Prospects of using a permanent magnetic end effector to despin and detumble an uncooperative target

Space debris, such as defunct satellites and upper stages of rockets, becomes an uncooperative target after losing its attitude control and communication ability. In addition, tumbling motion can occur due to environmental perturbations and residual angular momentum prior to the object’s end-of-mission. To minimize the collision risk during docking and capturing of the tumbling target, a non-contact method based on the eddy current effect is put forward to transmit the control torque to the tumbling target. The main idea is to induce a controllable torque on the conducting surface of the tumbling target using a rotational magnetic field generated by a Halbach rotor. The radial and axial Halbach rotors are used to damp the spinning and nutation motions of the target, respectively. The normal and tangential force are evaluated concerning the relative pose between the chaser and the target. A simplified dynamic model of the nutation damping and despinning processes is developed and the influences of the asymmetrical principal moments of inertia and transverse angular velocity are discussed. The numerical simulation results show that the designed Halbach rotor stabilized the target attitude within an acceptable time. The electromagnetic nutation damping and despinning method provides new solutions for the development of on-orbit capture technology.     

A deorbiter CubeSat for active orbital debris removal

This paper introduces a mission concept for active removal of orbital debris based on the utilization of the CubeSat form factor. The CubeSat is deployed from a carrier spacecraft, known as a mothership, and is equipped with orbital and attitude control actuators to attach to the target debris, stabilize its attitude, and subsequently move the debris to a lower orbit where atmospheric drag is high enough for the bodies to burn up. The mass and orbit altitude of debris objects that are within the realms of the CubeSat’s propulsion capabilities are identified. The attitude control schemes for the detumbling and deorbiting phases of the mission are specified. The objective of the deorbiting maneuver is to decrease the semi-major axis of the debris orbit, at the fastest rate, from its initial value to a final value of about 6471?km (i.e., 100?km above Earth considering a circular orbit) via a continuous low-thrust orbital transfer. Two case studies are investigated to verify the performance of the deorbiter CubeSat during the detumbling and deorbiting phases of the mission. The baseline target debris used in the study are the decommissioned KOMPSAT-1 satellite and the Pegasus rocket body. The results show that the deorbiting times for the target debris are reduced significantly, from several decades to one or two years.     

Dynamics and control for contactless interaction between spacecraft and tumbling debris

Tumbling debris has become a great threat to orbit activities. Contactless interaction is a novel concept for active debris removal, through which the tumbling debris no longer rotates freely but is under control. The contactless interaction method aims to de-tumble the debris and then maintain desired relative states between the spacecraft and debris. The spacecraft is simultaneously stabilized through three-axis attitude control, which makes the de-tumbling and capture operation much safer, more effective and accurate. The dynamics and control for the contactless interaction have been little studied in the past years. This paper considers a generic dynamics and control problem for contactless interaction between a spacecraft and debris. A translational and rotational dynamics model of contactless interaction is proposed and the 6-DOF equations are established. The contactless interaction control law is designed with the backstepping method, and the spacecraft three-axis control law is designed with the PD control. Simulation results show that the angular momentum is transferred from the debris to the spacecraft and the debris is thus de-tumbled. The desired relative states are achieved efficiently. Significantly, the spacecraft and debris no longer rotate in the inertial frame and, hence, the safety and accuracy for capture operation are guaranteed.     

CubeSats detumbling using only embedded asymmetric magnetorquers

After deployment from a rocket, a CubeSat is detumbled using magnetorquer rods bringing the norm to the point where the reaction wheels take over to reduce the angular velocity to null. Therefore, utilizing reaction wheels for satellite detumbling at higher initial velocities is vital but they are heavy and occupy significant space on a spacecraft having challenging control. To address this challenge, this paper features a disruptive approach that conducts the control only by the PCB-integrated magnetorquers with various geometries using a diverse non-unity track width ratio. The trace widths are parametrized such that the optimal torque to power dissipation ratio is investigated. The optimizations are then simulated for various geometric distributions and validated through comprehensive measurement setups that establish a framework for selecting the best-case coil configuration according to mission requirements. The detumbling rates of multiple asymmetric coil configurations are compared with the embedded designs in published literature and state of the art. It is found that the proposed asymmetric embedded magnetorquers can detumble the vehicle at high initial angular velocities. Lastly, the simulation results of thermal analysis are validated for selecting the application-specific optimal coils configuration. At the end, the proposed system is compared with the embedded magnetorquers available in the literature and commercial attitude control systems.     

Prospects of de-tumbling large space debris using a two-satellite electromagnetic formation

Capturing large space debris with complex rotational motion is extremely challenging. A de-tumbling phase before capturing may be necessary to reduce the risk of collision with debris. This paper proposes a new noncontact de-tumbling method using a two-satellite electromagnetic formation, in which two small electromagnetic satellites, each having a high-temperature superconducting coil, generate control torques to reduce the rotation rate of debris prior to making any physical contact. The electromagnetic interaction of the target-satellite system is analyzed. A relative translational dynamics of the target–satellite system and the attitude dynamics of the target are established. Simulation results show that the proposed method effectively eliminates the rotational motion of the target. It can be safely concluded that the noncontact method for de-tumbling space debris using a two-satellite electromagnetic formation is feasible and potentially applicable to on-orbit capture.     

Deorbiter CubeSat mission design

This paper presents the mission design for a CubeSat-based active debris removal approach intended for transferring sizable debris objects from low-Earth orbit to a deorbit altitude of 100 km. The mission consists of a mothership spacecraft that carries and deploys several debris-removing nanosatellites, called Deorbiter CubeSats. Each Deorbiter is designed based on the utilization of an eight-unit CubeSat form factor and commercially-available components with significant flight heritage. The mothership spacecraft delivers Deorbiter CubeSats to the vicinity of a predetermined target debris, through performing a long-range rendezvous maneuver. Through a formation flying maneuver, the mothership then performs in-situ measurements of debris shape and orbital state. Upon release from the mothership, each Deorbiter CubeSat proceeds to performing a rendezvous and attachment maneuver with a debris object. Once attached to the debris, the CubeSat performs a detumbling maneuver, by which the residual angular momentum of the CubeSat-debris system is dumped using Deorbiter’s onboard reaction wheels. After stabilizing the attitude motion of the combined Deorbiter-debris system, the CubeSat proceeds to performing a deorbiting maneuver, i.e., reducing system’s altitude so much so that the bodies disintegrate and burn up due to atmospheric drag, typically at around 100 km above the Earth surface. The attitude and orbital maneuvers that are planned for the mission are described, both for the mothership and Deorbiter CubeSat. The performance of each spacecraft during their operations is investigated, using the actual performance specifications of the onboard components. The viability of the proposed debris removal approach is discussed in light of the results.     

弹丸撞击防护屏形成碎片云速度特性研究

微流星及空间碎片的高速撞击威胁着长寿命，大尺寸航天器的安全运行，导致其严重的损伤和灾难性的失效，为精确估计微流星及空间碎片主速撞击防护屏产生的碎片对舱壁的损伤，必须确定碎片云速度特性。文章在冲量和能量守恒的基础上，建立了碎片速度性分析模型，研究了碎片云的速度特性，得到了碎片云材料传播及碎片云喷射角随弹丸撞击速度的变化规律。     

自由漂浮机械臂抓取翻滚目标的自适应控制策略

提出了一种自由漂浮机械臂抓取翻滚目标的自适应控制策略.抓取翻滚目标要求自由漂浮机械臂具有很强的轨迹跟踪能力,但是自由漂浮机械臂本身以及目标所存在的运动学和动力学参数不确定性使基于模型的控制器性能急剧下降,甚至变得不稳定.通过对参数的自适应逐步改善基于模型的控制器的性能,并且提出了一种新的自由漂浮机械臂关节空间自适应控制器.最后通过数值仿真对所提出的自适应控制策略进行了验证.     

带偏置点的绳系拖拽离轨系统动力学研究

考虑空间拖船利用飞网/飞爪对空间残骸捕获结束后绳系拖拽系统的动力学特性,开展了基于简化的带偏置点构型的建模及仿真研究.首先,捕获后的组合体包括空间拖船、系绳和空间残骸,系绳在空间残骸一端的牵挂点看作偏置点,给出相应的的绳系拖拽系统构型;其次,以降轨离轨过程为例,建立系统能量方程,并根据欧拉-拉格朗日方程给出系统的动力学表达式并估算系绳张紧情况下的平衡点;最后,设定离轨推力,在不同的初始角速度、系绳张紧或松弛以及不同松弛程度条件下,分析绳系拖拽离轨系统的动力学行为.研究表明,空间残骸小的初始角速度和张紧或略微松弛的系绳能够保证安全离轨.     

旋转非合作目标终端逼近的姿轨控制研究

针对旋转非合作目标的终端逼近过程进行研究, 建立了适用于任意偏心率的精 确航天器相对运动和姿态动力学模型, 并对传统的直线型同步自旋逼近策略进行 改进, 设计了用于保障终端逼近安全性的指数衰减型参考轨迹; 推导了基于比例 微分加解耦控制方法的相对轨道和姿态控制律, 通过数值仿真验证了控制器的有效性.      

Analysis of the orbit lifetime of CubeSats in low Earth orbits including periodic variation in drag due to attitude motion

It is estimated that more than 22,300 human-made objects are in orbit around the Earth, with a total mass above 8,400,000 kg. Around 89% of these objects are non-operational and without control, which makes them to be considered orbital debris. These numbers consider only objects with dimensions larger than 10 cm. Besides those numbers, there are also about 2000 operational satellites in orbit nowadays. The space debris represents a hazard to operational satellites and to the space operations. A major concern is that this number is growing, due to new launches and particles generated by collisions. Another important point is that the development of CubeSats has increased exponentially in the last years, increasing the number of objects in space, mainly in the Low Earth Orbits (LEO). Due to the short operational time, CubeSats boost the debris population. One of the requirements for space debris mitigation in LEO is the limitation of the orbital lifetime of the satellites, which needs to be lower than 25 years. However, there are space debris with longer estimated decay time. In LEÓs, the influence of the atmospheric drag is the main orbital perturbation, and is used in maneuvers to increment the losses in the satellite orbital energy, to locate satellites in constellations and to accelerate the decay.The goal of the present research is to study the influence of aerodynamic rotational maneuver in the CubeSat?s orbital lifetime. The rotational axis is orthogonal to the orbital plane of the CubeSat, which generates variations in the ballistic coefficient along the trajectory. The maneuver is proposed to accelerate the decay and to mitigate orbital debris generated by non-operational CubeSats. The panel method is selected to determine the drag coefficient as a function of the flow incident angle and the spinning rate. The pressure distribution is integrated from the satellite faces at hypersonic rarefied flow to calculate the drag coefficient. The mathematical model considers the gravitational potential of the Earth and the deceleration due to drag. To analyze the effects of the rotation during the decay, multiple trajectories were propagated, comparing the results obtained assuming a constant drag coefficient with trajectories where the drag coefficient changes periodically. The initial perigees selected were lower than 400 km of altitude with eccentricities ranging from 0.00 to 0.02. Six values for the angular velocity were applied in the maneuver. The technique of rotating the spacecraft is an interesting solution to increase the orbit decay of a CubeSat without implementing additional de-orbit devices. Significant changes in the decay time are presented due to the increase of the mean drag coefficient calculated by the panel method, when the maneuver is applied, reducing the orbital lifetime, however the results are independent of the angular velocity of the satellite.     

基于高斯伪谱法的碰撞规避策略研究

为保证在轨卫星运行安全，对于碰撞概率较高的空间交会情况需要进行规避机动，防止在轨卫星与空间碎片碰撞.选取连续推力策略进行规避机动，将空间碰撞规避过程转化为满足复杂约束的最优控制问题，采用高斯伪谱法对最优控制律进行求解，求解结果满足相应约束.研究结果为航天器有效规避空间碰撞威胁提供了有力支持.      

非相干散射雷达的空间碎片参数统计分析

采用匹配滤波方法处理了非相干散射雷达的原始采样数据(时长约7h), 共检测到394个空间碎片, 估算了其轨道高度、径向速度、散射截面、等效直径及径向加速度等参数, 统计分析了这些参数的变化特征, 得到穿过雷达 波束的空间碎片流量约为60h-1, 信噪比为10～1000, 空间碎片主要分布在600～1100km和1400～1600km两个高度区间, 散射截面 10-5～10-2m2, 等效直径3～10cm, 径向速度-1.5～1.5km·s-1, 径向加速度20～90m·s-2, 这对于中国的空间碎片探测与研究具有重要参考意义.      

Tumbling object deorbiting using spaceborne laser engagement – A CubeSat case study

This paper demonstrates active space debris removal using spaceborne laser systems. The laser beam and the surface of the target are discretised into multiple rays and finite elements, respectively, for laser-target interaction modelling, in which the laser ablation process is investigated. A high-fidelity attitude/orbit propagator tool is developed to account for both the linear impulse and angular impulse induced by the laser engagement and other perturbations. The laser system is activated only when three switch criteria are satisfied. In numerical simulations, laser pulses from international space station are generated to deorbit a 3U CubeSat with initially tumbling modes. The results validate the effectiveness of deorbiting tumbling CubeSats using spaceborne laser engagement, with the perigee height lowered by approximately $2.4\mathrm{km}$ in around $30\min$ after $2\mathrm{h}$ propagation. It is also found that the laser engagement becomes more effective for an initially faster rotating object.     

柱状弹丸撞击防护屏形成碎片云材料状态特性研究

微流星体及空间碎片的高速撞击威胁着长寿命、大尺寸航天器的安全运行，导致其严重的损伤和灾难性的失效。为精确估计微流星体及空间碎片高速撞击防护屏所产生碎片云对舱壁的损伤，必须确定碎片云中三种状态材料的特性，建立了碎片云特性分析模型，分别计算了柱状弹丸撞击防护屏所产生碎片云以及碎片云中弹丸和防护屏材料三种状态物质的质量分布。通过计算分析可见，弹丸以不同速度撞击防护屏所产生碎片云三种状态物质的质量分布是不同的，速度增大，液化和气化增强，对靶件的损伤小。而在速度小于7km/s时，碎片云以固体碎片的形式存在，对靶件的损伤大。     

Analysis of laser ranges and angular measurements data fusion for space debris orbit determination

In the framework of space debris, the orbit determination process is a fundamental step, both, for researchers and for satellite operators. The accurate knowledge of the orbit of space debris objects is needed to allow space debris characterization studies and to avoid unnecessary collision avoidance maneuvers.The accuracy of the results of an orbit determination process depends on several factors as the number, the accuracy, the kind of processed measurements, their distribution along the orbit, and the object-observer relative geometry. When the observation coverage of the target orbit is not homogeneous, the accuracy of the orbit determination can be improved processing different kind of observables. Recent studies showed that the satellite laser ranging technique can be successfully applied to space debris.In this paper, we will investigate the benefits of using laser ranges and angular measurements for the orbit determination process. We will analyze the influence of the number of used observations, of the covered arc of orbit, of each observable, and of the observation geometry on the estimated parameters. Finally, using data acquired on short observation arcs, we analyze the achievable accuracies for the orbital regimes with the highest space debris density, and to the consequences of the data fusion on catalog maintenance operations. The results shown are obtained using only real data (both angular and laser measurements) provided by sensors of the Swiss Optical Ground Station and Geodynamics Observatory Zimmerwald owned by the Astronomical Institute of the University of Bern (AIUB) and for some studies also using ranges provided from other stations of the International Laser Ranging Service (ILRS).     

考虑摩擦的空间抓捕过程碰撞动力学分析与控制

目前针对空间抓捕中的碰撞进行建模的方法中很少考虑摩擦因素。然而,摩擦作为碰撞过程中不可避免的现象,对碰撞动力学响应及整个空间抓捕任务有着不容忽视的影响。文章结合库伦摩擦理论和拉格朗日乘子法,建立了同时兼顾滑动和粘滞状态的摩擦模型,然后将求解到的摩擦力与碰撞力进行矢量合成,作为对碰撞模型的修正。另外,针对碰撞过程对机器人姿态产生的干扰,利用反 馈线性化设计了解耦控制器对基座姿态漂移进行稳定控制。数值仿真采用一个平面2灢DOF空间机器人,利用动量和动量矩守恒定理验证了动力学模型的正确性,同时基座姿态控制结果收敛说明了控制器的有效性。     

航天器与空间碎片的混合编队重构控制与应用

针对空间碎片清理问题,提出了一种利用航天器与空间碎片混合编队队形重构控制技术捕获碎片的方法。首先,分析了地/月—日系L2拉格朗日平动点附近的限制性三体环境,并建立了编队卫星相对运动动力学模型;其次,提出了以太阳光压力作为航天器与空间碎片编队队形重构的控制力,实现各从星接近空间碎片的目的;最后,设计了基于线性二次型的最优控制器,并在Matlab/Simulink环境下进行仿真实验。仿真结果表明该方法可控制从星到达期望的位置(空间碎片的位置),且太阳帆板的姿态变化在可控范围内,进而证明了该方案可以应用于复杂空间环境下的碎片清理任务。     

基于解体事件的空间碎片轨道演化算法研究

针对航天器解体事件所生成的空间碎片的演化过程,进行了数学分析,确定了新生成的空间碎片的速度增量,在该增量作用下碎片轨道会发生变更,本文根据该增量得出了空间碎片在轨道变更后的轨道根数,分析了在大气阻力摄动作用下,空间碎片的数目和轨道分布的演化情况,给出了相关结果,结果表明此算法可行。