基于CEEMDAN降噪与双谱分析的滚动轴承故障诊断

滚动轴承早期故障信号中的噪声成分会影响到故障特征的提取。为了提高含噪故障信号中滚动轴承早期故障特征提 取的准确性，将基于自适应噪声的完备经验模态分解（CEEMDAN）用于滚动轴承振动信号的降噪中，并对降噪后的轴承故障信号 进行双谱分析。结果表明：CEEMDAN可有效去除轴承振动信号中的低频噪声干扰，经CEEMDAN降噪后的不同轴承故障信号的 双谱全局图存在明显差异，根据这些差异可在宏观上对不同轴承故障加以区分；通过经CEEMDAN降噪后的不同轴承故障信号的 双谱细节图可以正确提取不同轴承故障的特征频率，从而实现对各轴承故障的有效诊断。CEEMDAN降噪结合双谱分析可为滚 动轴承故障诊断提供一种新的有效方法。     

Total information processor for 121.5/243 MHz SARSAT signals

Search and rescue satellite-aided tracking (SARSAT) has certain shortcomings which could possibly be ameliorated by employing a more extensive signal processing strategy. The approach proposed is based on partially compensating for the Doppler shift, which then permits the data processing windows to be increased significantly. Incorporating a ranking technique with the conventional fast Fourier transform (FFT) processor and implementing an autoregressive moving-average estimator provides an optimal strategy that maximizes the probability of detecting the emergency signals     

GPS软件接收机的捕获与跟踪算法

研究了GPS软件接收机的捕获与跟踪算法。分析了时域串行滑动相关捕获算法和频域基于FFT的并行相关捕获算法,设计了适合GPS软件接收机的并行算法,实现了对空中可见卫星的捕获。针对GPS信号的特点,设计了基于DLL与PLL相结合方法的GPS跟踪算法。利用实测中频信号对上述捕获与跟踪算法进行了验证分析,测试结果表明,基于FFT的并行相关捕获算法能够有效增强软件接收机的捕获能力,采用DLL与PLL相结合的方法能够实现对GPS信号的有效跟踪。     

航空发动机转子不平衡量突增的自动识别

为实现在航空发动机振动信号分析时因封严胶条脱落发生的转子不平衡量突增的自动识别,采用多傅里叶变换（FFT）滤波技术获得转速跟踪滤波后的基频振动时域信号,提出了振幅突增和突增后振幅稳定的转子不平衡量突增的2种特征,通过应用案例对振动信号的程序化进行处理,得到转速跟踪滤波后的基频振动时域信号及转子不平衡量突增的识别参数,数据结果中振幅增大比例系数达到3.75,且突增后振幅稳定。结果表明：采用FFT滤波技术,实现了转子不平衡突增的自动识别,并验证了识别方法的有效性。转子不平衡量突增的识别技术应用于在线监测系统时,能及时识别故障并发出报警信息,保证设备运转的安全;应用于离线振动信号分析系统时,缩短了人工数据分析时间,提高了工作效率。     

航空发动机喘振引起转子系统横向载荷的确定方法

对喘振引起的转子系统的横向载荷进行了研究,对发动机喘振过程中的压力脉动信号进行FFT分析和相关分析,识别出旋转失速时失速团的旋转速度,推断出整个截面的压力分布,进而得到了喘振对转子的横向作用力。     

发动机起动过程的振动谱分析

在开展某型涡桨发动机振动监控课题研究工作时,曾迂到该型发动机在台架试车过程中出现压气机转子前部叶片严重偏磨和轴承损坏等故障,且每次都发生在起动过程,故障后均伴有严重的振动损坏现象。为此,我们决定从测量分析发动机起动过程的振动特性着手,寻找规律,为排故提供重要依据。因其问题属于瞬态振动分析,以运用实时振动分析技术进行数据处理为宜。      

High-Resolution Frequency Measurement by Linear Prediction

The efficacy of linear prediction spectrum analysis (LPSA) (also called autoregressive or maximum entrophy spectrum analysis) for problems concerning narrowband signals in noise is examined by means of Monte Carlo simulation. For the case of pure tones (sinusoids) in white noise, both frequency estimation accuracy and resolution of two closely spaced tones with the linear prediction approach are discussed. In addition, estimation of the carrier frequency of a narrowband random (fading) Gaussian signal in noise is considered. The results are compared with standard fast Fourier transform (FFT) methods. These comparisons indicate that there is no significant advantage to using the linear prediction approach with real (bandpass) data. It is concluded that these experiments should be repeated with complex (baseband) data before a complete assessment of the LPS approach can be made.     

Radar target identification using the bispectrum: a comparativestudy

Radar target identification is performed using time-domain bispectral features. The classification performance is compared with the performance of other classifiers that use either the impulse response or frequency domain response of the unknown target. The classification algorithms developed here are based on the spectral or the bispectral energy of the received backscatter signal. Classification results are obtained using simulated radar returns derived from measured scattering data from real radar targets. The performance of classifiers in the presence of additive Gaussian (colored or white), exponential noise, and Weibull noise are considered, along with cases where the azimuth position of the target is unknown. Finally, the effect on classification performance of responses horn extraneous point scatterers is investigated     

航空发动机转子碰磨故障状态识别

基于谐振动在弹性介质传递过程中能量波动的特点, 提出一种以能量分布与传递为出发点的转子碰磨状态识别方法.该方法以快速傅立叶变换法处理测振信号, 以能量的观点理解振动色谱图, 并结合时域图、频谱图和瀑布图对转子是否存在碰磨做出判断.经试验验证, 该方法简便可行, 为工程应用提供了实践依据.      

基于广义S变换的图像局部时频分析

 非平稳信号具有良好的时频局部特性,但是使用一些常规的信号处理方法对其进行时频分析具有一定难度。为了解决这一难题,引入基于广义S变换的时频分析方法来进行一维和二维空间非平稳信号的时频分析。同时,为避开对图像直接进行S变换带来的大时间开销和运算难度,选用不同尺度的局部窗口将二维图像转化成一维信号进行处理,再分别利用基本S变换和时频分辨率可调的广义S变换进行算法仿真和时频分析。试验结果表明,广义S变换比基本S变换具有更灵活的时频聚焦性。     

基于概率统计的DS/FH系统干扰检测算法

基于时频分布的干扰检测算法是DS/FH（Direct Sequence/Frequency Hopping,直接序列扩频/跳频扩频）系统干扰检测的传统手段,针对其运算量大、实时性差,以及无法检测某些特殊干扰信号等问题,提出一种基于概率统计的干扰检测算法.通过统计DS/FH系统频谱图中各频率的幅值出现位置,以DS/FH信号与干扰信号频谱分布规律的差别为判决依据,完成DS/FH系统中干扰信号的检测.分析和仿真结果表明：该检测算法能够有效识别DS/FH系统中的典型干扰信号,与传统基于时频分布的检测算法相比,能够实现某些特殊干扰信号的有效检测;同时,由于该算法不需要进行复杂的时频联合分析,其运算复杂度大大降低,能够实现DS/FH系统干扰信号的快速检测.     

飞机AMU自动测试系统测试信号失真度检测研究

针对飞机AMU自动测试系统中对音频信号失真度测量的要求，运用PC机和数据采集卡，采用加窗FFT、把整个主瓣的宽度作为基波值来计算基波分量有效值的算法实现了在计算机中对音频信号失真度的直接测量。实验验证，该方法可对组件维护手册（CMM）中所有频率的测试信号进行精确的失真度计算，具有频率范围广、精度高、简便易行等特点。     

Efficient wideband signal parameter estimation using a radon-ambiguity transform slice

A novel efficient technique based on a single slice Radon-ambiguity transform (RAT) for time-delay and time-scale estimation is proposed. The proposed approach combines the narrowband cross-ambiguity function (NBCAF), the wideband cross-ambiguity function (WBCAF), and a single slice RAT to estimate multiple target parameters in noisy environments. The square modulus of Gaussian-enveloped linear frequency modulated (GLFM) signals has high-energy centrality in the ambiguity plane. Its peaks in the NBCAF fall along nearly straight lines whose slopes depend on the Doppler rates of the moving targets. These lines could be effectively detected by computing the entire Radon transform of the NBCAF for all possible angles; however, it is a computationally intensive procedure. It is shown that without calculating the entire RAT, it is possible to estimate target parameters using only a single slice of the RAT, i.e., using an appropriate projection of the NBCAF. It is demonstrated that the proposed method can successfully separate overlapping targets efficiently. The efficiency is achieved due to fast Fourier transform (FFT)-bascd processing, use of a single slice of RAT, and the use of only one-dimensional (1-D) searches.     

Quantitative SNR analysis for ISAR imaging using jointtime-frequency analysis-Short time Fourier transform

V.C. Chen recently presented an inverse synthetic aperture radar (ISAR) imaging technique using the joint time-frequency analysis (JTFA), which has been shown having a better performance for maneuvering targets over the conventional Fourier transform method. The main reason is because the frequencies of the radar returns of the maneuvering targets are time varying and a JTFA is a technique that is suitable for such signals, in particular a JTFA may concentrate a wideband signal, such as a chirp, while it spreads noise. We quantitatively study the signal-to-noise ratio (SNR) in the ISAR imaging using one of the typical JTFA techniques, namely the short time Fourier transform (STFT). We show that the SNR increases in the joint time-frequency (TF) domain over the one in the time or the frequency domain alone both theoretically and numerically. This quantitatively shows the advantage of the JTFA technique for the ISAR imaging     

基于时频脊线和阶次分析的转子故障诊断

为解决采用在转子升降速过程中产生的非平稳信号难以进行故障诊断的问题,提出一种基于2维时频脊线和阶次分析的转子故障诊断方法。采集转子升降速信号,采用2维时频分布的峰值脊线提取法获得信号脊线特征,结合脊线特征与等角度重采样技术依次获得信号角度域、角-阶域和阶次域图像,将信号阶次域内的特征参数作为故障敏感特征,输入人工神经网络诊断模型,对转子信号的故障类型进行分类。利用实测信号验证所提方法的实际应用效果,并与传统特征提取法的结果进行对比。结果表明:阶次分析方法的测试准确率约为99.8%,标准差小于0.09%,均优于传统特征提取法。基于时频脊线和阶次分析的转子故障诊断方法具有更高的诊断准确率,在非平稳信号特征提取过程中具有很好的可行性和准确性。     

Super resolution SAR imaging via parametric spectral estimationmethods

Super resolution synthetic aperture radar (SAR) image formation via sophisticated parametric spectral estimation algorithms is considered. Parametric spectral estimation methods are devised based on parametric data models and are used to estimate the model parameters. Since SAR images rather than model parameters are often used in SAR applications, we use the parameter estimates obtained with the parametric methods to simulate data matrices of large dimensions and then use the fast Fourier transform (FFT) methods on them to generate SAR images with super resolution. Experimental examples using the MSTAR and Environmental Research Institute of Michigan (ERIM) data illustrate that robust spectral estimation algorithms can generate SAR images of higher resolution than the conventional FFT methods and enhance the dominant target features     

Application of successive interference cancellation to the GPS pseudolite near-far problem

Ground-based transmitters called pseudolites have been proposed to augment the basic Global Positioning System (GPS) in environments where satellite visibility is limited. One difficulty in their use is the so-called near-far problem, where in close proximity to the ground transmitter, the pseudolite signal can be orders of magnitude stronger than the satellite signals. This large range of signal levels prevents a conventional receiver from simultaneously detecting both types of signals. This paper describes the application of a signal processing technique, known as successive interference cancellation (SIC), to the acquisition and tracking of weak satellite signals in the presence of a nearby pseudolite and possible multipath reflections of this pseudolite signal. The SIC architecture is implemented on simulated and experimental near-far data sets. The results are compared with a conventional detector and improvements in acquisition and tracking performance are illustrated.     

Gating Functions for Multipath Mitigation in GNSS BOC Signals

A new multipath mitigation technique is proposed for binary offset carrier (BOC) signals in global navigation satellite systems (GNSS) using the concept of gating function originally conceived for the GPS coarse-acquisition (C/A) code. Specially-tailored pulses are utilized to diminish the number of false-lock points of the code discriminator response and to improve the multipath mitigation capability. The code loop includes only four real correlators (two extra correlators are required for the simplified bump-jumping algorithm with BOC(n,n) signals). Results obtained with BOC(n,n) and BOC(2n,n) signals show that this technique eliminates the multipath ranging errors for reflected rays with relative delays typically above twenty percent of the spreading code chip duration, thus comparing favorably with the conventional receiver correlation techniques.     

基于独立分量分析的航空发动机振动信号盲源分离

阐述了基于峭度的盲源分离开关算法,对仿真信号进行分离,验证了该算法的可行性.并将该算法与FFT分离法结合,对某型双转子航空发动机高、低压转子实测振动信号进行了盲源分离实践,取得了很好的分离效果,从而为双转子发动机振动监测与故障诊断提供了一种可行的信号处理方法.