数稳定性,改善其抗热衰退性能。以碳纤维作为增强纤维,采用热压成型工艺制备碳纤维增强树脂基摩擦材料;用XD-MSM型定速摩擦试验机测定摩擦磨损性能,研究了不同含量碳纤维增强对树脂基摩擦材料摩擦磨损性能的影响;利用VK-X200三维激光扫描显微镜观察了摩擦材料磨损后表面的微观形貌并探讨其磨损机理。结果表明,碳纤维增强树脂基摩擦材料的硬度、压缩强度和剪切强度均得到提高,并随碳纤维含量的增加而逐渐增大;碳纤维增强作用提高了树脂基摩擦材料的耐磨性和摩擦因数的稳定性,改变了树脂基摩擦材料的摩擦磨损形式;碳纤维含量为4wt%的增强树脂基摩擦材料摩擦因数稳定性较高,抗热衰退性能较好,磨损机制主要为疲劳磨损。     

自由曲面结构磁性抛光去除试验研究

磁性抛光因柔性工具的工件表面适应性高而具有较好的应用潜力。自行设计抛光工具头,制备磁性抛光体,搭建试验平台,并对不锈钢平面工件进行定点抛光试验,平均去除效率为0.231μm/10min,且工件表面质量得到了很大的改善,验证了该磁性抛光方法的可行性。继而对两种自由曲面结构工件进行抛光:一是采用工具头水平移动式、工具头等高线移动式两种不同的抛光进给运动方式对不同曲率的不锈钢工件进行抛光去除试验,试验证明:两种抛光方式对每个曲率的轮廓均有去除能力,去除量在0.14~1.33μm之间;二是对3D打印的光敏树脂微结构自由曲面定点抛光,单位时间去除效率在8.957~12.587μm/10min之间,且改善了轮廓的光滑度。初步试验表明,磁性抛光方法对两种自由曲面结构均有一定的去除能力,可进一步探索磁性抛光技术应用于自由曲面结构确定性抛光。