基于反作用发动机推力的空天飞行器再入姿态飞行控制

研究了空天飞行器(ASV)再入跨大气层飞行时的姿态控制问题。在ASV跨大气层再入飞行时,通过反作用控制系统(RCS)中的反作用发动机推力产生控制力矩来控制ASV的姿态,以补偿气动舵面操纵失效或者部分失效而引起的控制力矩不足;随着空气密度的增加,气动舵面逐步介入控制系统,RCS随之逐步退出.由于快回路控制器产生进行姿态控制所需要的控制力矩,其通过相应的控制分配将控制力矩映射到作动器,为了减轻作动器的抖振,提出了利用基于区域模型的T-S模糊多模型控制方法设计快回路控制器,在跟踪期望角速度的同时,柔化控制信号.最后通过仿真验证了所提方法的有效性.      

喷嘴为执行机构的空间飞行器基于误差四元数的非线性姿态跟踪控制

研究带喷嘴空间飞行器在姿态跟踪机动时的多轴耦合非线性姿态控制问题。姿态运动学和动力学用误差四元数描述。通过线性变换将误差四元数动力学方程转换成 4个摄动双积分系统 ,并基于此摄动双积分系统设计了开关控制器。由误差四元数及其导数构成的抛物型开关函数决定了控制器中的逻辑。文章考虑了最短的姿态捕获路径、外部干扰抑制、和不确定参数补偿问题。控制器允许力矩矩阵为非对称 ,从而使喷气执行机构的安装有更好的灵活性。由于不需要目标的加速度反馈 ,控制器可用于对机动目标的跟踪。用相平面方法分析了闭环系统的鲁棒稳定性。仿真结果验证了控制方案的可行性     

Adaptive Integral-type Sliding Mode Control for Spacecraft Attitude Maneuvering Under Actuator Stuck Failures

A fault tolerant control (FTC) design technique against actuator stuck faults is investigated using integral-type sliding mode control (ISMC) with application to spacecraft attitude maneuvering control system. The principle of the proposed FTC scheme is to design an integral-type sliding mode attitude controller using on-line parameter adaptive updating law to compensate for the effects of stuck actuators. This adaptive law also provides both the estimates of the system parameters and external disturbances such that a prior knowledge of the spacecraft inertia or boundedness of disturbances is not required. Moreover, by including the integral feedback term, the designed controller can not only tolerate actuator stuck faults, but also compensate the disturbances with constant components. For the synthesis of controller, the fault time, patterns and values are unknown in advance, as motivated from a practical spacecraft control application. Complete stability and performance analysis are presented and illustrative simulation results of application to a spacecraft show that high precise attitude control with zero steady-error is successfully achieved using various scenarios of stuck failures in actuators.     

Variable structure control and active vibration suppression of flexible spacecraft during attitude maneuver

This paper presents a new approach to vibration reduction of flexible spacecraft during attitude maneuver by using the theory of variable structure control (VSC) to design switching logic for thruster firing and lead zirconate titanate (PZT) as sensor and actuator for active vibration suppression. The spacecraft to be investigated is a hub with a cantilever flexible beam appendage, which can undergo a single axis rotation. The proposed control system includes the attitude controller acting on the rigid hub, designed by variable structure control technique, and the surface-bonded PZT patches for active vibration suppression of flexible appendages, designed by the positive position feedback (PPF) control technique. To avoid chattering, pulse-width pulse-frequency (PWPF) modulation is adopted for the thruster control, which makes the thrusters to be operated in a close to linear manner and also can suppress the relatively large amplitude vibrations excited by, for example, rapid maneuver. However, some residual micro-vibrations still exist due to the switching actions. Upon that, the technique of active vibration control using PZT is turned on to provide further vibration suppression of the residual micro-vibrations and fine tuning of the system performance. By combining the advantages of both these control strategies, an improved performance for vibration control in both the macro-and micro-senses can result. Both analytical and numerical results are presented to show the theoretical and practical merit of this approach.     

基于新型终端滑模的航天器执行器故障容错姿态控制

针对受干扰的刚体航天器冗余执行器存在故障与控制受限的姿态跟踪控制问题,提出一类基于新型指数形式的非奇异快速滑模面（ENFTSM）与趋近律的姿态容错控制器设计方法。当部分推力器发生故障时,假设剩余推力器具有输出饱和特性且能提供足够推力保证航天器执行任务,相比一般终端滑模控制器,本文设计的控制器不仅能使系统状态以更快的速度到达平衡点,且不需要在线对执行器故障信息进行检测和分离。基于Lyapunov方法证明本文设计的控制器能保证闭环系统稳定,且能有效地抑制外部干扰、控制受限和执行器故障等约束。最后对提出的控制算法进行了数值仿真,其结果表明了该控制器的有效性。     

基于新型终端滑模的航天器执行器故障容错姿态控制简

 针对受干扰的刚体航天器冗余执行器存在故障与控制受限的姿态跟踪控制问题,提出一类基于新型指数形式的非奇异快速滑模面（ENFTSM）与趋近律的姿态容错控制器设计方法。当部分推力器发生故障时,假设剩余推力器具有输出饱和特性且能提供足够推力保证航天器执行任务,相比一般终端滑模控制器,本文设计的控制器不仅能使系统状态以更快的速度到达平衡点,且不需要在线对执行器故障信息进行检测和分离。基于Lyapunov方法证明本文设计的控制器能保证闭环系统稳定,且能有效地抑制外部干扰、控制受限和执行器故障等约束。最后对提出的控制算法进行了数值仿真,其结果表明了该控制器的有效性。     

敏捷卫星的联合执行机构控制策略

 针对对地观测敏捷卫星大角度快速机动、高控制精度的任务需求,提出了联合推力器与飞轮作为执行机构的控制策略。该控制策略综合利用2种执行机构的优点:推力器以前馈的形式提供机动过程中所需的主要力矩以实现航天器大角度的快速机动,而飞轮以反馈的形式提供精准的控制力矩以提高机动过程中的姿态控制精度。为补偿由于初始状态偏差和推力器输出力矩不准确所带来的控制误差,采用变结构控制设计了2种姿态跟踪控制器,使航天器能够渐进地跟踪上参考轨迹。并对姿态机动控制过程中,飞轮力矩及转速可能出现的饱和问题作了相应的修正。仿真结果表明了所提控制策略及所设计控制算法的可行性和有效性。     

Finite-time sliding mode attitude control for a reentry vehicle with blended aerodynamic surfaces and a reaction control system

This paper proposes a finite-time robust flight controller, targeting for a reentry vehicle with blended aerodynamic surfaces and a reaction control system(RCS). Firstly, a novel finite-time attitude controller is pointed out with the introduction of a nonsingular finite-time sliding mode manifold. The attitude tracking errors are mathematically proved to converge to zero within finite time which can be estimated. In order to improve the performance, a second-order finite-time sliding mode controller is further developed to effectively alleviate chattering without any deterioration of robustness and accuracy. Moreover, an optimization control allocation algorithm, using linear programming and a pulse-width pulse-frequency(PWPF) modulator, is designed to allocate torque commands for all the aerodynamic surface deflections and on–off switching-states of RCS thrusters.Simulations are provided for the reentry vehicle considering uncertain parameters and external disturbances for practical purposes, and the results demonstrate the effectiveness and robustness of the attitude control system.     

共位衍射电磁航天器成像过程中的小推力控制 (新型推进系统控制专栏)

为了满足衍射成像系统在解决低轨遥感航天器覆盖范围小、目标重访周期长等问题的同时,而引入的航天器相对位置、姿态控制需求。针对共位衍射航天器相对位置、姿态控制过程中传统推力器带来的羽流污染问题,本文采用电磁推力器和飞轮作为执行器,设计一种基于快速非奇异滑模的轨道控制器和基于PID的姿态控制器。所设计的快速非奇异滑模轨道控制器为共位衍射航天器频繁位置调整提供控制保障,基于PID的姿态控制器能够消除由电磁力耦合产生的电磁干扰力矩。研究结果表明：基于相对轨道动力学方程设计的快速非奇异滑模控制律鲁棒性好、收敛速度快,能够达到两颗共位衍射电磁航天器沿z轴保持在10m相对距离的控制效果。在轨道调整过程中,其姿态能够通过PID算法稳定控制到期望姿态,使衍射成像结构一直保持不变,从而有效完成衍射成像任务。     

Fuel Savings in the WHECON Attitude Control System Using an Asymmetric Controller

This paper investigates the possibility of generating an on-off limit cycle mode in the WHECON attitude control system. lt is shown that, by eliminating the off set angle ? in the roll-actuated control torquer, the WHECON system can be reduced to the structure considered earlier by Mendel and, therefore, an on-off limit cycle can be generated simply by introducing an appropriate amount of asymmetry into the deadzone characteristic of the WHECON controller. Because with this mode of on-off limit cycle the thruster jets will fire only once in each cycle of the oscillation, it is claimed that a considerable amount of fuel can be saved by the proposed modifications to the original WHECON design. Dynamic simulation study was conducted with the actual nonlinear model of the WHECON system considered and the results indicate that, for both zero and nonzero values of the off set angle ?, substantial fuel savings can be achieved by using the asymmetric controller.     

Output stabilization of flexible spacecraft with active vibration suppression

Addressed here is the problem of designing a dynamic controller capable of performing rest-to-rest maneuvers for flexible spacecraft, by using attitude measures. This controller does not need the knowledge of modal variables and spacecraft angular velocity. The absence of measurements of these variables is compensated by appropriate dynamics of the controller, which supplies their estimates. The Lyapunov technique is applied in the design of this dynamic controller. Possible source of instability of the controlled system in real cases are the influence of the flexibility on the rigid motion, the presence of disturbances acting on the structure, and parameter variations. In order to attenuate their effects and to damp out undesirable vibrations affecting the spacecraft attitude, distributed piezoelectric actuators are used. In fact, in presence of disturbances and/or parameter variation the proposed controller ensures an approximate solution of the control problem.     

Accelerated Landweber iteration based control allocation for fault tolerant control of reusable launch vehicle

This paper presents a novel Fault Tolerant Control(FTC) scheme based on accelerated Landweber iteration and redistribution mechanism for a horizontal takeoff horizontal landing reusable launch vehicle(RLV). First, an adaptive law based on fixed-time non-singular fast terminal sliding mode control(NFTSMC), which focuses on the attitude tracking controller design for RLV in the presence of model couplings, parameter uncertainties and external disturbances, is proposed to produce virtual control co...     

考虑执行机构误差的编队卫星姿态分布式时延滑模自适应协同控制

针对编队卫星姿态协同控制问题,在考虑到执行机构误差的前提下,提出一种将时延控制与滑模自适应控制相结合的鲁棒控制方法.该方法通过引入自适应更新律实现对执行机构小角度安装误差的在线估计,同时通过滑模控制完成对外界干扰和执行机构随机幅值误差等随机扰动的抑制.由于引入了时延环节,只需对上一时刻控制力矩进行单位时延,达到大大简化...     

Attitude Control Considering Variable Input Saturation Limit for a Spacecraft Equipped with Flywheels

A new attitude controller is proposed for spacecraft whose actuator has variable input saturation limit. There are three identical flywheels orthogonally mounted on board. Each rotor is driven by a brushless DC motor (BLDCM). Models of spacecraft attitude dynamics and flywheel rotor driving motor electromechanics are discussed in detail. The controller design is similar to saturation limit linear assignment. An auxiliary parameter and a boundary coefficient are imported into the controller to guarantee system stability and improve control performance. A time-varying and state-dependent flywheel output torque saturation limit model is established. Stability of the closed-loop control system and asymptotic convergence of system states are proved via Lyapunov methods and LaSalle invariance principle. Boundedness of the auxiliary parameter ensures that the control objective can be achieved, while the boundary parameter’s value makes a balance between system control performance and flywheel utilization efficiency. Compared with existing controllers, the newly developed controller with variable torque saturation limit can bring smoother control and faster system response. Numerical simulations validate the effectiveness of the controller.     

Soft landing stability analysis of a Mars lander under uncertain terrain

Safe soft landing of the lander is vital to the Mars surface exploration mission. Analysis and verification of the landing stability under uncertain terrain play an important role in lander design. However, the effect of uncertain terrain is ignored in most existing studies, making the analysis incomprehensive and increasing the risk of landing failure in practice. In this paper, a Mars lander with 10 attitude control thrusters is introduced and its dynamics model is then established considering plastic deformation parts and nonlinear contact forces. The effectiveness and accuracy of the dynamics modeling method are verified by experiments with an average relative error of 10%. In order to carry out the dynamics simulation with high-fidelity terrain, a terrain generation method based on statistical data is proposed. Through Monte Carlo simulation under a 50 m × 50 m randomly generated landing terrain, the stability of the lander and the effects of attitude control thrusters are analyzed. The results show that the failure rate is 5.5%, in which the primary failure forms are overturning and abnormal attitude. When the landing simulations are repeated without thrusters, the stable ratio decreases from 94.5% to 90.7%, suggesting the positive effects of attitude control thrusters in improving landing stability under rough terrain.     

Closed-loop dynamic control allocation for aircraft with multiple actuators

A closed-loop control allocation method is proposed for a class of aircraft with multiple actuators. Nonlinear dynamic inversion is used to design the baseline attitude controller and derive the desired moment increment. And a feedback loop for the moment increment produced by the deflections of actuators is added to the angular rate loop, then the error between the desired and actual moment increment is the input of the dynamic control allocation. Subsequently, the stability of the closed-loop dynamic control allocation system is analyzed in detail. Especially, the closedloop system stability is also analyzed in the presence of two types of actuator failures: loss of effectiveness and lock-in-place actuator failures, where a fault detection subsystem to identify the actuator failures is absent. Finally, the proposed method is applied to a canard rotor/wing (CRW) aircraft model in fixed-wing mode, which has multiple actuators for flight control. The nonlinear simulation demonstrates that this method can guarantee the stability and tracking performance whether the actuators are healthy or fail.     

Practical stabilization in attitude thruster control

The attitude stabilization of a spacecraft using thrusters is considered from a practical point of view, i.e., when actuator constraints, uncertainties and failures, measurement noise, fuel consumption, and inertia matrix uncertainty are considered. A variable structure controller based on sliding modes is obtained first, which guarantees global exponential stability under actuator constraints, uncertainties, and failures. The design is based on a continuous average-proportional torque selection function and a set of feasible sliding surfaces, which may be adapted to improve performance. Exponential convergence towards ultimate bounds is guaranteed when all other practical issues arise.     

Global magnetic attitude control of spacecraft in the presence of gravity gradient

The problem of Earth-pointing attitude control for a spacecraft with magnetic actuators is addressed and a novel approach to the problem is proposed, which guarantees almost global closed loop stability of the desired relative attitude equilibrium for the spacecraft. Precisely, a proportional derivative (PD)-like state feedback control law is employed together with a suitable adaptation mechanism for the controller gain. Simulation results are presented, which illustrate the performance of the proposed control law     

Near minimum-time feedback attitude control with multiple saturation constraints for agile satellites

Agile satellites are of importance in modern aerospace applications,but high mobility of the satellites may cause them vulnerable to saturation during attitude maneuvers due to limited rating of actuators.This paper proposes a near minimum-time feedback control law for the agile satellite attitude control system.The feedback controller is formed by specially designed cascaded sub-units.The rapid dynamic response of the modified Bang–Bang control logic achieves the near optimal property and ensures the non-saturation properties on three-axis.To improve the dynamic performance,a model reference control strategy is proposed,in which the on-line near optimal attitude maneuver path is generated by the cascade controller and is then tracked by a nonlinear back-stepping controller.Furthermore,the accuracy and the robustness of the control system are achieved by momentum-based on-line inertial identification.The rapid attitude maneuvering can be applied for tasks including the move to move case.Numerical simulations are conducted to verify the effectiveness of the proposed control strategy in terms of the saturation-free property and rapidness.     

Space Interferometry Mission spacecraft pointing error budgets

Preliminary error budgets for the pointing knowledge, control, and stability of the Space Interferometry Mission (SIM) spacecraft are constructed using the specifications of commercial off-the-shelf attitude determination sensors, attitude control actuators, and other spacecraft capabilities that have been demonstrated in past missions. Results obtained indicate that we can meet all the presently known spacecraft pointing requirements. A large number of derived requirements are generated from this study. Examples are specifications on attitude determination sensors, attitude control actuators, minimum settling time after a rest-to-rest spacecraft slew. Preliminary error budgets constructed in this study must be updated to reflect the changing spacecraft design and requirements