共查询到20条相似文献,搜索用时 62 毫秒
1.
综合模块化航空电子(IMA)架构具有成本低、高度灵活性和易扩展性等特点,已被越来越多的飞机采用。远程数据接口单元提供接口资源,它是IMA平台的重要设备之一。可配置的远程数据接口单元对降低飞机的成本有着巨大的好处。对比了联合式航空电子和IMA架构,并研究远程数据接口单元的需求;从需求出发,基于DO-297标准定义的IMA特点,提出了远程数据接口单元的设计思路;然后基于当前行业水平和工程经验,提出了三种可行的设计方案。 相似文献
2.
3.
4.
5.
航空电子系统FC交换式网络的可靠性研究 总被引:6,自引:1,他引:6
对于采用光纤通道(FC)互连的航空电子系统,从FC的基本模型出发,给出了由多个FC交换机组成的FC交换式网络的通信模型;采用基于任务的可靠性建模方法,给出了FC交换式网络的可靠性计算公式,并提出了任务基本路径的概念。根据航空电子系统提高可靠性的需要,提出了FC交换式网络的2种冗余拓扑结构:基本路径冗余和全网络冗余;最后通过实例分析了端口单元、交换要素单元和链路单元对FC交换式网络及2种冗余拓扑结构可靠性的影响;FC交换式网络可靠性的研究对于航空电子系统设计阶段的容错设计和拓扑选择都将起到指导作用。 相似文献
6.
航空数字数据传输系统接口设计 总被引:3,自引:1,他引:3
随着机载电子设备向标准化、综合化发展 ,航空数字数据传输系统的设计越来越受关注 ,目前广泛采用ARINC42 9总线作为航空电子系统间信息传输的标准。文章介绍了两种总线接口芯片EF44 42、HS - 32 82 ,以及实现ARINC42 9通信的接口电路 相似文献
7.
8.
9.
航空电子系统已成为保障飞机安全飞行和完成各种作战任务所必需的系统,也是衡量飞机性能的重要因素,航空电子系统在研制中,通常需要建立动态仿真综合设施,为此就要设计其中的软件部分,通过对航空电子系统动态仿真综合设施软件模拟器设计的论述,总结和分析了软件模拟器的设计思路和方法。 相似文献
10.
航空电子系统日益增长的复杂性使其必须走向分布式处理的道路。本文介绍一个基于1553B总线的分布式航空电子系统的实验模型——EPDAS系统,讨论了EPDAS系统信息传输机构的有关组成部分:总线通信协议、通信管理软件和总线接口,本文在分析传统的同步总线控制方式的缺点之后,提出了询问和命令/响应相结合的总线控制方式,该方式能提高总线传输的效率和实时性。在EPDAS系统的总线接口设计中,引入了流水线并行处理技术,解决了总线接口的瓶颈问题,并使之易于VLSI化;伪DMA控制的概念,使总线接口电路更加简化;共享存贮器的互连技术,具有效率高、控制简单、容易实现等优点。EPDAS系统结构合理、效率高,符合国情、适合于新一代的飞机。 相似文献
11.
12.
基于飞机油箱模型形状特征油量测量切片步长选择方法研究 总被引:1,自引:0,他引:1
在分析飞机数字式油量测量过程中目前广泛使用的切片法油量测量原理的基础上,针对现有的定步长切片法无法得到准确、可靠的燃油质量特性数据库的缺陷,结合对飞机油箱模型形状特征的分析,提出了基于飞机油箱模型形状特征的油量测量切片步长选择方法。此方法包括切片步长整体和局部选择两个过程,整体选择以实现相邻两切片平面所夹油箱模型体积近似相等为目的来确定切片步长,以体现油箱模型截面整体变化规律;局部选择以设计切片平面与截面突变平面重合或尽可能接近的方式,突出油箱截面的局部变化特征。实验结果表明:该切片步长选择方法较定步长方法能够建立更为合理、可靠的燃油质量特性数据库,从而提高了油量测量精度。 相似文献
13.
NING Guo-dong ZHANG Shu-guang FANG Zhen-ping 《中国航空学报》2007,20(1):1-8
A method for the implementation of integrated three-degree-of-freedom constrained entry guidance for reusable launch vehicle is presented. Given any feasible entry conditions, terminal area energy management interface conditions, and the reference trajectory generated onboard then, the method can generate a longitudinal guidance profile rapidly, featuring linear quadratic regular method and a proportional-integral-derivative tracking law with time-varying gains, which satisfies all the entry corridor constraints and meets the requirements with high precision. Afterwards, by utilizing special features of crossrange parameter, establishing bank-reversal corridor, and determining bank-reversals according to dynamically adjusted method, the algorithm enables the lateral entry guidance system to fly a wide range of missions and provides reliable and good performance in the presence of significant aerodynamic modeling uncertainty. Fast trajectory guidance profiles and simulations with a reusable launch vehicle model for various missions and aerodynamic uncertain-ties are presented to demonstrate the capacity and reliability of this method. 相似文献
14.
15.
The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow 总被引:1,自引:0,他引:1
This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation. 相似文献
16.
Abnormal Shape Mould Winding 总被引:1,自引:0,他引:1
Fu Hongya Wang Xianfeng Han Zhenyu Fu Yunzhong 《中国航空学报》2007,20(6):552-558
为解决网格化芯模的缠绕问题,本文提出了复合材料面片缠绕机理;接着详细分析了面片缠绕过程中的芯模凹曲面上纤维滑线和架空现象,应用微分几何曲面理论和空间几何理论,提出判据及其解决方案;最后,针对飞机发动机进气道的缠绕成型,编制缠绕控制程序并进行相应的实验,验证了面片缠绕方法的可行性。 相似文献
17.
18.
19.
航天器返回地球的气动特性综述 总被引:4,自引:0,他引:4
航天器返回地球的飞行过程中,气动特性是实现将宇宙飞行速度减到落地前速度、保证再入飞行得到有效控制以及再入防热安全可靠的关键因素。针对简单旋成体气动外形、半弹道式再入控制、烧蚀防热类返回航天器,综述了返回地球过程中变化的空气流域特性、航天器周围的气体绕流环境、空气与航天器作用产生的动力学与热效应等。系统地给出了该类航天器的再入气动特性参数与飞行性能的共性规律,包括:气动阻力与再入减速、气动升力与再入轨迹控制、配平攻角与飞行稳定性、气动加热与防热,以及再入过程中不同气动特性航天器、气象条件变化等对再入飞行性能的影响规律。为航天器开展返回飞行过程的跨流域气动性能工程研制提供设计参考。 相似文献
20.
基于马赫数分布可控曲面外/内锥形基准流场的前体/进气道一体化设计 总被引:4,自引:1,他引:3
提出了一种高超声速飞行器乘波前体的外锥形基准流场设计方法,在锥面马赫数分布规律给定的条件下,通过有旋特征线法实现反设计,提高了基准流场设计的灵活性。该基准流场通过锥形"下凹"弯曲激波和波后等熵压缩波系压缩气流,可以在较短的长度内完成高效压缩。基于反正切马赫数分布外锥形基准流场设计的乘波前体具有较高的容积率,乘波特性良好且出口均匀,设计点时有黏升阻比为1.89。另外,基于该乘波前体和马赫数分布可控的内收缩进气道给出了一种双乘波的前体与进气道一体化设计方案,实现了内外流分别独立乘波,充分发挥了乘波前体和内收缩进气道的各自优势。 相似文献